USER MANUAL PCIe/104 (PCI/104-Express) to PCI Express Adapter Top Stacking Model CTIM-00054 (0.
PCI-104/Express to PCI Express Adapter User Manual Table of Contents Table of Contents ................................................................................................................................................ 2 Copyright Notice ................................................................................................................................................. 3 Trademark Acknowledgement ......................................................................................
PCI/104-Express to PCI Express Adapter Copyright Notice The information contained in this document is subject to change without notice. Connect Tech Inc. shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved.
PCI/104-Express to PCI Express Adapter Introduction Connect Tech's PCI/104-Express to PCI Express Adapter enables users to install any x1, x4, x8 or x16 lane PCI Express card in a PCI/104-Express stack. This convenient adapter board enables the testing and development for standard PCI Express cards in the PCI/104-Express environment. Features PCI/Express x1, x4, x8, x16 Lane Card Compatible PCI/104-Express & PCIe/104 Compatible SBC Top Stacking Compatible 1.
PCI/104-Express to PCI Express Adapter 2. Hardware Installation PC104 Stand-Offs When installing the ADG017 or ADG20 device into your PCI/104-Express SBC system, four proper stack heights (0.6”) PC/104 standoffs must be used. If standoffs are not used, there is high likelihood that the PCI/104-Express connector can be damaged.
PCI/104-Express to PCI Express Adapter 3. Pinouts and Signal Interconnect Below is a listing of all signal interconnect between the PCI Express connector and the PCI/104-Express connector. Power, ground and presence detection signals have been removed from this list. Any other PCI/104-Express signals not listed, are no connects. PCI Express Connector Pinout Connector Side Pin No.
PCI/104-Express to PCI Express Adapter Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B Side B 5 JTAG2 no connection 6 JTAG3 no connection 7 JTAG4 no connection 8 JTAG5 no connection 11 PERST# 2 PE_RST# 36 OR 48 PEx1_0Clkp OR PEx16_x8_x4_Clkp 13 REFCLK+ 38 OR 50 PE
PCI/104-Express to PCI Express Adapter 4. PCI/104-Express SBC Compatibility Connect Tech's PCI/104-Express to PCI Express Adapter (ADG017 and ADG020) boards enable users to install a x1, x4, x8 or x16 lane PCI Express card in a PCI/104-Express stack. This however can only be done when the adapter is used on the TOP of the stack. Certain CPU boards only populate the PCI/104-Express connector on the bottom side of the board, allowing for a stack down configuration only.
PCI/104-Express to PCI Express Adapter 5. Power Notes Some PCI/104-Express SBC systems will not come with +3.3V power over the PCI/104-Express connector. If this is the case, enable jumper block J1 Position A** (See errata) to enable the on board regulator to generate +3.3V (which is limited to 1.5A) for your PCI Express card. If the SBC you are using does provide +3.3V power, do not enable this jumper.
PCI/104-Express to PCI Express Adapter Limited Lifetime Warranty Connect Tech Inc. provides a Lifetime Warranty for all Connect Tech Inc. products. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non Connect Tech Inc. authorized modification or repair.
