User Manual
Table Of Contents
- Copyright
- Trademarks
- Product Configuration
- Introduction
- Overview
- Operating Mode Descriptions
- Setup
- Settings
- Preparing the Utility Software
- Utility Software Settings
- Setting Descriptions
- To Register or Set Up a New Access Point
- To Edit Settings for an Existing Access Point
- To Use Data scramble Functions for Better Security
- To Use SNMP Agent Functions
- To Use Spanning Tree
- To Access the APL from a Different Router
- Spanning Tree Algorithms (STA)
- What is an STA?
- STA Parameters
- Sample STA Application
- _
- All settings other than bridge priority settings are identical.
- The root bridge is determined by the priority settings of each ...
- The designated bridge for each LAN segment is determined by roo...
- The designated port for each bridge is determined by the design...
- The root port of each bridge is determined by its path cost to ...
- Ports that are neither designated ports nor root ports are back...
- _
- SNMP Agent Functions
- Troubleshooting
- Appendix
- Product Specifications
- Input/Output Interface
- Glossary
- _
- IEEE (Institute of Electrical Electronics Engineers)
- IEEE 802.11/ IEEE 802.11b
- MIB (Management Information Base)
- SNMP (Simple Network Management Protocol)
- Diversity
- Router
- Bridge
- LAN (Local Area Network)
- RSSI (Receive Signal Strength Indication)
- Spectrum diffusion transmission
- DS (Direct Sequence)
- CSMA/CA (Carrier Sense Multiple Access with Collision Avoidanc...
- Hidden Terminal Problem
- RTS (Request to Send)
- Roaming
- Peer-To-Peer
- AP (Access Point)
- User Unit
- ESS ID (Extended Service Set ID)
- Channel
- _
- Index
Setup
FX-DS110-APL
19
Table Top Installation
Use the rubber pads included with the unit.
To install on a table top, choose a sturdy, level surface with a
well-ventilated space (approx. 5 cm.) in all directions. Wireless
equipment has a larger sending and receiving range when it is in a
highly visible location. Choose a location where the sight lines
are as clear as possible.
Note!
Do not obstruct the ventilation slits. This can cause the
temperature inside the product to rise and can damage the
components inside.
Cable Installation
Connect the UTP connector to the UTP cable.
Notes!
･ When connecting this product to a personal computer or hub use
a twisted pair cable no more than 100m in length.
･ Use UTP cable having category 3, 4, or 5 specifications. (If using
a 10BASE-T power supply, use a UTP cable with category 5
specifications.)
･ When connecting with a personal computer (NIC) or hub up-link
port, use a UTP cross cable (TP-X).
･ When connecting with a hub (other than up-link port), use a UTP
straight cable.
POWER
WRX
WLINK
LINK
RX
POWER
WRX
WLINK
LINK
RX
*1 Operates with the separately available cables TP-03 (3m), TP-05 (5m), TP-10 (10m), TP-20 (20m),
TP-50 (50m), TP-100 (100m)
*2 Operates with the separately available TP-X (30cm cross cable and attachment)
Note : The cable length between the unit and PC or hub should not exceed 100m.
POWER
WRX
WLINK
LINK
RX
PC (NIC)
HUB
UPL INK 8X 7X 6 X 5X 4X 3X
2X 1 X
Cross cable *2
Up-Link port
Normal port (not Up-Link port)
POWER
WRX
WLINK
LIN K
RX
HUB
UPLI NK 8X 7X 6 X 5X 4X 3X
2X 1X
Straight cable *1
Figure 4.5. Cable Connection