The Contour Perfit Mouse Control Panel User’s Guide For Windows Operating Systems
TABLE OF CONTENTS Part 1: Introduction.......................................................................................................... 1 Overview .......................................................................................................................... 1 Installing the Perfit Optical Mouse Driver ............................................................................ 2 Plugging the Perfit Optical Mouse into a USB port (recommended when available) .............
Part 1: Introduction Overview The Perfit Optical Mouse is the latest generation of the original “Contour Mouse”. This new design incorporates all the Ergonomic Award Winning features of the original and adds the latest in 800dpi optical technology, a scroll wheel and a light-touch 2-position rocker switch. After careful consideration of our customers and ergonomics professional’s feedback, the decision was made to not change the overall form factor of the device.
Installing the Perfit Optical Mouse Driver Warning: Other mouse software can interfere with installation or use of the Contour Mouse driver; please remove them before installing the Contour Mouse driver: 1. From the Start menu, select Settings, Control Panel, then Add/Remove Programs. 2. Select any mouse software that appears on the list. 3. Click Change/Remove to remove the mouse software. 4.
You are now ready to install the Contour Driver software: 1. Put the CD in the computer CD-ROM. 2. The computer should launch the CD and bring up the initial menu. (If the CD menu doesn’t appear, click on the Start menu, then Run. Click on Browse, select the CD and locate the correct setup file (.exe file). Once located, select Open then click OK.) 3. Follow the prompts to install the driver. Rebooting your computer will be necessary at the end of installation.
Part 2: Mouse Properties Panel Components Buttons Tab The Buttons Tab displays when the Mouse Properties panel is loaded. This Tab allows you to check that the driver properly recognizes your Perfit Mouse. By pressing your mouse buttons the corresponding button on the Mouse Properties panel will be highlighted (refer to figure below). This tab also allows you to program your mouse buttons.
Mouse actions − − − − System functions − − − − View functions − − Edit functions − − − − Keyboard keys functions − − − − − Click Right-click Double-click Autoscroll Close Maximize Minimize Start Menu Back Forward Copy Cut Paste Undo Backspace Enter Escape Page Down Page Up Any assignment made on a button will overwrite the existing assignment as soon as you confirm your changes by clicking the Apply button.
− Unaccelerated: the cursor moves according to the sensitivity you set. − Accelerated: for slow mouse movements the acceleration more or less corresponds to the sensitivity; the more you increase your mouse movement, the more the acceleration increases with respect to the sensitivity, according to the chosen acceleration profile (Slow, Medium, Fast). Scrolling Tab The Scrolling Tab allows you to set the properties of the scroll wheel and to adjust the panning speed.
Clicks Tab The Clicks Tab allows you to set and test the doubleclick properties. Two parameters can be set to adjust the double-click functionality: 1. the time that occurs between the first and the second click (speed), 2. the distance between the first and the second mouse position (area). The computer can decide to ignore a double-click if: - too much time has occurred between the first and the second click and/or - you have moved the mouse too much between the first and the second click.
Odometer Tab The Odometer Tab allows you to monitor how much you are using your mouse. You can do this by enabling the odometer option. The odometer has two meters: 1. a total meter, which monitors the total, 2. a trip meter, which monitors your mouse use starting from a particular date and time. These meters measure the distance you cover with the mouse. You can set the measurement either in inches, feet, miles, millimeters, meters or kilometers.
Part 3: Removing the Perfit Optical Mouse Driver Note: This process cannot be undone. All settings within the Mouse Properties Panel will be lost. You will have to reprogram all existing commands into the newly installed version. 1. From the Start menu, select Settings, Control Panel, then Add/Remove Programs. 2. Select Perfit Optical Mouse Driver. 3. Click Change/Remove to remove the mouse software. 4.
Part 4: Software License Agreement This is a legal agreement between you and Contour Design, Inc. (“Contour”). Before opening the sealed package and using the enclosed Contour Perfit Mouse Driver Software, Contour Perfit Mouse and accompanying documentation (the “Product”) read this agreement. By installing or using the Perfit Mouse Driver Software you agree to be bound by the terms of this Agreement. License Grant.
current price list. The foregoing warranties and remedies are void if there is a failure of the product because of accident, abuse, or misapplication. Any replacement software or hardware will be warranted for the balance of the remainder of the original warranty period or ninety (90) days, whichever is longer. DISCLAIMER AND LIMITATION OF LIABILITY.
restrictions set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at DFAR S 252.227-7013 or subparagraphs (c)(1) and (2) of the Commercial Computer Software Restricted Rights at 48 C FR 52.227-19, as applicable. Manufacturer is Contour Design, Inc., 10 Industrial Dr. Windham, NH 03087 USA.
Part 5: Contour Customer Care Registering your mouse 1. Log on to http://www.contourdesign.com and click the Registration link. 2. Please enter the requested information in the fields provided. Privacy Statement: Contour Design, Inc. strict policy is NOT to sell, rent, or otherwise make available to anyone outside of Contour Design, any information regarding our Customers.
