Synergy.doc Synergy® V Universal / DVR Remote Control Model RT-U62CD Programming And Operating Instructions Rev.
Synergy.doc 1. Introduction Your Synergy® V Universal / DVR remote control is simple to program, easy to use, and can operate up to five (5) electronic devices, which include: CABLE TV VCR DVD AUDIO Cable set-top terminals Televisions VCR DVD Audio receivers, amplifiers, CD players Before you can use your remote control, it must be programmed (set-up) to operate the above devices. 2.
Synergy.doc 2. From the Cable Setup Code list, locate the 3-digit code for your brand / model and enter it on the keypad of the remote control. The set-top terminal will turn off. 3. Then, press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.
Synergy.doc Point and Press® Programming This method allows you to program the remote control without using codes. Instead, the remote control automatically finds the correct command that you select in a variety of codes until you find the code that operates your device. You then lock in the correct code as described below. The following instructions describe how to program your remote control using the [CH +] or [CH -] buttons ("Power" function during programming).
Synergy.doc 2. Next, program your remote to operate the TV functions. Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates the TV functions (Power, Vol +/-, Mute) of your TV / VCR combination. 3. Last, program your remote to operate the VCR functions.
Synergy.
Synergy.
Synergy.
Synergy.
Synergy.
Synergy.doc Example: For code “035”, the remote will blink 10 times, then 3 times, then 5 times. To identify the 3-digit VCR code, press [VCR], then [OK] in step 1, then press [INFO]. To identify the 3-digit DVD code, press [DVD], then [OK] in step 1, then press [INFO]. To identify the 3-digit AUDIO code, press [AUDIO], then [OK] in step 1, then press [INFO]. 9.
Synergy.doc AUDIO AUDIO device (default), Cable or TV. To control volume / mute through your Cable set-top terminal in the remote’s Cable mode… 1. Press [CBL], then [OK] together until the [CBL] button illuminates. 2. Press [VOL +], then [CBL] for Cable volume. The [CBL] button will blink 3-times and go out. To return volume control to your TV, repeat step 1, then press [VOL +], then [TV] in step 2. 11.
Synergy.doc function. In the remote's TV mode, this button changes the Input Source (Input 1, Input 2...) on your TV. In the remote's VCR mode, this button changes the TV / VCR Input on your VCR. You can program this button so that in the remote's Cable mode, [INPUT] will operate the Input function on your TV or VCR, eliminating the need to change modes on the remote. To program [INPUT] to operate your TV Input function in the remotes cable mode... 1.
Synergy.doc Note: When you find the correct code, the fast-forward or rewind function of the device being programmed will be performed. To simplify programming using these buttons, insert a VHS tape or DVD in the device being programmed. You can also program your remote using the other available functions as follows: a. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL Æ TV Æ VCR Æ DVD Æ AUDIO Æ CBL…). b.
Synergy.doc Transport Functions - These are the [STOP], [PLAY], [FWD], [REW], [PAUSE] and [REC] buttons. In the remote control's Cable mode, these buttons operate your Cable set-top features. In the remote control's VIDEO mode, these operate your VCR or DVD functions. VIDEO Devices - VCR or DVD players. Device Setup Codes If you find that the setup codes listed above do not operate your devices, it is possible your remote was manufactured before the revision date printed on this Instruction Manual.
Synergy.doc 15. Using Your Synergy® V - Universal / DVR Remote Control Important: The following diagram shows how to use the buttons on your remote control to operate the DVR and PIP functions of the Motorola DCT 62xx series DVR set-top terminal. To access these functions, set the remote control to its Cable mode by pressing the [MODE] button, followed by the [CBL] button. CBL & TV on / off (programmable) Illuminate / select electronic device being operated.
