Precautions regarding Warranty and Specifications This product was jointly developed and manufactured by Mitsubishi and CONTEC. Note that there are some precautions regarding warranty and specifications of the product. < Warranty > The gratis warranty term of the product shall be for one (1) year after the date of delivery or for eighteen (18) months after manufacturing, whichever is less. - The onerous repair term after discontinuation of production shall be for six (6) years.
Safety Precautions Review the following definitions and precautions to use the product safely. Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Review the meanings of these labels to operate the equipment safely. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Supported Wireless Networking Standards This product conforms with IEEE 802.11a and IEEE 802.11b/g. It can be set to the channels corresponding to the countries listed below. Channel*1 Standard U.S.A. Europe China (NZ2WL- Korea Taiwan (NZ2WL- (NZ2WL-US) (NZ2WL-EU) CN) (NZ2WL-KR) TW) 36, 40, 44, 48, IEEE802.11a 149, 153, 157, 161, 36, 40, 44, 48ch 165ch IEEE802.
Handling Precautions WARNING - Do not use the product where it is exposed to flammable or corrosive gas. Failure to do so may result in an explosion, fire, electric shock, or failure. - The product could be very hot in the operation. Please do not touch with hands or body. It may cause burns. - To avoid electric shock, please do not touch the system with a wet hand. - As this product contains precision electronic components, do not use or store it in a place subject to shock or vibration.
- By grounding the FG terminal, this product is negatively grounded, so note that connecting a positively grounded device to this product may cause malfunction, heat generation, faults, or damage. - Note that an electrical potential difference existing between the ground of this product and the negative ground of its power supply may cause malfunction, heat generation, faults, or damage.
Connection to MELSEC Series Equipment The NZ2WL Series can be connected to various programmable controllers and display units. Connectable Equipment The following MELSEC Series equipment can be connected.
Note on Connections CAUTION - - - - - - Do not use this product for applications that must transmit or update data regularly or within a given time period, such as the cyclic transmission of a programmable controller. Transmission delays cannot be obtained through calculations for Ethernet communications using this product. Use this product with the access point and station in visual range of each other (so that the antenna on one device is visible from the antenna on the other device).
CONDITIONS OF USE FOR THE PRODUCT (1) (2) viii Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions; i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident; and ii) where the backup and fail-safe function are systematically or automatically provided outside of the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
Terminology/Abbreviations The following terms and abbreviations are used in this manual for convenience. Full term All five NZ2WL models (NZ2WL-US, NZ2WL-EU, NZ2WL-CN, NZ2WL- Term used in this manual NZ2WL-xxx KR, NZ2WL-TW) NZ2WL-US (for U.S.A.
Packing List Thank you for purchasing this Mitsubishi product. The product package should contain the items listed below. Use the following list to confirm the contents of the product package. If you discover any damaged or missing item, contact your local authorized dealer. Contents Name Pcs.
Table of Contents Packing List ......................................................................................................................................... x 1. BEFORE USING THE PRODUCT 1 Overview ............................................................................................................................................. 1 Features ........................................................................................................................................
4. WIRELESS LINK MODE AND WIRELESS LAN FUNCTION 20 Wireless Link Mode .......................................................................................................................... 20 Standard Infrastructure Mode ..................................................................................................... 20 Compatible Infrastructure Mode ................................................................................................ 21 Advanced Infrastructure Mode ...................
7. TROUBLESHOOTING 62 When Communication Fails .............................................................................................................. 62 Setup Screen Unavailable on Web Browser...................................................................................... 63 When the Product Does Not Start ..................................................................................................... 63 8. APPENDIX 64 BSHardware Setup ..............................................
MEMO xiv NZ2WL - xxx
1. Before Using the Product 1. Before Using the Product This chapter provides information you should know before using the product. Overview The NZ2WL-xxx is a wireless LAN adapter that conforms to IEEE 802.11a/b/g standards of various countries and features a wide input power supply (12 to 24 VDC) and can be configured either as an access point or station.
1. Before Using the Product ■WDS feature equipped *6 Up to six units can be connected wirelessly between access points. ■QoS support Bands are secured for specific communication, such as VoIP, and communication quality is guaranteed. ■SNMP agent feature equipped The feature enables network management using SNMP supported network management software. ■Protect Mode available when using IEEE802.11g Stable communications are enabled even when IEEE802.11b-compliant products are also used.
1. Before Using the Product Environment Use this product in the following environment. If used under environmental conditions exceeding these ranges, the board may overheat, malfunction, or cause a failure. Operating ambient temperature 0 - 50ºC Operating ambient humidity 10 - 90%RH (No condensation) Corrosive gases None Floating dust particles Small amounts (non excessive) Inspection Inspect the product periodically as follows to use it safely.
2. Setup 2. Setup The antenna must be mounted and installed properly before configuring this product. Follow the setup procedure for the product shown below. Part Names and Functions LED: Indicates the status of the power supply, wired LAN and wireless LAN. Refer to Tables 2.1 - 2.3 for details. DIP switch: Used for initialization and for operation in IP-less mode. See Table 2.4 for the setting method. Antenna connectors: Connect to the antennas. Connect supplied dipole antennas to these connectors.
2. Setup Table 2.2. During File Write LED name Status POWER Flashing WLAN simultaneously *1 LED display File write in progress *1 Except writing of log files (no flashing) Do not restart or turn off the module during the File writing. Table 2.3. Error Display LED name Status POWER Flashing twice WLAN ON LED display Wireless LAN error DIP switches Table 2.4. DIP Switches ON OFF Operation / function Turning on this switch flashes the POWER and WLAN LEDs.
2. Setup Connectors Table 2.5. Power Connectors Name Power connector Function Power terminal connector (included in the package): MC1,5/3-ST-3,5 (made by Phoenix Contact Inc.) The applicable cable is AWG28-16. (The cable length must meet the power supply specifications.) The applicable bar solderless terminals are AI0,25-6BU, AI0,34-6TQ and AI0,5-6WH (made by Phoenix Contact Inc.) Secure the connector with a retention bracket. Connect the power cable to the power terminal connector by screw connection.
2. Setup Attaching the Antennas Use this product with the antennas included. The following describes how to attach the supplied dipole antennas. (1) Straighten both the antennas, as shown below, and attach them to the antenna connectors on the main unit. The antennas screw onto the antenna connector. Adjust the position of the bending part of the antennas taking into consideration how the antennas will be oriented. Next, place the supplied rubber caps over the antennas and cover the antenna connectors.
2. Setup Power Supply - The input voltage range of this product is 12 to 24 VDC ±5%. Using a power supply outside of that range may cause a malfunction or accident. - Connect the cables correctly to the Vi+ (12 to 24 VDC ±5%), Vi- (GND), and FG connectors. - Use a power source that starts up within the input voltage range of 11.4 VDC or higher within 24 ms. Using a power supply that does not satisfy these conditions may cause a malfunction or accident. Input Voltage (V) 25.2 24 12 11.
2. Setup Grounding the NZ2WL Connect the cables to the applicable connectors. Process the cables as needed and ground the product. Figure 2.5. Grounding the NZ2WL CAUTION - The negative electrode (Vi-) terminal and the FG terminal of this product's power supply terminal are connected to the metal casing.
2. Setup Installation Using Mounting Brackets Mounting on a Desktop (Horizontally) When the product is used horizontally, it can be mounted on a desk or other surfaces using brackets. Attach the product and brackets using the supplied bracket screws (tightening torque: 0.588 Nm), as shown below, and place the side with the brackets down. Then secure the brackets on the desk using tapping screws. Figure 2.8.
2. Setup CAUTION When mounting the product on a desk or wall, place the product down with one of the orientations shown to the right. When mounting the product vertically, orient the product with the LAN port on the bottom. When mounting the product horizontally, orient the product with the WLAN LED on the bottom. When mounting the product to a wall, secure the rear of the product or the side of the product closest to the WLAN LED to the wall.
3. Connecting to Devices and Setup Methods 3. Connecting to Devices and Setup Methods This product is set up via a network using a Web browser or TELNET. Follow the setup procedure below once the product is set up. Setup Methods Although the NZ2WL-xxx can be set up precisely to construct an advanced wireless LAN environment, there are two different setup methods available: web browser and TELNET. Web browser - Settings are easy with a graphical display and a help function.
3. Connecting to Devices and Setup Methods Setup Using Web Browser This section describes the setup method using a Web browser. The following Web browsers can be used (recommended Web browsers). Note that a proper display may not be shown on any browser other than the following ones. Enable the JavaScript function in the browser setting as it is used. Supported web browsers (recommended) - Microsoft Internet Explorer 6 or later (7 or later recommended) - Mozilla Firefox 1.0 or later (3.
3. Connecting to Devices and Setup Methods Connecting to This Product Using Web Browser Start up a Web browser and enter the IP address of this product after “http : //” in the address bar. If connecting to this product for the first time, enter the default IP address. When the default setting IP address is 10.144.0.1, enter as follows. http://10.144.0.1/ Connecting to this product displays the “Access Point Manager” login window, shown below.
3. Connecting to Devices and Setup Methods Setup Using Web Browser Select “Setting” in the left-hand menu ((1) in Figure 3.3) and further select the desired setting items from the opened menu. Information such as setting items will be displayed in the right-hand frame. Figure 3.3. Setting by Access Point Manager (KR) Click “Submit” ((2) in Figure 3.3) after changing settings on each page to temporarily save the settings in this product.
3. Connecting to Devices and Setup Methods Setup Using TELNET This section describes how to perform setup using TELNET. This procedure requires an application in which TELNET can be used. In Windows, “Command Prompt” can be used. Connecting to the Product Using TELNET Start up an application in which TELNET can be used (e.g. Command Prompt) and enter the IP address of this product after the telnet command*1. When connecting to this product using TELNET for the first time, enter the default IP address.
3. Connecting to Devices and Setup Methods If the login is successful, the following window is displayed after a while. Figure 3.5. Window after TELNET Login CAUTION ”Shift JIS” is used as the character code displayed during TELNET connection. Check the character code of the TELNET application if the characters become garbled.
3. Connecting to Devices and Setup Methods Setup Using TELNET After login, enter the number of the item shown in the top menu depending on the desired execution, and then press “Enter”. To perform configuration, enter “2” for “Configure”. The items in the top menu are as follows. Table 3.1. TOP Menu Menu Description 1. Exit Exit terminal setup. 2. Configure Selected to configure settings. 3. Write Configuration 4. Reboot 5. Update System Parameters 6. Download 7. Upload Used to save the settings.
3. Connecting to Devices and Setup Methods TELNET Key Operation Select items from the TELNET menus by entering the corresponding number. In addition to numbers, the following commands can be also used. The keys can be used in all the menus. Capital and small letters are not differentiated.
4. Wireless Link Mode and Wireless LAN Function 4. Wireless Link Mode and Wireless LAN Function This chapter describes the major functions of the NZ2WL series as a wireless LAN system and the wireless link modes of the product along with configuration examples of networks available in the wireless link modes. Wireless Link Mode This product has three wireless link modes. The available functions and network configurations differ depending on the mode.
4. Wireless Link Mode and Wireless LAN Function - Advantages (1) If the IP tunneling function is used, communication can be performed over different routers without changing IP addresses. (2) Allows log-in restrictions (security function). (3) Improves security using the WSL (Wireless Security Link). Compatible Infrastructure Mode This mode allows the product to be networked with other manufacturers’ Wi-Fi certified wireless terminals other than the NZ2WL series.
4. Wireless Link Mode and Wireless LAN Function Advanced Infrastructure Mode The Advanced Infrastructure mode is a mixture of the Standard Infrastructure and Compatible Infrastructure modes. The Advanced Infrastructure mode can be used only when the product is configured as an access point. Figure 4.3. Advanced Infrastructure Mode On the terminal set to the Standard Infrastructure mode, the NZ2WL series' unique functions can be used.
4. Wireless Link Mode and Wireless LAN Function Comparison of Main Functions The three wireless connection modes mentioned earlier have different wireless LAN functions. The following table lists main functions of each mode and gives a brief explanation of each function. ○ ×" indicates that the function cannot be used. " " indicates that the function can be used and " Table 4.1.
4. Wireless Link Mode and Wireless LAN Function MAC address filtering This function can be used only when the product is configured as an access point. This function enables only the terminals whose MAC address has been registered to be connected. Bridge packet control This function can be used only when the product is configured as an access point. An AP can pass only data from network devices whose MAC address has been registered to the AP.
4. Wireless Link Mode and Wireless LAN Function Installation in a Network This section describes how to install the product to construct a network with improved performance and discusses the general features of the wireless network and characteristics of radio waves, as well as the guidelines for constructing the network. Features of the Wireless Network In general, the operation of a wireless network is the same as for other similar types of LAN.
4. Wireless Link Mode and Wireless LAN Function Operating Environment and Radio Waves When using this product to construct a network, install and operate it considering the radio environment to optimize the performance. Is it allowed to use wireless devices at the installation location? In some medical institutions and laboratories, radio-sensitive precision instruments are used and it may be prohibited to use wireless devices. Radio waves are attenuated.
4. Wireless Link Mode and Wireless LAN Function Constructing a Network This section gives some pointers and cautions relating to constructing a network using the AP and station and provides some practical examples. (1) This product conforms with the standard wireless LAN specifications such as IEEE802.11a, IEEE802.11g and IEEE802.11b. This enables setting to the same channel as that used in each country and wireless communication between access points and stations responding to each channel.
5. Setup and Status Display 5. Setup and Status Display This chapter explains about setting items and status displays of this product. Always read Chapter 2 “Setup” and Chapter 3 “Connection to Devices and Setup Methods” for preparation before performing setup or viewing the status. At the time of purchase, this product is configured as an access point. This section describes how to setup this product and status displays using a web browser.
5. Setup and Status Display ■Access Point Type The application type of the access point can be set by selecting “normal”, “master”, or “backup”. The “master” device integrates access points on the network and the “backup” device substitutes for the master AP if the master AP stops working for some reason. As a basic rule, select "master". You can also select "master" when the product is configured as a station. Normally, you do not have to change the default setting.
5. Setup and Status Display ◆Ethernet ■Port Speed Select the port speed setting. Select one of “Auto”, “100M Full Duplex”, “100M half Duplex”, “10M Full Duplex”, or “10M half Duplex”. Factory default setting: Auto CAUTION - If one side is set to "Auto" and the other side is set to "100M Full Duplex", the communication mode for the "Auto" side is recognized as "100M half Duplex". In this case, there may be a high error rate and normal communication may not be possible.
5. Setup and Status Display ◆Wireless LAN To change the wireless LAN standard, wireless connection mode, take three steps of “Basic” -> “Details” -> “Security” to make their respective settings. For any other item, you can change the setting on under “Details” or “Security”. ▼Basic ■Interface Disabling “Interface” disables the internal wireless LAN module.
5. Setup and Status Display ■Unit Type Select either “Access point” or “Station”. Factory default setting: Access point Table 5.2. Unit type Unit type Overview Access point Master access point controlling other stations or access points operating in station mode. Station Access points controlled by (logged into) another access point. For use when using as a bridge, for example. ■XR function To enable the XR (eXtended Range) function, set to “set to “Enable”.
5. Setup and Status Display ■Transmission Rate *1 Sets the wireless transmission rate. Select one from “Auto”, “54Mbps”, “48Mbps”, “36Mbps”, “24Mbps”, “18Mbps”, “12 Mbps”, “9 Mbps”, “6 Mbps” for IEEE802.11a. Select one from “Auto” , “11Mbps”, “5.5Mbps”, “2Mbps”, “1Mbps” when IEEE802.11b. Select one from “Auto”, “54Mbps”, “48Mbps”, “36Mbps”, “24Mbps”, “18Mbps”, “12 Mbps”, “9 Mbps”, “6 Mbps”, “11Mbps”, “5.5Mbps”, “2Mbps”, “1Mbps” for IEEE802.11g. You can use "Max." to set the maximum transmission rate.
5. Setup and Status Display ■Super A/G This item sets the Super A/G feature for increasing the communication speed of wireless LAN. To use Super A/G, enable the feature. Of the Super A/G feature, enable "Frame bursting" to use the frame bursting function and enable "Real-time compression" to use the compression function. To enable the Super A/G feature, usually, enable "Frame bursting".
5. Setup and Status Display ■Statistic Node Address This item is available when the wireless link mode is "Compatible Infrastructure", the unit type is "Station", and the multi-client function is "Disable". Enter the MAC addresses of the PCs connected to the product. Generally, set this item when connected to a receive-only device, such as a POS terminal. Enter the MAC address "00-00-00-00-00-00", which consists of nothing but 0, meaning the function is disabled, when not using the function.
5. Setup and Status Display ■Priority AP This item available when the unit type is “Station”. This item allows you to specify the access point to be connected preferentially. Enter the wireless MAC addresses of the access points in AP1 to AP5. Wireless MAC addresses of access points can be checked on “Status” for each access point and “Wireless MAC address” of the “Wireless LAN”. The access points to be connected are assigned priorities in ascending order beginning with AP1 (followed by AP2, …, AP5).
5. Setup and Status Display Factory default setting: 100 (ms) ■DTIM This item is available when the unit type is “Access point”. Set the interval at which to add a DTIM (Delivery Traffic Indication Message) to a beacon signal, which is information for recovering a station from power-save mode. Enter a value between 1 and 255. Setting this item to 1 adds a DTIM to each beacon signal and setting it to 2 adds one to every other beacon signal.
5. Setup and Status Display ■Scan Channels This item is available when you choose the channel to scan. Selecting the "Scan Channels" might shorten the scan time and make a roaming smoothly. Enter each channel with the ",". (Example: 36, 40, 48 to scan the channels of 36, 40, 48 only...) If you want to scan all of the channels that support, leave it blank. Normally, you do not have to change the default setting.
5. Setup and Status Display ▼Security ■Encryption This setting specifies whether to enable or disable encryption. You can select a type of encryption from among "WEP", "AES", "AES-OCB", and "TKIP". If you select "AES" or "TKIP", one of the WPA functions described later can be used. When "TKIP" is selected, use one of the WPA functions. If you disable encryption, neither key can be used as the default key. Factory default setting: Disable Table 5.5.
5. Setup and Status Display ■Size / Key #1 - #4 Set this item when encryption has been set to "WEP", "AES", or "AES-OCB" and the WPA function is disabled. Specify the size and value of the key to be used for encryption. The acceptable size and number of digits of the key depend on each type of encryption. Enter the key in hexadecimal (0 - 9, a - f, or A - F). Factory default setting: (No input) Table 5.6. Encryption Number of Key Input Digits Size and No.
5. Setup and Status Display ID terminals (those with no ESSID assigned) and hides the AP’s ESSID from external references to the access point. Using the function restricts illegal access using ANY ID and prevents the ESSID from being easily known to third parties. Factory default setting: Disable ■MAC address filtering This item is available when the unit type is “Access point”. Select whether to use the MAC address filtering function.
5. Setup and Status Display ◆IEEE802.1X ■IEEE802.1X Set this item to “Enable” to enable the function of IEEE802.1X. When the IEEE 802.1X function is "Enable" and WPA/WPA2/WPA-AUTO is not used, be sure to select "WEP" for the wireless LAN security setting to enable key exchange. This function is not available when the unit type is "Station", so select "Disable". Factory default setting: Disable ■MAC Address Authentication Function To enable the MAC address authentication function, set it to "Enable".
5. Setup and Status Display ■(RADIUS server) Pre-shared Key Enter the pre-shared key of the RADIUS server. Factory default setting: (No input) ◆Extension ■Bridge Packet Control This item is available when the unit type is “Access point”. Enabling bridge packet control prevents file sharing among clients under the same access point.
5. Setup and Status Display ■Network Time Enabling the network time function can synchronize the access point time with the network time. To enable this function, set the IP address and time zone of a network time server on the network. (Example: For use in Japan, enter “+09 : 00” (meaning UTC + 9 hours) as the Japan standard time is nine hours ahead of Universal Time Coordinated (UTC).) Factory default setting: Function …Disable IP Address … 0.0.0.
5. Setup and Status Display ■Protocol Filter When this is "Enable" and a filter is registered, specific protocol (such as TCP and UDP) packets can be blocked or allowed. To edit a filter, click the "Edit List" button to open the window for setting the protocol filter list, and then edit the filter. Set the following settings in the window for setting the protocol filter list, and then click the "Add" button to register the filter to the list. Table 5.7.
5. Setup and Status Display ■Roaming Notification Roaming notification packets are packets that notify other access points and switching hubs that a station has moved when station roaming has occurred. When the "Send notification packets" setting is "Enable", notification packets are sent when station roaming occurs. "First login notification" is a setting that is enabled for access points whose wireless link mode is "Standard Infrastructure".
5. Setup and Status Display ■Community Name Enter the SNMP authentication string. The SNMP authentication string serves as a password to access this product using SNMP. Programs use this community name to access MIB of this product. *1 Enter a string of up to 32 alphanumeric characters. The community name is case sensitive. Factory default setting: public *1 Management Information Base: complies with RFC1213 and RFC1493 ■Access Right Set the access right for the community.
5. Setup and Status Display ◆VLAN ■VLAN This item is available when the unit type is “Access point”. Set this item to "Enable" to enable the VLAN function. Factory default setting: Disable. ■VLAN ID This item is available when the unit type is “Access point”. Specify the VLAN ID of this product between 1 and 4094. Factory default setting: 1 ■Guest Access This item is available when the unit type is “Access point”.
5. Setup and Status Display If you want to guest connection, you can use the wireless LAN settings that you set in the "wireless LAN" above. Encryption of the wireless LAN setting, when you use the WPA or WPA-PSK, can not add a VLAN group to the VLAN table. ESSID and VLAN ID of the VLAN group to be added to the VLAN table do not overlap with other groups. If you enable the VLAN function, data to be handled in the wired LAN interface will be only the frame with a VLAN tag.
5. Setup and Status Display ■Detailed Setting You can select the types of events to be logged. Setting [Login], [Logout], [Login NG], [Roaming], [Tunnel Start], [Tunnel Stop], [Application Login], [Application Logout], [Auth Success / Error] and [Date / Time Set] to “ON” allows the selected events to be logged. Setting them to “OFF” prevents them from being logged. See Table 5.8 for a description of the types of events.
5. Setup and Status Display ■Interfaces - MTU The maximum transmission unit (MTU) is the maximum length of data that can be transmitted in one transmission. This displays the MTU for each interface. - Transfer Speed Displays the data transfer speed for each interface. - MAC Address Displays the MAC address for each interface. - Interface / Link Status Displays whether each interface is active and connected to the network. - RX Octets Displays the number of data bytes received by the access point.
5. Setup and Status Display ■Wireless - LAN information Wireless LAN Standard Displays the currently operating wireless LAN standard. - Wireless Link Mode Displays the currently operating wireless LAN mode: Standard Infrastructure, Compatible Infrastructure, or Advanced Infrastructure. - Unit Type Displays the current wireless LAN type: Access point or Station. - Module ID Displays the ID of the wireless device incorporated in this product.
5. Setup and Status Display ■Wireless - Statics Information Transmit Unicast Packets Displays the total number of unicast packets transmitted by the wireless interface of this product. - Transmit Multicast Packets Displays the total number of multicast packets transmitted by the wireless interface of this product. - Transmit Unicast Bytes Displays the total number of unicast bytes transmitted by the wireless interface of this product.
5. Setup and Status Display ■Wireless - node information Wireless MAC Address When the unit type is "Access point", this displays the MAC address of the wireless LAN card. When the unit type is "Station", this displays the MAC addresses of the access points located near this product. - Mode Displays the wireless LAN standard (802.11a/b/g) being used by the device(s) where the MAC address is displayed.
5. Setup and Status Display ■MAC Address Table - MAC Address Displays the MAC addresses of external devices obtained when this product connects to the devices. - Interfaces Displays the interfaces of the product that obtained the MAC addresses of external devices. - Aging Time Displays the aging time (time on the network) of external devices displayed by MAC address. As the duration that the external device is not connected continues, the aging time decreases proportionally.
5. Setup and Status Display ■Log Information Log information recorded in this product is displayed. To clear log information, click “Clear log information”. For main events displayed on the logs and their outlines, see the table below. Table 5.8. Events to Be Logged Event Description Start Indicates that the AP has been activated. Link Up Indicates that the wired link has been connected and the link speed. Link Down Indicates that the wired link has been disconnected.
6. Maintenance 6. Maintenance This chapter describes how to perform maintenance on this product and explains the tools to be used. Here, “maintenance” means the following: log file collection and saving and restoring the software settings. This product does not support firmware updates. Maintenance Tool The FTP can be used for maintenance of this product. This section explains about maintenance methods using the FTP. Log File Collection Log files can be collected by using the FTP via LAN.
6. Maintenance Saving a Setting File Saving a software setting file of this product has the following benefits: - If you have more than one product and all the products should have the same settings, setting is required only for one product. The setting file can be used for the remaining products. (As this sets the same IP address for all the products, change the IP address for each product in advance.) - The old settings can be restored easily if a fault causes the settings file to be erased.
6. Maintenance Restoring the Software Settings The software settings of this product can be recovered by using the saved setting file. The setting file is restored by storing the previously collected CONFIG file (MACFLIST file if needed) in the memory. Restore Settings Using FTP Follow the instructions below to restore software settings using the FTP. (1) Move to the folder where the file is stored. (2) Run the FTP to log in to this product. (3) Transfer the setting file (CONFIG).
6. Maintenance Time Setting Set the time on this product. Enter the year (4 digits), month, day, time (24-hour notation), minute, and second, and then click the [Update] button. If you enter one digit for the month or day, a zero will be added to display the month or day in two digits. You can enter either one digit or two digits with an added zero. (Example: 2010/8/12 13:06:01) Clicking the [Set PC Time] button copies the time of the internal clock of the PC with the browser opened to the input form.
6. Maintenance Using a Web Browser Follow the instructions below to initialize the product using a web browser. (1) Use a web browser to log in to this product. (2) Select “Maintenance” - “Default setting” from the menu. (3) To leave the IP address of the product unchanged without initialization, tick “Do not set IP address to default”. To initialize the IP address, tick “Set IP address to default” and then click “Default”.
7. Troubleshooting 7. Troubleshooting This chapter describes common problems that may occur with this product and what to do about them. If a problem not described here occurs or the same problem occurs after checking the nature of the problem, contact your local authorized dealer. When Communication Fails ■Check wired LAN communication Check the wired LAN communication between this product and the connected PC. - Check that the LAN cable is connected correctly.
7. Troubleshooting ■Check - the peripheral environment and place of installation A nearby source of electromagnetic interference may prevent communication. In general locations (excluding factories) the following may be sources of electromagnetic emissions. - 5GHz band not conforming to IEEE802.11 (when using IEEE802.11a) or 2.4GHz band (when using IEEE802.11b/IEEE802.11g) wireless network - Electronic devices that give off 2.
8. Appendix 8. Appendix BSHardware Setup 1 2 ON Switch 1: OFF Switch 2: OFF Figure 8.1. DIP Switch Initial Setting Table 8.1. Initial Setting List <1/5> Item Default setting Basic setting Host name (No input) DHCP Client Disable, enable IP address (Displayed on the housing sticker on the main unit) Subnet mask 255.0.0.0 Default gateway 0.0.0.0 AP construction Compatibility, integration AP type Normal, master, back up IP address of the master AP 0.0.0.
8. Appendix Table 8.1. Initial Setting List <2 / 5 > Item Channel No. (AP only) Default setting (Depend on the country) See "8.3 List of Country Channels". IEEE802.11a: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps Transmission rate (*1) IEEE802.11b: 11Mbps, 5.5Mbps, 2Mbps, 1Mbps IEEE802.11g: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps, 11Mbps, 5.5Mbps, 2Mbps, 1Mbps IEEE802.11a: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps Transmission rate (Max.
8. Appendix Table 8.1.
8. Appendix Table 8.1. Initial Setting List <4 / 5 > Item Default setting Extended function Bridge Packet Control Network time Access control Disable, enable Function Disable, enable IP address 0.0.0.0 (Disable) Time zone +09:00 TELNET server function Enable, disable FTP server function Enable, disable WEB server function Enable, disable Administrator IP specification Disable, enable Administrator IP address 1-2 0.0.0.
8. Appendix Table 8.1.
8. Appendix Specifications Table 8.2. Specifications <1/2> Item Specification Wired LAN Ethernet standard IEEE802.3(10BASE-T), IEEE802.3u(100BASE-TX) Data transfer speed 10/100Mbps Access method CSMA/CD Communication type Half Duplex, Full Duplex Number of ports 1 (10BASE-T/100BASE-TX) Wireless LAN Transmission IEEE802.11a-compliant OFDM format (Orthogonal Frequency Division Multiplexing) Channel (Depend on the country) See "8.3 List of Country Channels".
8. Appendix Table 8.2. Specifications <2/2> Item Specification Antenna Diversity dipole antenna External Dimensions (mm) 25(W) x 68(D) x 97(H) (Not including antenna and other projecting parts) Weight(g) 250g Table 8.3. List of Country Channels Channel*1 Standard U.S.A. Europe China (NZ2WL- Korea Taiwan (NZ2WL- (NZ2WL-US) (NZ2WL-EU) CN) (NZ2WL-KR) TW) 36, 40, 44, 48, IEEE802.11a 149, 153, 157, 161, 36, 40, 44, 48ch 165ch IEEE802.
8. Appendix External Dimensions 103 SR3.4 φ10 φ9.5 5 18 128.4 5 φ7 25.4 Figure 8.2. External Dimensions (when installed with mounting brackets) Figure 8.3. [mm] Antenna Dimensions Pin Layout of LAN Port 10/100M Table 8.6. Pin Layout of LAN Port 8 ACT 1 LINK Pin No.
WARRANTY Please confirm the following product warranty details before using this product. 1. Gratis Warranty Term and Gratis Warranty Range If any faults or defects (hereinafter "Failure") found to be the responsibility of Mitsubishi occurs during use of the product within the gratis warranty term, the product shall be repaired at no cost via the sales representative or Mitsubishi Service Company.
2. Onerous repair term after discontinuation of production (1) Mitsubishi shall accept onerous product repairs for six (6) years after production of the product is discontinued. Discontinuation of production shall be notified with Mitsubishi Technical Bulletins, etc. (2) Product supply (including repair parts) is not available after production is discontinued. 3. Overseas service Overseas, repairs shall be accepted by Mitsubishi's local overseas FA Center.
R&TTE Directive Compliance with the R&TTE Directive, which is one of the EU directives, has been mandatory for the products sold within EU member states since 1999. To prove the compliance with the R&TTE Directive, manufactures must issue an EC Declaration of Conformity and the products must bear a CE marking. This product is compliant with EN300 328/EN301 893/EN301 489-1,-17/ EN55022/EN55024/EN61000-3-2,-3-3/EN60950-1.
Revisions Print Date March 2011 October 2011 *The manual number is given on the bottom right of the cover.
76 NZ2WL - xxx
