User`s guide

11
User’s Guide
User’s Guide
To assign the outputs of the current bank of channels:
• Press the ASSIGN button [10] to enter Assign
Mode. The ASSIGN LED should be flashing.
• Press the OUTPUT button [12] to select channel
outputs for assignment. The current channel
output settings will appear on the LCD.
• Use the V-Pots to adjust the outputs of the
channels and press the ASSIGN button to
apply the changes and exit assignment mode.
To assign a send destination:
• Select the send whose destination you want to
edit (see SEND button for further details).
• Press the ASSIGN button [10] to enter Assign
Mode. The ASSIGN LED should flash and the
destination of the selected send on the
current channels appears on the LCD.
• Use the V-Pots to adjust the send destinations
of the channels and press the ASSIGN button
to apply the changes and exit assignment mode.
[11] INPUT
• Pressing the INPUT button causes the
channel strips’ input sources to be displayed
on the LCD while the button is held down.
• When used in combination with the ASSIGN
button [10], the Input sources can be modified
from the LCD (see ASSIGN).
[12] OUTPUT
• Pressing the OUTPUT button causes the
channel strips’ output settings to be displayed
on the LCD while the button is held down.
• When used in combination with the ASSIGN
button [10], the Output settings can be
modified from the LCD (see ASSIGN).
FADER BANKS
BANK
CHANNEL
ASSIGNMENT
PLUG-INS
PAN
SENDS
I/O
EQ DYN
EIGHT CHANNEL MASTER CONTROL
F1 F2 F3 F4 F5 F6 F7 F8
F9 F10 F11 F12 F13 F14 F15 F16
DISPLAY
SMPTE
BEATS
NAME
VALUE
FADER BANKS
BANK
CHANNEL
SEND
ASSIGN
PLUG-IN
PAN
INPUT
EDIT TRANSPORT MEM LOC ALT VIEW CUT SEPERATE PASTEMIX
CLEAR
PEAKS
METERS
READ TOUCH LATCH TRIM OFF AUTOWRITE
SEND A SEND C SEND D SEND E SHIFT SND MUTE
DEFAULT
PLUG-IN
ASSIGN
COMPARE BYPASS
SEND B
OUTPUT
VIEW METERS
[13] SEND
The SEND button is used in combination with the
Automation/Send buttons to set the V-Pot function
to a particular Send level. While the SEND button is
pressed and held, the Automation/Send buttons
change to the alternate functions labeled below the
buttons. Hold down the SEND button and press one
of these buttons to access the function:
• SEND A [28]: Changes the V-Pot function to
Send A level. The ASSIGNMENT display changes
to show “SA” to denote that Send A is active.
• SEND B [29]: Changes the V-Pot function to
Send B level. The ASSIGNMENT display changes
to show “SB” to denote that Send B is active.
• SEND C [30]: Changes the V-Pot function to
Send C level. The ASSIGNMENT display changes
to show “SC” to denote that Send C is active.
• SEND D [31]: Changes the V-Pot function to
Send D level. The ASSIGNMENT display changes
to show “SD” to denote that Send D is active.
• SEND E [32]: Changes the V-Pot function to
Send E level. The ASSIGNMENT display changes
to show “SE” to denote that Send E is active.
• SHIFT [33]: Swaps the V-Pot and fader
functions. Faders control the send level, while
the V-Pots control the Send Pan (if available).
The ASSIGNMENT display changes to show
“FP” to indicate the flipped status. To exit SHIFT
mode, simply press the SEND + SHIFT combo
again and the previous status will be restored.
• SND MUTE [34]: Activates Send Mute Mode
for the V-Pots. When Send Mute Mode is
active, the LED next to the SEND button
flashes, and the ASSIGNMENT display
indicates the current send. Pressing V-SEL
and a channel’s V-Pot mutes the active send
on that channel when Send Mute Mode is
active. Press one of the key combos described
above to select a different send to operate on.
To exit Send Mute mode, simply press the
SEND + SND MUTE combo again, and the
previous status will be restored.