User`s guide

Copyright © 2012 congatec AG TCEDm10 45/94
Table 9 USB Signal Descriptions
Signal Pin # Description I/O PU/PD Comment
USB0+ A46 USB Port 0, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB0- A45 USB Port 0, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB1+ B46 USB Port 1, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB1- B45 USB Port 1, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB2+ A43 USB Port 2, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB2- A42 USB Port 2, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB3+ B43 USB Port 3, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB3- B42 USB Port 3, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB4+ A40 USB Port 4, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB4- A39 USB Port 4, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB5+ B40 USB Port 5, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB5- B39 USB Port 5, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB6+ A37 USB Port 6, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB6- A36 USB Port 6, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB7+ B37 USB Port 7, data + or D+ I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB7- B36 USB Port 7, data - or D- I/O USB 2.0 compliant. Backwards compatible to USB 1.1
USB_0_1_OC# B44 USB over-current sense, USB ports 0 and 1. A pull-up for this line shall
be present on the module. An open drain driver from a USB current
monitor on the carrier board may drive this line low.
I
3.3VSB
PU 10k
3.3VSB
Do not pull this line high on the carrier board.
USB_2_3_OC# A44 USB over-current sense, USB ports 2 and 3. A pull-up for this line shall
be present on the module. An open drain driver from a USB current
monitor on the carrier board may drive this line low. .
I
3.3VSB
PU 10k
3.3VSB
Do not pull this line high on the carrier board.
USB_4_5_OC# B38 USB over-current sense, USB ports 4 and 5. A pull-up for this line shall
be present on the module. An open drain driver from a USB current
monitor on the carrier board may drive this line low.
I
3.3VSB
PU 10k
3.3VSB
Do not pull this line high on the carrier board.
USB_6_7_OC# A38 USB over-current sense, USB ports 6 and 7. A pull-up for this line shall
be present on the module. An open drain driver from a USB current
monitor on the carrier board may drive this line low.
I
3.3VSB
PU 10k
3.3VSB
Do not pull this line high on the carrier board.
Table 10 CRT Signal Descriptions
Signal Pin # Description I/O PU/PD Comment
VGA_RED B89 Red for monitor. Analog DAC output, designed to drive a 37.5-Ohm equivalent load. O Analog PD 150R Analog output
VGA_GRN B91 Green for monitor. Analog DAC output, designed to drive a 37.5-Ohm equivalent load. O Analog PD 150R Analog output
VGA_BLU B92 Blue for monitor. Analog DAC output, designed to drive a 37.5-Ohm equivalent load. O Analog PD 150R Analog output
VGA_HSYNC B93 Horizontal sync output to VGA monitor O 3.3V
VGA_VSYNC B94 Vertical sync output to VGA monitor O 3.3V
VGA_I2C_CK B95 DDC clock line (I²C port dedicated to identify VGA monitor capabilities) I/O OD 5V PU 2k2 3.3V
VGA_I2C_DAT B96 DDC data line. I/O OD 5V PU 2k2 3.3V