Instructions / Assembly

framed Panels facing out, or to the front. The smooth sur-
face of the glass will face into the shower. This orientation
gives you the front and back of each panel. Now, select
one of these panels to be the Outside Door Panel (#5) and
one to be the Inside Door Panel (#6).
A. Use two #8-32 x 3/8″ HWH Screws (#11) and
attach two Rollers (#10) to the top of the Outside
Door Panel (#5) on the front surface of the “fin”,
with the metal parts (the Nut side) against the
frame and the plastic Roller (#10) facing out of
the shower/shower (the same side as the tex-
tured side of the glass).
B. Use two more #8-32 x 3/8″
HWH Screws (#11) to attach
two Rollers (#10) to the top of
the Inside Door Panel (#6) of
the frame on the back surface
of the “fin”, with the metal
parts (the Nut side) against
the frame and the plastic
Roller (#10) facing into the
shower/shower (the same
side as the smooth side of
the glass).
STEP 9 Installing the Door Panels
Installing the Door Panels may be easier if you have
someone to assist you. Always wear gloves and safety gog-
gles whenever handling glass. NOTE: DO NOT allow the
panels to strike the shower/tile or each other.
A. Hold the Inside Door Panel (#6) so that the Rollers
(#10) are facing away from you. Standing outside
of and facing the shower enclosure, lift the Inside
Door Panel (#6) up and over the Bottom
Track/Curb (#2) and then lift the top rail up into the
Header (#1) and set the Rollers (#10) into the rear
track of the Header (#1).
STEP 6 Installing Wall Jambs
and Bumpers
A . With the narrow leg of each Wall Jamb (#3) toward
the inside of the shower enclosure, install the Wall
Jambs (#3) by setting each one down over the
Bottom Track/Curb (#2) and re-aligning the holes
of each Wall Jamb (#3) with the holes you drilled
in each wall.
B. Use two #8 x 1
1
/2″ FH
SMS Screws (#4), top
and bottom, to secure
each Wall Jamb (#3) to
the wall.
C. Use two more #8 x 1
1
/2″
FH SMS Screws (#4) to
secure Wall Jamb
Bumpers (#9) in the
center hole of each Wall Jamb (#3).
D. Tighten all #8 x 1
1
/2″ FH SMS Screws (#4).
STEP 7 Measuring and Installing
the Header
A. Locate the Header (#1) and two #6 x 3/8″ PH
SMS Screws (#14).
B. Measure the distance, wall to wall, at the top of
the Wall Jambs (#3). Cut the Header (#1) 1/16″
shorter than this measurement to allow for
clearance.
C. Install the Header (#1) over the ends of the Wall
Jambs (#3). Stand in the shower for the next
steps.
D. On both ends of the Header (#1), measure 5/16″
in from the end and 5/16″ up from the bottom
edge and mark these two points with a Pencil.
Using a 7/64″ Drill Bit, at each pencil mark,
c a r efully drill all the way through the Header (#1)
and into the Wall Jamb (#3).
F. Finish installation of the Header (#1) by securing
it to the Wall Jambs (#3) with the two #6 x 3/8″
PH SMS Screws (#14).
STEP 8 Installing the Rollers
on the Panels
Please note: Enclosures with Obscure or Smooth Rough
glass are installed with the textured s u r f a c e of the
Frame
Top
Outside
Panel
(Textured
side)
Outside Panel
(Textured side)
Inside Panel (Smooth side)
Nut
5
#500 - I0500 - 0703
Shorter
leg of Wall
Jamb
faces into
inside of
shower
Bottom
Track/
Curb
500 Install. Instruc. 7/1/03 8:24 PM Page 5