User Manual
Table Of Contents
- Copyright
- Trademarks
- Product Configuration
- Introduction
- Overview
- Operating Mode Descriptions
- Setup
- Settings
- Preparing the Utility Software
- Utility Software Settings
- Setting Descriptions
- To Register or Set Up a New Access Point
- To Edit Settings for an Existing Access Point
- To Use Data scramble Functions for Better Security
- To Use SNMP Agent Functions
- To Use Spanning Tree
- To Access the APL from a Different Router
- Spanning Tree Algorithms (STA)
- What is an STA?
- STA Parameters
- Sample STA Application
- _
- All settings other than bridge priority settings are identical.
- The root bridge is determined by the priority settings of each ...
- The designated bridge for each LAN segment is determined by roo...
- The designated port for each bridge is determined by the design...
- The root port of each bridge is determined by its path cost to ...
- Ports that are neither designated ports nor root ports are back...
- _
- SNMP Agent Functions
- Troubleshooting
- Appendix
- Product Specifications
- Input/Output Interface
- Glossary
- _
- IEEE (Institute of Electrical Electronics Engineers)
- IEEE 802.11/ IEEE 802.11b
- MIB (Management Information Base)
- SNMP (Simple Network Management Protocol)
- Diversity
- Router
- Bridge
- LAN (Local Area Network)
- RSSI (Receive Signal Strength Indication)
- Spectrum diffusion transmission
- DS (Direct Sequence)
- CSMA/CA (Carrier Sense Multiple Access with Collision Avoidanc...
- Hidden Terminal Problem
- RTS (Request to Send)
- Roaming
- Peer-To-Peer
- AP (Access Point)
- User Unit
- ESS ID (Extended Service Set ID)
- Channel
- _
- Index
Setup
FX-DS110-APL
20
Power Supply Connection
There are two ways to connect the APL power supply.
Using the AC adapter provided with the unit
Connect the power adapter to a power outlet, and set the power
switch to 'DC.'
Using a UTP cable (requires the POW-CB10, sold separately)
To receive power from the UTP, set the power switch to 'UTP.'
The cable between the FX-DS110-APL and POW-CB10 should be
a UTP cable with category 5 specifications (maximum 30m).
Using the AC adapter (included)
POWER
WRX
WLINK
LINK
RX
Using a UTP cable
POWER
WRX
WLIN K
LINK
RX
POWER
WRX
WLINK
LINK
RX
HUB
Cross cable *2
Straight cable *1
(max. 30m)
AC adapter
HUB
DC/UTP DC/UTP
PC (NIC)
*1 Operates with the separately available cables TP-03 (3m), TP-05 (5m), TP-10 (10m), TP-20 (20m), TP-50 (50m).
*2 Operates with the separately available TP-X (30cm cross cable and attachment)
Note : The cable length between the unit and PC or hub should not exceed 90m.
UP LINK 8X 7X 6X 5X 4X 3X 2X 1 X
Straight cable *1
Straight cable *1
POW-CB10
IN Data OUT
IN
AC adapter
UP LINK 8 X 7 X 6X 5X 4X 3X 2X 1X
IN Data OUT
IN
Figure 4.6. Power Supply Connection
Notes!
Never use any AC adapter other then listed below. Unauthorized
adapters may cause damage or accidents due to overheating.
･
If the cable length between APL and POW-CB10 is between 10
and 30m, use the AC adapter supplied with the POW-CB10.
･
If the cable length between APL and POW-CB10 is 10m or less,
use the AC adapter supplied with the FX-DS110-APL.