CONTEC PM-60 A Pulse Oximeter PM-60A Users Users’’ Manual CONTEC The document including some secret information, belongs to Contec medical systems co. LTD., in which any information is not allowed to be transmitted, copied ,or disclosed to any other companies except the recipient ones, even not for other commercial purposes. Catalogue Catalogue…………………………………………………………………………………………...2 ………………………………………………………………………………………… .
3 4 5 6 1 .1 Caution Proceeding……………………………………………………………………….3 1 .2 Manipulator Obligation …………………..........................................................................3 The Basics...................................................................................................................................3 .................3 2.1 Introduction.........................................................................................................................3 2.1.1 Intended Use .............
in accordance with its function and intended use. Observance of this manual is a prerequisite for proper product performance and correct operation and ensures patient and operator safety. This manual is based on the maximum configuration and therefore some contents may not apply to your product. If you have any question, please contact us. This manual is an integral part of the product. It should always be kept close to the equipment so that it can be obtained conveniently when needed.
as well as in home care environment. WARNING This pulse oximeter is intended for use only by clinical professionals or under their guidance. It must only be used by persons who have received adequate training in its use. Anyone unauthorized or untrained must not perform any operation on it. 2.1.2 Contraindications None. 2.1.3 Components This pulse oximeter consists of a main unit and a SpO2 sensor. 2.
History: Storage of latest 10000 case history by SD card. Permit to review momentarily. Alarm: Ajustable High and Low limits. Three level audible and visual alarm , latest 50 alarm information and waveform displays 8 seconds which 4 seconds are before a certain time when the alarm is turned on and 4 seconds are after appointed time when the alarm is turned on. Wave: Storage of 24 hours waveform, and only the realtime stored patients have waveform. 3.
Accuracy: ± 2%(70%~100%, Adult/Pediatric, non-motion) ± 3%(70%~100%, Neonate, non-motion) 0% ~ 69% unspecified Alarm Range: 0% ~ 100% Refreshing Rate: 1s Pulse Rate: Measurement Range: 25 ~ 250 bpm Resolution: 1bpm Accuracy: ± 3 bpm (non-motion) Alarm Range: 25 ~ 250 bmp Refreshing Rate: 1s 4 Function Instructions 4.1 Main Interface The system will enter automatically the main interface after first startup.
Model 4-1-3 Main 1. Patient ID Area: This area shows the ID number of the patients monitoring currently. 2. Patient category Area: This area shows the patient range. Patients are classified as adult, pediatric and neonate. 3. System Time Area 4. Heart Rate Area: Click the button can shield the sound of the heart murmur. The the button flicker alternately after the sounds are turned off . 5. Battery symbol Area: This area shows the electrical voltage of the battery. 6.
indicates that alarm sounds are paused. 11. Waveform Area: This area displays SPO2 real time waveform. 12. Function button Area 4.1.2 Function button: Functions as follows: Enter the new patient case history menu. Patient’s case history should be set up and stored 10,000 at best . Enter the data review menu. Review the monitoring data of the current patient or the patients who had been stored previously. Enter the system setup menu. Amend the system setup.
personal information of the patient monitoring currently into the SD card. 4.3 Data Review Interface 4.3.1 Data Review Interface Click the “ ” button of the main interface to enter the patient data review interface. Data review interface showed as followed: Model 4-3-1 Data Review Users can review the monitoring data of the current patient or the patients who had been stored previously by selecting "Patient ID".
TrendTable Interface showed as followed: Model 4-3-2 TrendTable The detailed information of the key as following: Max : Min: Ave: The maximum of the Parameter data in the logical range The minimum of the Parameter data in the logical range The average of the Parameter data in the logical range 4.3.3 TrendGraph Interface TrendGraph Interface showed as followed: Model 4-3-3 TrendGraph 4.3.3.１. Click one point on the screen to descry the parameter value of Spo2 and PR at a certain time. 4.3.3.２.
SpO2 desaturation event is defined as drop in SpO2 by at least N% for a minimum duration of L seconds. N and L are configurable, and is defaulted to 4 and 10. Pulse event is defined as change in pulse rate by at least N bpm( beats per minute) for a minimum duration of L seconds. N and L are configurable, and defaulted to 6 and 8. You can set the analysis parameters in the "System Setup" Menu. 4.3.
Setup interface showed as followed: Model 4-4-1 Setup Instruction: Monitoring setting and producer setting Options as follows follows:: Item Purpose Producer setting Choosing scope Spo2 ALM Turn on/off Spo2 alarm OFF OFF Spo2 ALM LVL Spo2 alarm level MID LOW, MID, HIGH Spo2 ALM HI Spo2 alarm high-level 99 0----100 Spo2 ALM LO Spo2 alarm low-level 80 PR ALM Turn on/off PR alarm OFF OFF PR ALM LVL PR alarm level MID LOW, MID, HIGH PR ALM HI PR alarm high-level 110 0-----300 P
4.4.2 System Setup Click the “ ” button of the Setup menu to enter the System Setup menu interface. System Setup menu interface showed as followed: Model 4-4-2 System Setup １. 4.4.2. 4.4.2.１ Users can set system sounds and overtime of the backdrop lighting . 2. SpO2 Parameters 4.4.2. 4.4.2.2. Drop for Event (%): value, in %, to qualify as an SpO2 (Desaturation) Event. Minimum Event Duration (sec): value, in seconds, of SpO2 decrease that qualifies as an SpO2 (desaturation) event.
4.2. 3. 4. 4.4.2. 4.2.3. Click “OK” to set new analysis parameters or click “Cancel” to leave them unchanged. All setting will turn back to manufacture's setting when Click “ 5 ”button. Maintenance and Cleaning Use only the substances approved by us and methods listed in this chapter to clean or disinfect your equipment. Warranty does not cover damage caused by unapproved substances or methods.
delivered with the accessories. 5.1 Safety Checks Before every use, or after your pulse oximeter has been used for 6 to 12 months, or whenever your pulse oximeter is repaired or upgraded, a thorough inspection should be performed by qualified service personnel to ensure the reliability. Follow these guidelines when inspecting the equipment: � Make sure that the environment and power supply meet the requirements. � Inspect the equipment and its accessories for mechanical damage.
� Isopropanol (70%) To clean your equipment, follow these rules: 1. Shut down the pulse oximeter and disconnect it from the power line. 2. Clean the display screen using a soft, clean cloth dampened with a glass cleaner. 3. Clean the exterior surface of the equipment using a soft cloth dampened with the cleaner. 4. Wipe off all the cleaning solution with a dry cloth after cleaning if necessary. 5. Dry your equipment in a ventilated, cool place. 5.
Battery Too Low SPO2 Too High SPO2 Too Low PR Too High PR Too Low 6.2.
