Contec CMS-08A Blood Pressure Monitor Electronic Sphygmomanometer ■ To assure the correct use of the product safety measures, please carefully read user manual before using. ■ After reading, please validly keeping to refer and consult at any moment. Medical Test Supply www.medicaltestsupply.
Contents Chapter1 Safety Precautions: ....................................................................................................... 1 Chapter2 Main Unit ..................................................................................................................... 3 Chapter3 Button Functions .......................................................................................................... 4 Chapter4 External Interfaces .................................................................
Chapter1 Safety Precautions: Before use, carefully read "Safety Precautions" for a correct use. To prevent users suffered hurt or dandification due to improper use, see "Safety Precautions", and use this product properly. For safety reasons, be sure to comply with safety precautions. Note If not to use correctly, it exists that a potentially hazardous situation which may result in injury to the user or patient or damage to the equipment or other property.
. Operation for battery Note Please use 4 "AA" size manganese or alkaline batteries, do not use batteries of other types. Otherwise it may cause fire. New and old batteries, different kinds batteries cannot be confusion. Otherwise it may cause battery leakage, heat, rupture, and damage to Electronic Sphygmomanometer. + and - polarities of the batteries must match the polarities of the battery compartment as indicated. When the batteries power exhausts, replace with four new batteries at the same time.
Chapter2 Main Unit The product is in the package. Open the package and confirm whether the product is whole. Display Cuff Plug Cuff Air Plug UP/DOWN Button MEMORY Button AC Adapter Jack MENU Button USB Plug Jack USER SWITCH Button ON/OFF Button Accessories： START/STOP Button Adult Cuff Dry Battery (Specification: limb circumference 22-32cm (middle part of upper arm), please choose suited cuff when measuring pediatric or other).
Chapter3 Button Functions All the operations to the Electronic Sphygmomanometer are through the buttons. The names of the buttons are above them. They are: 【ON/OFF】 】 Hold the button to start or close the device. 【START/STOP】 】 Press to inflate the cuff and start a blood pressure measurement. When measuring, press to cancel the measurement and deflate the cuff.
Chapter5 Dry Battery/AC Adapter Installation The product can use dry battery or AC adapter as power source. 5.1 Dry Battery Installation ① Press the▲indicator on the battery cover and slide the cover off in the direction of the arrow. ② Install 4 "AA" size dry batteries so the +(positive) and 一(negative) polarities match the polarities of the battery compartment as indicated. ③ Replace the battery cover. Icon “ ”: the batteries power will exhaust.
You'd better take off batteries when use the AC adapter as power source. If there is any damage to the AC adapter, you should use batteries to run the device. When adapter and batteries are both used at the same time, the battery power will not be consumed. Switch adapter and battery as power supply when the device is off, otherwise, the device may shutdown due to power failure. Chapter6 Setting The Date And Time It is necessary to set date and time after turning on the device.
Note Please choose the computer which should be ensured compliance with the requirements of IEC60950, or else it may damage the device. Chapter7 Unit There are two units: "mmHg" and "kPa". The default is: "mmHg". To switch "mmHg" and "kPa" units, enter the 【SYSTEM SETUP】 submenu in 【SYSTEM MENU】, and complete switching in 【UNIT】 item. Chapter8 User Switch The Electronic Sphygmomanometer stores the measure results of three users automatically, and up to 100 items for every user.
Carry out the operation in a room with comfortable temperature. When measuring, take the thick clothes off instead of rolling up the sleeves. In order to measure accurately, pay attention to applying the cuff properly (left arm). ① Make sure the air plug is securely inserted in the main unit. ② Stretch cuff into a barrel for the arm can conformable enter into the barrel. ③ Arm penetrate through the cuff, the air tube of the cuff will pass the top of your palm. ④ Apply the cuff to your upper arm.
Chapter10 BP Measurement 10.1 Accurate Measurement Way Measurement in quiet and relaxing state. 1. Place your arm on a table. 2. The cuff is level with your heart. 3. The palm of the hand is up, and the body relax. Try to measure your blood pressure at the same time each day with the same arm and the same pose for consistency. The high and low location of cuff will cause changes in measurement results. Do not touch Electronic Sphygmomanometer, cuff or windpipe during measurement.
Note Wait 4-5 minutes between measurements The arm may have congestion following a measurement which may cause incorrect blood pressure readings. After the blood flow is re-established, take a measurement once again. When some factors affect the measurement results in measurement process, error messages hints will appear on the screen, you can obviate the malfunction and restart a measurement.
3. Press 【LIST】 button to switch to data table interface. 4. Press 【TREND】 button to display trend interface. 5.Finish displaying the measurement values Press 【EXIT】 to return the main interface or hold 【ON/OFF】 button to turn the power off. *The device will automatically turn off after two minutes in which there is no operation to the device, even if you forget to turn the power off. 11.
*The device will automatically turn off after two minutes in which there is no operation to the device, even if you forget to turn the power off. Chapter12 Alarm Function Alarms are classified into two categories: technical alarm and physiological alarm.
Note ◎Make sure the nail covers the light window. ◎The wire should be on the backside of the hand. ◎SpO2 value is always displayed in the fixed place. Medical Test Supply 13 www.medicaltestsupply.
Warning ◎Check if the sensor cable is in normal condition before monitoring. After unplugging the SpO2 probe cable from the socket, the interface will return. ◎Do not use the SpO2 probe once the package or the sensor is found damaged. Instead, you shall return it to the vendor.
Measurement Limitations During operation, the accuracy of oximeter readings can be affected by: High-frequency electrical noise, including noise created by the host system, or noise from external sources, such as electrosurgical apparatus connected to the system. Intravascular dye injections. Excessive patient movement. External light radiation. Improper sensor installation or incorrect contact position of the patient. SpO2 probe temperature (optimal temperature between 28°C and 40°C).
Chapter16 Installation Of The Software 16.1 Host Requirements Pentium IV 1.8G or more Operation System:Windows XP EMS memory: 256M or more Hard Disk: 40G or more Display: 17 inch or more CD-ROM USB: 2 or more Resolution of printer: 600 DPI 16.2 Installation of Software 1.Place the CD-ROM in the CD-ROM compartment located on your computer. 2.If Auto Play for CDs is enabled, place CD in reader and follow instructions when they appear in the screen; otherwise follow install instructions below: 1.
Chapter17 Keys And Symbols Signal Description Warning – See User Manual SYS Systolic pressure MAP MAP pressure DIA Diastolic pressure PR Pulse rate (bpm) ADU Adult PED Pediatric NEO Neonatal INFO Information Open the alarm sound indication Close the alarm sound indication Low-power Full-power 1.no NIBP data to review 2.no finger inserted to SpO2 probe 3.
Chapter18 Error Message Error message will be displayed in the screen if there is something wrong when measuring. The causes and solutions are shown as follows: Error Message Causes Solutions Function abnormal Please contact us Self-test failure System failure Cuff is not connected Loose cuff Correctly connect cuff (refer to 8 page) correctly.
Chapter19 TROUBLESHOOTING Abnormal Phenomenon’s BP measurement values too high or too low. No pressure Cuff deflates short time in Causes Solutions Cuff is not connected correctly.
Switch on the power once again and restart an operation. Replace the batteries. If no, please contact us. Other phenomenon Medical Test Supply 20 www.medicaltestsupply.
Chapter20 Clean And Maintenance *Please follow the instructions in the user manual. If you do not comply, our company will not assume responsibilities for the products quality. Frequently clean the Electronic Sphygmomanometer. If there is something dirty on the device, clean it with a soft dry cloth. If the unit is particularly dirty, you can clean it with a soft cloth dampened with water or neutral detergent after the cloth can be full twisted. Warning Do not submerge the device in water.
In addition, the overall check of the Sphygmomanometer, including the NIBP calibration and safety check such as the leakage current, should be only performed by qualified personnel once every 12 months. Warning The disposal of scrap instrument and its accessories and packing (including batteries, plastic bags, foams and paper boxes) should follow the local laws and regulations.
Chapter21 NIBP Specification Name Electronic Sphygmomanometer Display 2.8'' color LCD Display NIBP Specifications Measurement Method Oscillometric method Working modes Automatic Measurement Range Pressure adult 0~290mmHg（0~38.6kPa） pediatric 0~235mmHg（0~31.3kPa） neonatal 0~140mmHg（0~18.
Accessories Medical Test Supply Standard Configure: Adult Cuff: limb circumference 22-32cm (middle of upper arm ) Software CD, User Manual, USB data line, four "AA" alkaline batteries Separate Sale: Pediatric Cuff: limb circumference 10-19cm (middle of upper arm ) Neonatal Cuff: limb circumference 6-11cm (middle of upper arm ) AC Adapter Input: AC 100-240V 50-60Hz AC 500mA Output: DC 6.0V 1.0A 24 www.medicaltestsupply.
Chapter22 SpO2 Specification Name SpO2 Probe (Accessory Separate Sale) Model Y10UCH150 Measurement Range SpO2 Measuring Range: 0%~100%; Pulse Rate Measuring Range: 30bpm~250bpm; Resolution SpO2 1% PR 1bpm Measurement Accuracy SpO2, PR 70%~100% ±2% 0%~69% undefined ±2bpm or ±2% (select larger) Measurement Performance In Weak Filling Condition pulse-filling ratio 0.4% : SpO2 error ±4%, pulse rate error ±2bpm or ±2% (select larger) Optical Sensor Red light wavelength is 660nm, 6.
