User's Manual
Table Of Contents
- 1 Introduction
- 2 Quick Guide to setting up S610S
- 3 Connecting an S610S Master Reader
- 3.1 Open the S610 reader case
- 3.2 S610S Master Reader 12V Power and Data connections
- 3.3 Extra settings required, made on the reader
- 3.4 Addressing an S610S master reader
- 3.5 S610S Connecting Master Reader Inputs
- 3.6 Monitoring Inputs for Cable Tampers
- 3.7 Using an external read head
- 3.8 S610S Lock and spare output relay connections
- 4 Connecting an S610S to an Exit Reader
- 5 Connecting an S610S to a DIU
- 6 AC2000 Devices Application tasks
- 7 Door Modes
- 8 Interlock
- 9 Other AC2000 software configurations
- 10 S610S onboard diagnostic mode
- 11 Appendix
S610S Manual - Hardware Installer Manual - Version 1.8
31
7.1 Door mode
The most common mode for access control readers; on presentation of a valid card, access is
granted.
Open AC2000 Devices application; select the reader from the
Overview table.
From the
Current configuration table select Door Mode and click Edit, select Door and Save.
See also Interlock in Door mode, Interlock chapter in this manual.
7.2 Verification 24, Verification 32
Verification mode can be used to display cards embedded numbers on the reader’s LCD. Reader
address must be15, otherwise only a Card Read message is displayed.
Swiped card transactions are not stored on the AC2000 system. All compatible cards will be read
and the card number and site code displayed.
Verification mode is used on Validation readers. For more information on card validation, consult
the CEM AC2000 System Guide, or the S610S validation reader Quick Guide available from the
CEM website.
Desfire Verification
As above, but only applies to Desfire technology. The Mifare Desfire contactless smart cards
operate in the 13.56 MHz frequency range with read/write capability. The Desfire card type uses
encryption. Currently only supported by the S610S reader model. Verification mode is used on
Validation readers. Contact CEM for more information. Desfire verification is not supported in the
current firmware version B1.00.049.
Encrypted verification – Mifare Finch
Custom mode: Please contact CEM for more details. Card Number is transmitted from the S600s
Reader to the Workstation as an encrypted 6 characters (24 bit) or 8 characters.
32 bit Encrypted Verification mode is activated by choosing [ENCRYPTED VER 32] door mode.
When the Reader address is set to 8 to15, Encoded 8 Characters will be displayed on S600s LCD.
When reader address is set to 1, information will be transmitted through only COM0
24 bit Encrypted Verification mode is activated by choosing [ENCRYPTED VER 24] door mode.
As soon as card is swiped, Card Number is encoded and S600s Reader transmits Encoded 6
characters through selected output ports.
When the Reader address is set to between 8 and 15, Encoded 6 characters will be displayed on
S600s LCD. Note, In this mode, first two numbers are encoded and displayed only on LCD for
SITE.
7.3 Passenger mode
Passenger mode extends the normal door open time to Passenger time, set in Minutes. Passenger
mode can only be activated by a card holder with
Special Usage card status (set in the Personnel
application). The Special Usage card holder must press the reader keypad for normal door
open time or for
Passenger Time door open time. Ordinary card holders remain unaffected by
this mode, and will get ordinary access if their access level allows.
CONFIGURE PASSENGER MODE
Open AC2000 Devices application; select the reader from the Overview table.
From the
Current configuration table select Door Mode and click Edit, select Passenger and Save. The
Passenger Mode configuration will be down loaded to the reader by the system. A Special or Staff
Card will be required at the reader to activate Passenger door opening time.