HQ 2SHUDWLQJ LQVWUXFWLRQV
$ % & 5HVHW VHF 6WDUW 5HVHW VHF
en Table of contents 8 Intended use . . . . . . . . . . . . . . . ( Safety instructions . . . . . . . . . . Before you switch ON the appliance Delivery. . . . . . . . . . . . . . . . . . . . . . . Installation. . . . . . . . . . . . . . . . . . . . . In daily use . . . . . . . . . . . . . . . . . . . . Door lock . . . . . . . . . . . . . . . . . . . . . Button lock . . . . . . . . . . . . . . . . . . . . Damage . . . . . . . . . . . . . . . . . . . . . . Disposal . . . . . . . . . . . . . . . . . . . . .
en Intended use 2 Cleaning and maintenance . . . Overall condition of the machine Special salt and rinse aid . . . . . . Filters . . . . . . . . . . . . . . . . . . . . . Spray arms . . . . . . . . . . . . . . . . . 3 Fault, what to do? . . . . . . . . 25 . 25 . 25 . 26 . 26 8 Intended use dnentI This appliance is intended for use in the home and the home environment. Use the dishwasher only in the household and only for its designed purpose: for washing domestic dishes. . . . . . . . . . .
Safety instructions Delivery 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier. 2. Please dispose of the packaging material in an environmentally friendly manner. 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
en Safety instructions If you cannot obtain any information from the manufacturer, you must not install the dishwasher above or below these appliances. If you install a microwave oven above the dishwasher, the microwave oven may be damaged. Install built-under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability.
Safety instructions Deactivating the button lock: Hold down the button + for approx. 4 sec. until the display ’– goes out. When the programme ends (‹:‹‹ on the digital display), the button lock is cancelled. If there is a power failure, the button lock is retained. Whenever a programme is restarted, the button lock must be reactivated. Damage The appliance may be repaired and opened up by a technician only. To do this, disconnect the appliance from the power supply.
en Safety instructions m Warning Risk of scalding! Open the door carefully when the programme is still running. There is a risk of hot water spraying out of the appliance. m Warning Risks to children! If fitted, use the childproof lock. An exact description can be found in the back of the enve lope. Do not allow children to play with or operate the appliance. Keep children away from detergents and rinse aid. These may cause chemical burns in the mouth, throat and eyes or asphyxiation.
Protection of the environment 7 Protection of the * Getting to know your environment onitceotPr het of Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. Please dispose of the individual parts separated according to type. Please ask your dealer or inquire at your local authority about current means of disposal. Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g.
Water softening system/Special salt en Appliance interior 1" Interior light * 1* Top basket 12 Knife shelf * 1: Tablet collecting tray 1B Upper spray arms 1J Bottom spray arm 1R Dispenser for special salt 1Z Filters 1b Cutlery basket 1j Bottom basket 9" Dispenser for rinse aid 9* Detergent dispenser 92 Lock for detergent dispenser 9: Rating plate * depending on model Overview of menu The settings can be found in the individual chapters.
Water softening system/Special salt To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of •:‹ˆ has been reached, the display jumps back to •:‹‹ (off). 2. Press START button P. The chosen setting has now been stored.
en Rinse aid Switching off salt refill indicator/water softening system 1. Open the dispenser 9" by pressing and lifting the plate on the cover. Switchingof watersofteni gsy tem If the salt refill indicator ` is impaired (e.g. when using combined detergents containing salt component), it can be switched off. Proceed as described under “Adjusting the water softening system” and set the value to •:‹‹. The water softening system and salt refill indicator are now switched off.
Utensils 3. Hold down programme button # and press START button P until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value §:‹… is indicated on the digital display )". To change the setting: 1. Press programme button 3.
en Utensils Loading the dishwasher Cups and glasses 1. Remove large food remnants. It is not necessary to prerinse utensils under running water. 2. Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down. – parts with curves or indentations are at an angle, thereby allowing water to drain. – they do not obstruct rotation of the spray arms 1B and 1J. Very small utensils should not be washed in the machine, as they may fall out of the baskets.
Utensils en Pans Cutlery basket Bottom basket 1j You should always place cutlery unsorted with the points downwards. To prevent injuries, place long, pointed implements and knives on the knife shelf. Tip Heavily soiled utensils (pans) should be placed in the bottom basket. The more powerful spray jet provides a better dishwashing result. Tip Other examples, such as the best way of loading your dishwasher, can be found on our homepage as a free download.
en Utensils Small accessories holder * Smal ac es oriesholder * depending on model Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder. Adjusting the height of the basket * Adjustingtheheightofthebasket * depending on model If required, the height of the upper utensils basket 1* can be adjusted to provide more space for tall utensils either in the upper or lower basket. Appliance height 81.5 cm Top basket Setting 1 max. ø Setting 2 max.
Detergent 3. To raise the basket, hold the basket on the sides of the upper edge and lift it up. 4. Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit. Top basket with upper and lower roller pairs 1. Pull out the top basket 1* out. 2. Remove the upper basket and reattach it to the upper (stage 3) or lower (stage 1) rollers. en .
en Detergent Adding detergent 1. If the detergent dispenser 9* is still closed, press the lock 92 to open the detergent dispenser. Pour detergent into the dry detergent dispenser 9* only (insert tablet flat, not on its edge). Dosage: see manufacturer’s instructions on the packaging. The graduated detergent dispenser 9* helps you add the correct amount of powder or liquid detergent. Usually 20 ml–25 ml are adequate for normal soiling. If using tablets, one tablet is adequate. PO PO PO 2.
Detergent en Notes You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately. If programmes are short, tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue. It is recommended to use washing powder for these programmes. The Intensive programme (on some models) requires one tab only.
en Overview of programmes / Overview of programmes m aogrm prseofw eviO rve The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options en § Half load * Half oad Programme selection If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. You can select a suitable programme according to the type of utensils and degree of soiling.
en Operating the appliance 1 Operating the appliance ngitaO rpe Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations. Aqua sensor * Aquasensor * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
Operating the appliance Timer programming * Timerprogram ing en Automatic switch off after end of programme or interior light* Automaticswitchof /interiorlight * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Close the door. 2. Switch on ON/OFF switch (. 3. Press button @ + until the digital display )" jumps to œ:‹‚. 4. Press @ + or – button until the displayed time corresponds with your requirements. 5.
en Operating the appliance To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ˜:‹ƒ has been reached, the display jumps back to ˜:‹‹. 2. Press START button P. The set value is saved. Switching off the appliance Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down.
Cleaning and maintenance To change the setting, 1. Press the button 3 to switch the Intensive drying on š:‹‚ or off š:‹‹. 2. Press START button P. The set value is saved. 2 Cleaning and maintenance ngniaeCl nda encaentm ia Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate.
en Cleaning and maintenance Filters Spray arms The filters 1Z keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system.
Fault, what to do? 3 Fault, what to do? ,tF ula w tha ot Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
en Fault, what to do? Fault table Fault “Check water supply” display X lights up. Error code “:‹ˆ is lit. Error code “:‚ƒ is lit. Error code “:ƒƒ is lit. Error code “:ƒ… is lit. Error code “:ƒ† is lit. Error code “:ƒˆ is lit. 28 Cause Supply hose kinked. Tap turned off. Tap jammed or calcified. Remedial action Install supply hose without kinks. Turn the tap on. Turn the tap on. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked.
Fault, what to do? Fault A different error code is indicated on the digital display. (“:‹‚ to “:„‹) Cause A technical fault has probably occurred. Display flashes. Door not closed properly. Refill indicator for salt ` No rinse aid. and/or rinse-aid h is lit. No salt. Sensor does not detect salt tablets. Refill indicator for salt ` Refill indicator switched off. and/or rinse-aid h is not lit. There is still enough special salt/ rinse aid available.
en Fault, what to do? Fault Utensils not dry. Cause No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the utensils and cutlery. The combined detergent used has a poor drying performance Remedial action Refill rinse aid. Select programme with drying (see “Overview of programmes”, “Programme sequence”). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible.
Fault, what to do? Fault Food remnants on the utensils. Cause Utensils placed too closely together, utensils basket overfilled. Spray arm rotation obstructed. Spray arm nozzles are blocked. Filters 1Z dirty. Filters 1Z inserted incorrectly and/or not engaged. Rinse programme too weak. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed. Tall narrow receptacles in corner areas are not rinsed adequately. Detergent residue.
en Fault, what to do? Fault Water stains on plastic parts. Remedial action Use a more intensive programme (more water changes). Arrange utensils in a sloping position. Use rinse aid. If required, increase softening setting. Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container or deposited. These coatings cannot Clean appliance mechanically. on the door. usually be removed with chemicals (appliance cleaner, ...).
Fault, what to do? Fault Coloured (blue, yellow, brown), difficult to remove to non-removable coatings in the appliance or on stainless steel utensils. Coloured (yellow, orange, brown), easily removable deposits inside the appliance (mainly in the floor area) Plastic parts discoloured. Removable streaks on glasses, glasses with metallic appearance and cutlery. Initial or existing, irreversible clouding of glass. Cause Film formation consisting of ingredients from vegetables (e.g.
en Fault, what to do? Fault Rust spots on the cutlery. Appliance does not start. Programme starts automatically. The door is difficult to open. Door cannot be closed. Cover on the detergent dispenser cannot be closed. Detergent residue in the detergent dispenser or in the tablet collecting tray. 34 Cause Cutlery not adequately rustresistant. Knife blades are frequently more severely affected.
Fault, what to do? Fault Appliance stops in the programme or programme is interrupted. Filling valves making striking noises. Knocking or rattling noise. Unusual foam formation. Cause Door not closed properly. Do not place utensils or fragrance dispenser in the tablet collecting tray. Top basket presses against the door and prevents door from being closed securely. Power and/or water supply interrupted. Depends on domestic installation, as appliance is not defective. No effect on appliance function.
Customer service en 4 Customer service om C treus 5 Installation and connection ecvires If you are unable to rectify the fault, please contact your customer service. We always find a suitable solution, even to avoid unnecessary visits by technicians. Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list. When calling, please state the appliance number (ENr.
Installation and connection en Delivery Installation Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle. The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor.
en Installation and connection Drinking water connection Warm water connection * 1. Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts. Ensure that the drinking water connection is not kinked, crushed or twisted. 2. When replacing the appliance, always use a new water supply hose. Water pressure: At least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
Installation and connection Electrical connection Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 9:. The socket must be near the appliance and freely accessible following installation.
en Installation and connection Transportation Protection against frost Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1. Turn on the tap. 2. Close the door. 3. Switch on ON/OFF switch (. 4. Select programme with the highest temperature. The expected programme duration is indicated on the numerical display )". 5. Press START button P. Programme sequence starts. 6. After approx.
&KLOGSURRI ORFN GRRU ORFN :DUQLQJ $FWLYDWH WKH FKLOGSURRI ORFN 2SHQ WKH GRRU ZLWK DFWLYDWHG FKLOGSURRI ORFN 'HDFWLYDWH FKLOGSURRI ORFN $OZD\V FORVH WKH DSSOLDQFH GRRU FRPSOHWHO\ ZKHQ \RX OHDYH WKH DSSOLDQFH 7KLV LV WKH RQO\ ZD\ \RX FDQ SURWHFW \RXU FKLOGUHQ IURP SRWHQWLDO GDQJHUV %DNLQJ VKHHW VSUD\ KHDG /DUJH VKHHWV RU JULOOHV DQG SODWHV ZKLFK KDYH D GLDPHWHU JUHDWHU WKDQ FP JRXUPHW SODWHV SDVWD SODWHV GLQQHU SODWHV FDQ EH FOHDQHG ZLWK WKH DLG RI WKH VSUD\ KHDG 7R G
$48$ 6723 JXDUDQWHH HQ GRHV QRW DSSO\ WR DSSOLDQFHV ZLWKRXW $TXD 6WRS ,Q DGGLWLRQ WR ZDUUDQW\ FODLPV DJDLQVW WKH VHOOHU EDVHG RQ WKH SXUFKDVH FRQWUDFW DQG LQ DGGLWLRQ WR RXU DSSOLDQFH ZDUUDQW\ ZH ZLOO SD\ GDPDJHV XQGHU WKH IROORZLQJ FRQGLWLRQV ,I RXU $TXD 6WRS V\VWHP LV GHIHFWLYH DQG FDXVHV ZDWHU GDPDJH ZH ZLOO PDNH JRRG WKH GDPDJH IRU SULYDWH XVHUV 7R HQVXUH ZDWHU GDPDJH SURWHFWLRQ WKH DSSOLDQFH PXVW EH FRQQHFWHG WR WKH SRZHU VXSSO\ 7KLV OLDELOLW\ JXDUDQWHH LV YDOLG IRU WKH VHUYLFH OLIH R
