Setup guide

ManualsBrandsControl 4 ManualsHome building and DecorDoor Station - Interior

™

Speciﬁcations

Dimensions (H x

W x D)

7.25” (183 mm) x 5.25” (133 mm) x 2.5”

(63.5 mm)

Weight 1.1 lbs. (.49 kg)

Shipping Weight 1.6 lbs. (.725 kg)

Network 10/100 BaseT Ethernet RJ-45 (preferred)

or WiFi (802.11 b/g/n)

Voltages AC - 100V - 240V

DC - 12V - 24V, 15W

Contacts (2 sets) DC: 48V

maximum operation (low voltage)

Relays (1) AC: 36V, 2A

DC: 24V

maximum operation (low voltage)

Grounding Requirements

Unlike the Door Station - Exterior, the Door Station

- Interior is made of plastic and has no grounding

requirements or ground connector.

Front Panel Description

Figure 1. Front Faceplate

1 Camera. 640 x 480 wide angle. Used for Video

Intercom.

2 Call button. Used to call the person inside the

unit or in another room.

3 Speaker. Used for Audio and video intercom.

4 Microphones (2). Used for audio and video

intercom.

Supported Models

• C4-DSC-EN-INT Door Station - Interior

AC, DC, POE & WiFi - Satin Black

Box Contents

Carefully unpack the Control4® Door Station from the

box and ensure that the following items are included

in the box. Remove the plastic protector from the

faceplate.

Contact your Control4 Dealer immediately if any

parts are missing or if any components are damaged.

• Control4 Door Station - Interior faceplate (model

C4-DSC-EN-INT)

• Mounting screws, security head (5)

• Security screw tool

• Plate attachment screw (1)

• Plastic faceplate (1)

• Warranty Card

Accessories

• Door Station Metal Back Box (C4-DSBB-M, sold

separately)

• Antenna Kit—WiFi/ZigBee 2.4 GHz, 26cm

(C4-AK-26cm, sold separately)

• Antenna Kit—WiFi/ZigBee 2.4 GHz, 3m

(C4-AK-3M, sold separately)

Door Station - Interior

Setup Guide

Summary of content (11 pages)

PAGE 1
™ Specifications Door Station - Interior Setup Guide Dimensions (H x W x D) 7.25” (183 mm) x 5.25” (133 mm) x 2.5” (63.5 mm) Weight 1.1 lbs. (.49 kg) Shipping Weight 1.6 lbs. (.725 kg) Network 10/100 BaseT Ethernet RJ-45 (preferred) or WiFi (802.
PAGE 2
Pre-Installation ™ This device is to be used for building interior installations only. Door Station - Interior Setup Guide 1 Find the best location for the Door Station. See “Mounting Tips” below. 2 Install the Door Station Back Box. See the Door Station Back Box Installation Guide for details. 3 Determine which network and power options to use (see “Network Options” and “Power Options”). Inside Panel Description 4 (WiFi only).
PAGE 3
Mounting Tips Please read the next sections, “Power Options” and “Network and Power Installations” to choose an Follow these tips for the best results. installation option that works best with the system 1 before installing the Door Station. Install the Door Station in a place where it will be protected from water. For interior use only. 2 Do not expose the Door Station to direct Power Options sunlight. 3 Find the best location for the Door Station.
PAGE 4
Power and Network Installations Option 2: Ethernet Connection with AC Power Choose one of these six (6) options to connect the This option sets up Ethernet and AC power. Door Station’s wiring: • Ethernet with PoE (preferred) To install the Door Station with Ethernet and AC • Ethernet with AC power: • Ethernet with DC • WiFi with AC 1 • WiFi with DC Plug the Ethernet cable into the Door Station (see Figure 4).
PAGE 5
To install the Door Station with Ethernet and DC To install the Door Station with WiFi and AC power: power: 1 1 2 Connect the neutral (N) (-) and hot (L) (+) wires Plug the Ethernet cable into the Door Station to the AC power source for the Door Station (see Figure 5). according to the national and local electrical Connect the negative (-) and positive (+) wires codes.
PAGE 6
Option 5: WiFi Connection with DC Power Figure 7. WiFi with DC Power Antenna This option sets up WiFi and DC power. Ensure that you have WiFi in the home. NOTE: WiFi requires an antenna (sold separately). To install the Door Station with WiFi and DC power: 1 Connect the negative (-) and positive (+) wires to the DC power source for the Door Station according to the national and local electrical codes. NOTE: The positive (+) wire’s connector is located on the bottom left side of the Door Station’s plate.
PAGE 7
Figure 8. WiFi with PoE WiFi Antenna the WiFi parameters. See the Composer Pro User Guide for details. Reset/Factory Restore the Door Station To reset or factory restore the Door Station: 1 Remove the faceplate and pull the Door Station out from the back box just enough to expose the Reset button (see Figure 2). 2 While powered press the Reset button on the bottom of the Door Station to reset or restore the Door Station. • Quick press. Press to reset the Door Station. • Long press.
PAGE 8
Figure 9. 26cm Antenna Kit Figure 11. Antenna to RSMA Connector Antenna Figure 10. 3m Antenna Kit RSMA Connector 3 Thread the other end of the antenna through the back wall of the back box (see Figure 12). Figure 12. Thread Antenna Through Back Box Antenna WiFi Antenna Kit Installation (Optional) Before you install the antenna: 1 Make sure the Door Station is assembled. 2 Make sure the Door Station back box is installed in the wall. See the Door Station Back Box Installation Guide for details.
PAGE 9
2 Thread the other end of the antenna through the Figure 14. Contact/Relay Locations back wall of the back box and through the interior wall as needed (see Figure 12). 3 Carefully insert the Door Station into the back box (see “Attach the Door Station”). Contact and Relay Connections You can connect devices to the contact ports or the 1 relay ports (see Figure 13).
PAGE 10
Security Best Practices The Door Station has connections for relays (to open doors, gates, etc.) and contacts. If installed without • Running MAC address filtering on the router or switch to force a hacker to spoof the Door Station’s MAC address to gain access to the LAN.
PAGE 11
- Utilisant usé ou endommagé les cordons de secteur peuvent avoir comme conséquence Regulatory/Safety Information la décharge électrique ou le feu. To review regulatory information for your particular - Entrez en contact avec toujours un Control4 products, see the information located on fournisseur des services Control4® autorisé the Control4 website at: http://www.control4.com/ pour l’aide si n’importe quelle réparation ou regulatory/. ajustement est exigée.