Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board User Manual Connect Tech Inc. 42 Arrow Road Guelph, Ontario N1K 1S6 Tel: Toll: Fax: Email: Web: 519-836-1291 800-426-8979 (North America only) 519-836-4878 sales@connecttech.com support@connecttech.com www.connecttech.com CTIM-00060 Revision 0.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Table of Contents Customer Support Overview .......................................................................................................................... 4 Contact Information........................................................................................................................................ 4 Limited Lifetime Warranty ...........................................................
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Battery..................................................................................................................................................................... 24 Description ....................................................................................................................................................24 Connector & LEDs .......................................................................................
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Customer Support Overview If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties. In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Limited Lifetime Warranty Connect Tech Inc. provides a Lifetime Warranty for all Connect Tech Inc. products. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Introduction Xtreme/SBC PCI-104 Single Board Computer Connect Tech’s Xtreme/SBC PCI-104 Single Board Computers offer a variety of embedded processor options including Intel Atom, Freescale i.MX51, TI OMAP and NVIDIA Tegra.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual System Block Diagram The Qseven module implements the core processing features including: processor, memory, and system physical interfaces via the southbridge. Many of the Qseven modules are based on the mobile Intel Atom architecture (Z series processor + Poulsbo / SCH US15W chipset); shown in the block diagram below. This document will generally refer to the features of the US15W. Revision 0.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Hardware Description Connector Locations Xtreme/SBC PCI-104 – Top Xtreme/SBC PCI-104 – Bottom Connector Summary Location Connection P1 Q7 P2 PCI-104 Jumper Function P3A, P3B USB J1 PS/2 power P4 GBE J2 Fan Power P5 VGA J3 Fan PWM polarity P6 ATX Power J4 LVDS panel power P7 LVDS Video P8 LVDS Backlight J5 LVDS backlight enable polarity J6 LVDS Backlight Power P9 RS232 serial
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Qseven Module Interface Description The processor and Chipset are implemented on the Qseven CPU module, which connects to the Xtreme/SBC PCI-104 via a MXM connector. As previously mentioned, many of the existing Qseven Modules use the Intel Atom mobile architecture, Z series processor + Poulsbo / SCH US15W chipset. The Xtreme/SBC PCI-104 implements a subset of the Qseven features, as describe in the introduction.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual LVDS Description The Xtreme/SBC PCI-104 provides dual 18 or 24 bit LVDS display channels via P7, which are connected directly from the Qseven module . LVDS panel supply power is selected with jumper J4 and backlight power is selected with jumper J6. Both are current limited to 500 mA. US15W: The US15W provides only a single 18 or 24 bit display channel.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Function LVDS backlight power Location P8 Type Hirose DF13-8P-1.25H connector Pinout Pin Signal Description 1 +12V +12 V DC, max. 1A 2 +12V +12 V DC, max. 1A 3 +5V +5 V DC, max. 1A 4 +5V +5 V DC, max. 1A 5 LVDS_BLEN Backlight enable, level selected with J4 6 VCC_BKL Back light power, selected with J6 7 GND Digital ground 8 GND Digital ground Function LVDS backlight power select Selects either +12V or +5V.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Function LVDS backlight enable polarity Selects either positive or negative. Refer to the inverter power supply documentation for proper configuration. Location J5 Type 1x2 2mm jumper block Pinout Default 12 Position Description off Positive polarity on Negative polarity Positive polarity Revision 0.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Gigabit Ethernet Description The gigabit Ethernet interface’s controller (MAC + PHY) is implemented on the Qseven module, while the Xtreme/SBC PCI-104 provides the necessary magnetics and termination. Most Qseven modules support 1000BASE-T, 100BASE-TX, and 10BASE-T standards with either a Realtek 8111 or Intel 82574 PCIe Ethernet controller.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual USB 2.0 Description The Xtreme/SBC PCI-104 implements 4 of the 8 available USB 2.0 connections via two connectors. Over current protection and power supply filtering is provided. Only the USB host features of the Qseven specification have been implemented, USB client features are not supported. Connector Function USB 2.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual SATA Description The Xtreme/SBC PCI-104 provides 2 SATA host connections. US15W: Most Qseven modules based on the US15W, convert the US15W’s IDE interface to one SATA connection (as IDE master) and one built-in NAND based flash drive (as IDE slave). Consult the Qseven module’s documentation for more information.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual PCI-104 Description The Xtreme/SBC PCI-104 allows up to 4 PCI-104 add-on boards to be installed in a “stack up” configuration. The PCI-104 connected through a PCIe to PCI bridge which is attached the first x1 PCIe lane of the Qseven connector. Note: The Xtreme/SBC PCI-104 provides 3.3V generated from the +5V input power. The entire +3.3V rail on the PCI-104 stack is limited to 4A.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual LPC Super I/O The Xtreme/SBC PCI-104 implements many low speed legacy I/O features with the SMSC SCH3114 Super I/O, which is connected to the Qseven module via the LPC (Low Pin Count) bus. This Super I/O device provides 4 serial ports, 2 PS/2, and many other status / control features. Note: the Qseven specification states that all Qseven modules BIOS implementations must support either the Winbond W83627 or SMSC SCH3114.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Connectors Function RS232 x2 Locations P9 Type 2x10 2mm header Pinout Function Pin Signal Pin Signal 1 DCD1 2 DSR1 3 RXD1 4 RTS1 5 TXD1 6 CTS1 7 DTR1 8 RI1 9 GND 10 N/C 11 DCD2 12 DSR2 13 RXD2 14 RTS2 15 TXD2 16 CTS2 17 DTR2 18 RI2 19 GND 20 N/C RS485 x2 Locations P11 Type Pinout 18 2x10 2mm header Pin Signal Pin Signal 1 RXD0+ 2 N/C 3 TXD0+ 4 N/
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual PS/2 Keyboard and Mouse Description A PS/2 keyboard and PS/2 mouse interface are provided via P13; where the PS/2 voltage is selectable with J1. Refer to the specification printed on the bottom of the keyboard and mouse to determine which voltage to select; in most cases this is 5V.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Power Description The Xtreme/SBC PCI-104 is designed to be powered from an ATX type power supply, and support many of the ACPI features like suspend to RAM. A CR1225 battery holder (P16) provides the VBAT for the Qseven module. The Xtreme/SBC PCI-104 generates 3.3V on board, to facilitate alternate powering options.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Connectors & Jumpers Function ATX input power Location P6 Type Pinout JST B15B-EH-A Pin Signal Description 1 +5V +5V input, powers onboard power regulators & Qseven module 2 GND Digital Ground 3 +5V +5V input, powers onboard power regulators & Qseven module 4 GND Digital Ground 5 +5V +5V input, powers onboard power regulators & Qseven module 6 +5V_SB +5V standby input, powers +3.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Function Power Supply on Selects either PS_ON# signal from Qseven module or always on Location J8 Type 1x3 2mm Pinout Position Description 1-2 Always on 2-3 Qseven PS_ON# off floating Default Qseven PS_ON# Function Power Button Use to connect a momentary push button to the Qseven PWR_BTN# signal.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Fan Control Description If actively cooling is required; P14 can be used to power and control a fan with J2 selecting the fan voltage. Connectors & Jumpers Function Fan power/control Location P14 Type JST B15B-EH-A connector Pinout Pin Signal Description 1 FAN_SPEED 2 FAN_PWR Fan power selected by J2 3 FAN_GND Filtered digital ground Speed signal Function Fan power Selection Selects either +5V or +12V.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Battery Description A CR1225 battery holder is provided at P16. This is a standard 3V battery, which powers the RTC (real time clock) on the CPU module. In most cases, it is not required to preserve critical BIOS settings as most Qseven modules have a flash based BIOS. Connector & LEDs Function Battery Location P16 Type CR1225 battery holder 24 Revision 0.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Hardware Installation 1. Ensure all external system power supplies are off. 2. Install the Qseven module into P1. Be sure to follow the manufacturer’s direction for proper heatsink/heatspreader installation. 3. Verify all jumper settings from the relevant sections, paying special attention the power selection jumpers 4.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer & PCI-104 Qseven Carrier Board - User Manual Software Installation & Configuration In general, always refer to the Qseven module’s manual for proper installation of drivers and configuration software; as well as for appropriate BIOS settings. The following sections provides some specific notes and hints for successful module integration Operating System Notes Linux General PS/2: Add kernel option i8042.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Cables & Interconnect The following table summarizes the Xtreme/SBC PCI-104’s headers and lists the matching cables included with the optional cable kit CKG001. Location PCB Connector Cable Part Number Drawing Description PCB End Interface End Number Hirose P3A, P3B Hirose CBG071 CTIC-00182 USB (dual) DF13-8P-1.25H(50) USB 2.0 Type A female DF13A-8S-1.
Dimensions Dimension Value A 3.550” / 90.170mm B 3.775” / 95.885mm C 3.125” / 79.375mm D 0.500” / 12.
Connect Tech Xtreme/SBC PCI-104 Single Board Computer - User Manual Specifications Form Factor PCI-104, (Support up to 4 installed PCI-104 add-on boards) Display VGA, LVDS flat panel Storage 2x SATA (7 pin connector) Serial Interface 2x RS-232, 2x RS-485 USB 4x USB 2.0 Ethernet 1x Gigabit Ethernet Dimensions PC/104 compliant Temperature -20ºC to 70ºC (-4ºF to 158ºF) Power ATX supply input Power Consumption 850 mA @ 5V [1] Qseven carrier circuitry only. Does not include module power.
