User's Manual

S610S Manual - Hardware Installer Manual - Version 1.8
5
S
S
6
6
1
1
0
0
S
S
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
e
e
r
r
M
M
a
a
n
n
u
u
a
a
l
l
1
1
I
I
n
n
t
t
r
r
o
o
d
d
u
u
c
c
t
t
i
i
o
o
n
n
The S610S reader from CEM Systems is an intelligent ID card reader, designed to integrate with
an AC2000 SE or webEntry Access Control system. The S610S is an S600S with re-designed
two part case design and integral 125kHz read head. The S610S serial master reader is connected
to a serial controller, an S9064 for example. Other serial controllers include S9020, S9040 and
the S9032. The S610S serial reader can support and exit reader and a CEM Door Interface Unit.
READER MEMORY
Memory capacity is dependent on the type of card record. An 8-byte database stores the Card ID
along with the associated PIN, card status and time zone, up to 225,000 card records and
transactions held.
OFFLINE CARD VAILDATION AND ALARM BUFFER
During normal operation, the card holder database is downloaded to the reader and held in RAM;
this data is used to verify cards only if communications to the controller is disrupted. Alarms and
transactions are also held in memory and forwarded when communications are restored. Up to
8000 offline transactions, 256 time zones, 80 holidays are supported.
During extended offline periods the reader memory may be filled to capacity, then the oldest
alarms and transactions will be overwritten and the most resent will continue to be stored.
CARD TECHNOLOGY TYPES
The S610S family of readers can support the following access control card technologies.
CEM READER - PART NUMBERS
Description
125khz HID
Prox
13.56MHz
MiFare
HID Prox &
MiFare
13.56MHz
HID iClass SE
Picopass
External Read
Head
S610S
Model S610S Prox S610S MiFare S610S Multitech
** S610S
multi smart
c
ard reader
S610S
Picopass
S610S
External
Grey Product Code RDR /611/101 RDR /611/105 RDR /611/104
RDR/611/608
RDR/611/
606 RDR /611/109
Black Product Code RDR /611/111 RDR /611/115 RDR /611/114
RDR/611/618
RDR/611/
616 RDR /611/119
S610s
Exit
Model
S610
Prox Exit
S610
Mifare Exit
S610
Multitech Exit
** S610
multi
smart card
reader
Exit
S610 Picopass
Exit
S610 Exit
External
Grey Product Code RDR /612/101 RDR /612/105 RDR /612/104
RDR/612/608
RDR/612/
606 RDR /612/109
Black Product Code RDR /612/111 RDR /612/115 RDR /612/114
RDR/612/618
RDR/612/
616 RDR /612/119
** Indicates that the product is FCC Compliant
DOOR MODES
The S610S reader is used to control access at a standard entry/exit point but it can also be used
for a number of special operational modes; Control Post mode, Door mode, Passenger mode,
Trolley mode and Turnstile mode.
SMARTCARD TECHNOLOGY
Also available is the S610SP which has been specifically modified to use the Inside Technologies
PicoPass™ card. A full manual is available for this model of reader. Please contact your
supplier if Pico technology is required to integrate with your access control system.
HIGH SECURITY ENVIRONMENTS
CEM readers must be used in conjunction with a tamper protected DIU (Door Interface Unit) and
alarm when tampered. Where a DIU is supplied without an enclosure, the installer must fit an
enclosure and connect a tamper sensor. DIUs must be fitted on the secure side of the door or
other secure location. A battery backup power supply must be provided to ensure no false release
on mains fail. Current examples include DIU200, DIU210 or DIU230 PoE. The DIU enclosure
can only be accessible with the use of tools, e.g. screwdrivers or lock and key; flip open covers
are not acceptable.