System information

ManualsBrandsConel ManualsComputer equipmentUCR11 v2

CONFIGURATION MANUAL

for UCR11 v2 and Bivias v2 routers

Summary of content (105 pages)

PAGE 1
CONFIGURATION MANUAL for UCR11 v2 and Bivias v2 routers
PAGE 2
USED SYMBOLS Used symbols Danger – important notice, which may have an influence on the user’s safety or the function of the device. Attention – notice on possible problems, which can arise in specific cases. Information, notice – information, which contains useful advice or special interest. Firmware version Actual version of firmware is 4.0.0 (11.4.2014). GPL licence Source codes under GPL licence are available free of charge by sending an email to: info@conel.cz. Conel s.r.o.
PAGE 3
CONTENTS Contents 1 Configuration over web browser 1 1.1 Secured access to web configuration . . . . . . . . . . . . 1.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Mobile Connection . . . . . . . . . . . . . . . . . . 1.2.2 Primary LAN . . . . . . . . . . . . . . . . . . . . . 1.2.3 Peripheral Ports . . . . . . . . . . . . . . . . . . . 1.2.4 System Information . . . . . . . . . . . . . . . . . . 1.3 Mobile WAN status . . . . . . . . . . . . . . . . . . . . . . 1.4 WiFi . . . .
PAGE 4
CONTENTS 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.44 1.28.1 Send SMS . . . . . . . . Expansion port configuration . . USB port configuration . . . . . . Startup script . . . . . . . . . . . Up/Down script . . . . . . . . . . Automatic update configuration . User modules . . . . . . . . . . . Change profile . . . . . . . . . . Change password . . . . . . . . Set real time clock . . . . . . . . Set SMS service center address Unlock SIM card . . . . . . . . . Send SMS . .
PAGE 5
LIST OF FIGURES List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Web configuration . . . . . . . . . . . . . . . . . . . Mobile WAN status . . . . . . . . . . . . . . . . . . . WiFi Status . . . . . . . . . . . . . . . . . . . . . . . WiFi Scan . . . . . . . . . . . . . . . . . . . . . . . . Network status . . . . . . . . . . . . . . . . . . . . . DHCP status . . . . . . . . . . . . . . . . . . . . . . IPsec status . . . . . . .
PAGE 6
LIST OF FIGURES 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 GRE tunnel configuration . . . . . . . . . . . . Topology of GRE tunnel configuration . . . . . L2TP tunnel configuration . . . . . . . . . . . . Topology of example L2TP tunnel configuration PPTP tunnel configuration . . . . . . . . . . . . Topology of example PPTP tunnel configuration Example of DynDNS configuration . . . . . . . Example of NTP configuration . . . . . . . . .
PAGE 7
LIST OF TABLES List of Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Mobile connection . . . . . . . . . . . . . . . . . . Peripheral Ports . . . . . . . . . . . . . . . . . . . System Information . . . . . . . . . . . . . . . . . . Mobile Network Information . . . . . . . . . . . . . Description of period . . . . . . . . . . . . . . . . . Mobile Network Statistics . . . . . . . . . . . . . . Traffic statistics . . . . . . . . . . . .
PAGE 8
LIST OF TABLES 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Overview GRE tunnels . . . . . . . . . . . . . GRE tunnel configuration . . . . . . . . . . . Example GRE tunnel configuration . . . . . . L2TP tunnel configuration . . . . . . . . . . . Example L2TP tunel configuration . . . . . . PPTP tunnel configuration . . . . . . . . . . . Example PPTP tunel configuration . . . . . . DynDNS configuration . . . . . . . . . . . . .
PAGE 9
1. CONFIGURATION OVER WEB BROWSER 1. Configuration over web browser Attention! If the SIM card is not inserted in the router, then wireless transmissions will not work. The inserted SIM card must have activated GPRS. Insert the SIM card when the router is switched-off. For monitoring, configuring and managing the router use web interface, which can be invoked by entering the IP address of the router into your browser. The default IP address of the router is 192.168.1.1.
PAGE 10
1. CONFIGURATION OVER WEB BROWSER After green LED starts to blink it is possible to restore initial settings of the router by pressing button RST on front panel. If press button RST, configuration is restored to default and it is reboot (green LED will be on). 1.1 Secured access to web configuration To the web configuration can be accessed via a secure HTTPS protocol. In the event of a default router IP address is a secure router configuration accessed by entering address https://192.168.1.
PAGE 11
1.
PAGE 12
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Profile Current profile – standard or alternative profiles (profiles are used for example to switch between different modes of operation) Supply Voltage Supply voltage of the router Temperature Temperature in the router Time Current date and time Uptime Time indicating how long the router is used Table 3: System Information 1.
PAGE 13
1.
PAGE 14
1. CONFIGURATION OVER WEB BROWSER In the middle part of this page is displayed information about transferred data and number of connections for every SIM card (for each period). The third SIM card is used for CDMA (if router is equipped with a CDMA module) and the remaining SIM cards are standardly designed for LTE/HSPA+ technology (more information about used technologies can be found in the user’s guide).
PAGE 15
1. CONFIGURATION OVER WEB BROWSER 1.4 WiFi This item is available only if the router is equipped with a WiFi module. After selecting the WiFi item in the main menu of the web interface, information about WiFi access point (AP) and associated stations is displayed. Item Description hostapd state dump Time to which statistical data relates num_sta Number of connected stations num_sta_non_erp Number of connected stations using 802.11b in 802.
PAGE 16
1. CONFIGURATION OVER WEB BROWSER 1.5 WiFi Scan This item is available only if the router is equipped with a WiFi module. After selecting the WiFi Scan item in the menu of the web interface, scanning of neighbouring WiFi networks and subsequent printing of results are invoked. Scanning can be performed only if the access point (WiFi AP) is off.
PAGE 17
1.
PAGE 18
1. CONFIGURATION OVER WEB BROWSER 1.6 Network status To view system information about the router operation, select the Network item in the main menu.
PAGE 19
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description collisions Number of collisions on physical layer txqueuelen Length of front network device RX bytes Total number of received bytes TX bytes Total number of transmitted bytes Table 12: Description of information in network status It is possible to read status of connection to mobile network from the network information.
PAGE 20
1. CONFIGURATION OVER WEB BROWSER 1.7 DHCP status Information on the activities of the DHCP server can be accessed by selecting the DHCP status item. DHCP status informs about activities DHCP server. The DHCP server provides automatic configuration of devices connected to the network managed router. DHCP server assigns to each device’s IP address, netmask, default gateway (IP address of router) and DNS server (IP address of router).
PAGE 21
1. CONFIGURATION OVER WEB BROWSER 1.8 IPsec status Information on actual IPsec tunnel state can be called up in option IPsec in the menu. After correct build the IPsec tunnel, status display IPsec SA established (highlighted in red) in IPsec status information. Other information is only internal character. Figure 7: IPsec status 1.9 DynDNS status DynDNS up – dating entry result on server www.dyndns.org can be called up in option DynDNS item in the menu.
PAGE 22
1. CONFIGURATION OVER WEB BROWSER • DynDNS record successfully update. • DNS error encountered. • DynDNS server failure. For correct function DynDNS, SIM card of router must have assigned public IP address. 1.10 System Log In case of any problems with connection to GPRS it is possible to view the system log by pressing the System Log menu item. In the window, are displayed detailed reports from individual applications running in the router.
PAGE 23
1. CONFIGURATION OVER WEB BROWSER Figure 9: System Log Example of logging into the remote daemon at 192.168.2.115: Figure 10: Example program syslogd start with the parameter -r 1.11 LAN configuration To enter the network configuration, select the LAN menu item. ETH network set in Primary LAN configuration, expansion PORT ETH set in Secondary LAN configuration. Item DHCP Client Description • disabled – The router does not allow automatic allocation IP address from a DHCP server in LAN network.
PAGE 24
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description IP address Fixed set IP address of network interface ETH. Subnet Mask IP address of Subnet Mask. Bridged • no – router is not used as a bridge (default) • yes – router is used as a bridge Media type • Auto-negation – The router selects the speed of communication of network options. • 100 Mbps Full Duplex – The router communicates at 100Mbps, in the full duplex mode.
PAGE 25
1. CONFIGURATION OVER WEB BROWSER Item Description Enable dynamic DHCP leases If this option is checked, dynamic DHCP server is enable. IP Pool Start Start IP addresses space to be allocated to the DHCP clients. IP Pool End End IP addresses space to be allocated to the DHCP clients. Lease time Time in seconds, after which the client can use IP address.
PAGE 26
1. CONFIGURATION OVER WEB BROWSER Figure 12: Example LAN configuration 1 Example of the network interface with dynamic and static DHCP server: • The range of allocated addresses from 192.168.1.2 to 192.168.1.4. • The address is allocated 10 minutes. • Client’s with MAC address 01:23:45:67:89:ab has IP address 192.168.1.10. • Client’s with MAC address 01:54:68:18:ba:7e has IP address 192.168.1.11.
PAGE 27
1.
PAGE 28
1. CONFIGURATION OVER WEB BROWSER Example of the network interface with default gateway and DNS server: • Default gateway IP address is 192.168.1.20 • DNS server IP address is 192.168.1.
PAGE 29
1. CONFIGURATION OVER WEB BROWSER 1.12 VRRP configuration To enter the VRRP configuration select the VRRP menu item. VRRP protocol (Virtual Router Redundancy Protocol) is a technique, by which it is possible to forward routing from main router to backup router in the case of the main router failure. If the Enable VRRP is checked, then it is possible to set the following parameters. Item Description Virtual Server IP Address This parameter sets virtual server IP address.
PAGE 30
1. CONFIGURATION OVER WEB BROWSER If Ping Timeout expires with no answer received then process of testing the active line continues the same way like in the case of standard testing process after first test message answer drops out.
PAGE 31
1. CONFIGURATION OVER WEB BROWSER 1.13 Mobile WAN configuration The form for configuration of a connection to the mobile network can be invoked by selecting the Mobile WAN item in the main menu of the router web interface. 1.13.1 Connection to mobile network If the Create connection to mobile network item is selected, the router automatically tries to establish connection after switching-on.
PAGE 32
1. CONFIGURATION OVER WEB BROWSER Tips for working with the Mobile WAN configuration form: • If the size is set incorrectly, data transfer may not be succeeded. By setting a lower MTU it occurs to more frequent fragmentation of data, which means higher overhead and also the possibility of damage of packet during defragmentation. On the contrary, the higher value of MTU can cause that the network does not transfer the packet.
PAGE 33
1. CONFIGURATION OVER WEB BROWSER In the case of the enabled option ping requests are sent on the basis of routing table. Thus, the requests may be sent through any available interface. If you require each ping request to be sent through the network interface, which was created on the occasion of establishing a connection to the mobile operator, it is necessary to set the Check Connection item to enabled + bind. The disabled variant deactivates checking the connection to mobile network.
PAGE 34
1. CONFIGURATION OVER WEB BROWSER 1.13.5 Switch between SIM cards configuration At the bottom of configuration it is possible to set rules for switching between three SIM cards (or between APNs). The third SIM card is used for CDMA (if the router is equipped with WIFI) and the remaining SIM cards are standardly designed for LTE/HSPA+ (more information about used technologies can be found in the user’s guide).
PAGE 35
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Switch to SIM card on the other module when sig. strength drops below "weak" level (and is above "fair" level on target config.) and switch to default SIM card when sig. strength is above "fair" level This parameter enables switching to specified SIM card or APN, when the signal strength drops below specified value (and is above specified value on target configuration).
PAGE 36
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Subsequent Timeout In an unsuccessful attempt to switch to default SIM card, the router on the second attempt to try for the time defined in the parameter Subsequent Timeout, range is from 1 to 10000 min.
PAGE 37
1.
PAGE 38
1. CONFIGURATION OVER WEB BROWSER The figure below describes the situation, when the connection to mobile network is controlled on the address 8.8.8.8 in the time interval of 60 s for primary SIM card and on the address www.google.com in the time interval 80 s for secondary SIM card. In the case of traffic on the router the control pings are not sent, but the traffic is monitored.
PAGE 39
1. CONFIGURATION OVER WEB BROWSER Default SIM card is switched to the offline mode after the router detects roaming. The first attempt to switch back to the default SIM card is executed after 60 minutes, the second after 40 minutes, the third after 50 minutes (40+10) etc.
PAGE 40
1. CONFIGURATION OVER WEB BROWSER 1.14 WiFi configuration This item is available only if the router is equipped with a WiFi module. The form for configuration of WiFi network can be invoked by pressing the WiFi item in the main menu of the router web interface. Enable WiFi check box at the top of this form is used to activate WiFi.
PAGE 41
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description HW Mode HW mode of WiFi standard that will be supported by WiFi access point (AP). • IEE 802.11b • IEE 802.11b+g • IEE 802.11b+g+n Channel Channel where the WiFi AP is transmitting BW 40 MHz Option for HW mode 802.11n that allows using of two standard 20 MHz channels simultaneously. WMM Enables basic QoS for WiFi networks. This version doesn’t guarantee network throughput.
PAGE 42
1.
PAGE 43
1.
PAGE 44
1. CONFIGURATION OVER WEB BROWSER 1.15 WLAN configuration This item is available only if the router is equipped with a WiFi module. The form for configuration of WiFi network and DHCP server functioning on this network can be invoked by pressing the WLAN item in the main menu of the router web interface. Enable WLAN interface check box at the top of this form is used to activate WIFi LAN interface.
PAGE 45
1. CONFIGURATION OVER WEB BROWSER Use Enable dynamic DHCP leases item at the bottom of this form to enable dynamic allocation of IP addresses using DHCP server.
PAGE 46
1. CONFIGURATION OVER WEB BROWSER 1.16 Backup Routes Using the configuration form on the Backup Routes page can be set backing up primary connection by other connections to internet/mobile network. For each back up connection can be defined a priority. Own switching is done based on set priorities and state of the connection (for Primary LAN and Secondary LAN). If Enable backup routes switching option is checked, the default route is selected according to the settings below.
PAGE 47
1. CONFIGURATION OVER WEB BROWSER Figure 26: Backup Routes 1.17 Firewall configuration The first security element which incoming packets must pass is check of enabled source IP addresses and destination ports. It can be specified IP addresses from which you can remotely access the router and the internal network connected behind a router.
PAGE 48
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Target Port The port number on which access to the router is allowed Action Type of action: • allow – access is allowed • deny – access is denied Table 30: Filtering of incoming packets The following part of the configuration form defines the forwarding policy. If Enabled filtering of forwarded packets item is not checked, packets are automatically accepted.
PAGE 49
1. CONFIGURATION OVER WEB BROWSER As a protection against DoS attacks (this means attacks during which the target system is flooded with plenty of meaningless requirements) is used option named Enable protection against DoS attacks which limits the number of connections per second for five.
PAGE 50
1. CONFIGURATION OVER WEB BROWSER Example of the firewall configuration: The router has allowed the following access: • from address 171.92.5.45 using any protocol • from address 10.0.2.123 using TCP protocol on any ports • from address 142.2.26.
PAGE 51
1. CONFIGURATION OVER WEB BROWSER 1.18 NAT configuration To enter the Network Address Translation configuration, select the NAT menu item. NAT (Network address Translation / Port address Translation - PAT) is a method of adjusting the network traffic through the router default transcript and/or destination IP addresses often change the number of TCP/UDP port for walk-through IP packets. The window contains sixteen entries for the definition of NAT rules.
PAGE 52
1. CONFIGURATION OVER WEB BROWSER Enable the following options and enter the port number is allowed remote access to the router from PPP interface. Item Description Enable remote HTTP access on port If this item field and port number is filled in, then configuration of the router over web interface is possible (disabled in default configuration).
PAGE 53
1. CONFIGURATION OVER WEB BROWSER Figure 31: Example NAT configuration 1 In these configurations it is important to have marked choice of Send all remaining incoming packets it default server, IP address in this case is the address of the device behind the router. Connected equipment behind the router must have set Default Gateway on the router. Connected device replies, while PING on IP address of SIM card.
PAGE 54
1.
PAGE 55
1. CONFIGURATION OVER WEB BROWSER In this configuration equipment wired behind the router defines the address Server IP Address. The router replies, while PING on address of SIM card. Access on web interface of the equipment behind the router is possible by the help of Port Forwarding, when behind IP address of SIM is indicating public port of equipment on which we want to come up.
PAGE 56
1.
PAGE 57
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Authenticate Mode Sets authentication mode: • none – no authentication is set • Pre-shared secret – sets the shared key for both sides of the tunnel • Username/password – enables authentication using CA Certificate, Username and Password • X.509 Certificate (multiclient) – enables X.509 authentication in multiclient mode • X.509 Certificate (client) – enables X.509 authentication in client mode • X.
PAGE 58
1. CONFIGURATION OVER WEB BROWSER The changes in settings will apply after pressing the Apply button.
PAGE 59
1. CONFIGURATION OVER WEB BROWSER Example of the OpenVPN tunnel configuration: Figure 36: Topology of example OpenVPN configuration OpenVPN tunnel configuration: Configuration A B Protocol UDP UDP UDP Port 1194 1194 Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.0 Local Interface IP Address 19.16.1.0 19.16.2.0 Remote Interface IP Address 19.16.2.0 19.18.1.
PAGE 60
1. CONFIGURATION OVER WEB BROWSER 1.20 IPSec tunnel configuration IPsec tunnel configuration can be called up by option IPsec item in the menu. IPsec tunnel allows protected (encrypted) connection of two networks LAN to the one which looks like one homogenous. In the IPsec Tunnels Configuration window are four rows, each row for one configured one IPSec tunnel. Item Description Create This item enables the individual tunnels.
PAGE 61
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description IKE Mode Defines mode for establishing connection (main or aggressive). If the aggressive mode is selected, establishing of IPsec tunnel will be faster, but encryption will set permanently on 3DES-MD5. IKE Algorithm Way of algorithm selection: • auto – encryption and hash alg. are selected automatically • manual – encryption and hash alg.
PAGE 62
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Authenticate Mode By this parameter can be set authentication: • Pre-shared key – shared key for both off-side tunnel • X.509 Certificate – allows X.509 certification in multiclient mode Pre-shared Key Sharable key for both parties tunnel. CA Certificate This certificate is necessary to insert Authentication mode x.509. Remote Certificate This certificate is necessary to insert Authentication mode x.509.
PAGE 63
1.
PAGE 64
1. CONFIGURATION OVER WEB BROWSER Example of the IPSec Tunnel configuration: Figure 39: Topology of example IPsec configuration IPsec tunnel configuration: Configuration A B Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.0 Local Subnet 192.168.1.0 192.168.2.0 Local Subnet Mas: 255.255.255.0 255.255.255.
PAGE 65
1. CONFIGURATION OVER WEB BROWSER Item Description Create Enables the individual tunnels Description Displays the name of the tunnel specified in the configuration form Edit Configuration of GRE tunnel Table 41: Overview GRE tunnels Figure 40: GRE tunnels configuration Item Description Description Description of tunnel.
PAGE 66
1. CONFIGURATION OVER WEB BROWSER Figure 41: GRE tunnel configuration Example of the GRE Tunnel configuration: Figure 42: Topology of GRE tunnel configuration GRE tunnel Configuration: Configuration A B Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.
PAGE 67
1. CONFIGURATION OVER WEB BROWSER 1.22 L2TP tunnel configuration L2TP is an unencrypted protocol. To enter the L2TP tunnels configuration, select the L2TP menu item. L2TP tunnel allows protected connection by password of two networks LAN to the one which it looks like one homogenous. The tunnels are active after selecting Create L2TP tunnel.
PAGE 68
1. CONFIGURATION OVER WEB BROWSER Example of the L2TP Tunnel configuration: Figure 44: Topology of example L2TP tunnel configuration Configuration of the L2TP tunnel: Configuration A B Mode L2TP Server L2TP Client Server IP Address — 10.0.0.1 Client Start IP Address 192.168.1.2 — Client End IP Address 192.168.1.254 — Local IP Address 192.168.1.1 — Remote IP Address — — Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.
PAGE 69
1. CONFIGURATION OVER WEB BROWSER 1.23 PPTP tunnel configuration PPTP is an unencrypted protocol. To enter the PPTP tunnels configuration, select the PPTP menu item. PPTP tunnel allows protected connection by password of two networks LAN to the one which it looks like one homogenous. It is a similar method of VPN execution as L2TP. The tunnels are active after selecting Create PPTP tunnel.
PAGE 70
1. CONFIGURATION OVER WEB BROWSER Example of the PPTP Tunnel configuration: Figure 46: Topology of example PPTP tunnel configuration Configuration of the PPTP tunnel: Configuration A B Mode PPTP Server PPTP Client Server IP Address — 10.0.0.1 Local IP Address 192.168.1.1 — Remote IP Address — — Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.
PAGE 71
1. CONFIGURATION OVER WEB BROWSER 1.24 DynDNS client configuration DynDNS client Configuration can be called up by option DynDNS item in the menu. In the window can be defined a third order domain registered on server www.dyndns.org. Item Description Hostname Third order domain registered on server www.dyndns.org Username Username for login to DynDNS server Password Password for login to DynDNS server Server If you want to use another DynDNS service than www.dyndns.
PAGE 72
1. CONFIGURATION OVER WEB BROWSER 1.25 NTP client configuration NTP client Configuration can be called up by option NTP item in the menu. NTP (Network Time Protocol) allows set the exact time to the router from the servers, which provide the exact time on the network. By parameter Enable local NTP service router is set to a mode in which it operates as an NTP server for other devices in the LAN behind the router.
PAGE 73
1. CONFIGURATION OVER WEB BROWSER 1.26 SNMP configuration To enter the SNMP configuration it is possible with SNMP agent v1/v2 or v3 configuration which sends information about the router, eventually about the status of the expansion port CNT or MBUS. SNMP (Simple Network Management Protocol) provides status information about network elements such as routers or end computers.
PAGE 74
1. CONFIGURATION OVER WEB BROWSER Item Description Baudrate Communication speed. Parity Control parity bit: • none – data will be sent without parity • even – data will be sent with even parity • odd – data will be sent with odd parity Stop Bits Number of stop bit. Table 52: SNMP configuration (MBUS extension) Parameters Enable XC-CNT extension and Enable M-BUS extension can not be checked together.
PAGE 75
1. CONFIGURATION OVER WEB BROWSER Continued from previous page OID Description .1.3.6.1.4.1.30140.2.1.6.0 Binary input BIN2 (values 0,1) .1.3.6.1.4.1.30140.2.1.7.0 Binary input BIN3 (values 0,1) .1.3.6.1.4.1.30140.2.1.8.0 Binary input BIN4 (values 0,1) .1.3.6.1.4.1.30140.2.1.9.0 Binary output OUT1 (values 0,1) Table 55: Object identifier for CNT port For the expansion port M-BUS the following range of OID is used: OID Description .1.3.6.1.4.1.30140.2.2.
.1.0 IdNumber – meter number .
PAGE 76
1.
PAGE 77
1. CONFIGURATION OVER WEB BROWSER Figure 50: Example of the MIB browser It is important to set the IP address of the SNMP agent (router) in field Remote SNMP agent. After enter the IP address is in a MIB tree part is possible show object identifier.
PAGE 78
1. CONFIGURATION OVER WEB BROWSER 1.27 SMTP configuration To enter the SMTP it is possible configure SMTP (Simple Mail Transfer Protocol) client, which is set by sending emails. Item Description SMTP Server Address IP or domain address of the mail server. Username Name to email account. Password Password to email account. Own Email Address Address of the sender. Table 57: SMTP client configuration Mobile operator can block other SMTP servers, then you can use only the SMTP server of operator.
PAGE 79
1. CONFIGURATION OVER WEB BROWSER 1.28 SMS configuration SMS Configuration can be called up by option SMS item in the menu. SMS configuration defines the options for sending SMS messages from the router at different defined events and states of the router. In the first part of window it configuration send SMS. Item Description Send SMS on power up Automatic sending of SMS messages after power up. Send SMS on connect to mobile network Automatic sending SMS message after connection to mobile network.
PAGE 80
1. CONFIGURATION OVER WEB BROWSER In the second part of the window it is possible to set function Enable remote control via SMS. After this it is possible to establish and close connection by SMS message. Item Description Phone Number 1 This control can be configured for up to three numbers. If is set Enable remote control via SMS, all incoming SMS are processed and deleted. In the default settings this parameter is turned on. Phone Number 2 This control can be configured for up to three numbers.
PAGE 81
1. CONFIGURATION OVER WEB BROWSER Continued from previous page SMS Description reboot Router reboot get ip Router send answer with IP address SIM card Table 60: Control SMS By choosing Enable AT-SMS protocol on expansion port 1 and Baudrate it is possible to send/receive an SMS on the serial Port 1.
PAGE 82
1.
PAGE 83
1. CONFIGURATION OVER WEB BROWSER After powering up the router, at the mentioned the phone number comes SMS in this form: Router (Unit ID) has been powered up. Signal strength –xx dBm. After connect to mobile network, at the mentioned phone number comes SMS in this form: Router (Unit ID) has established connection to mobile network. IP address xxx.xxx.xxx.xxx After disconnect to mobile network, at the mentioned phone number comes SMS in this form: Router (Unit ID) has lost connection to mobile network.
PAGE 84
1.
PAGE 85
1.
PAGE 86
1.
PAGE 87
1. CONFIGURATION OVER WEB BROWSER 1.29 Expansion port configuration Configuring of the expansion ports PORT1 and PORT2 can cause selecting Expansion Port 1 or Expansion Port 2. Item Description Baudrate Applied communication speed. Data Bits Number of data bits. Parity Control parity bit • none – will be sent without parity • even – will be sent with even parity • odd – will be sent with odd parity Stop Bits Number of stop bit. Split Timeout Time to rupture reports.
PAGE 88
1. CONFIGURATION OVER WEB BROWSER When you select items Use CD as indicator of the TCP connection is activated function indication TCP connection using signal CD (DTR on the router). CD Description Active TCP connection is on Nonactive TCP connection is off Table 67: CD signal description When you select items Use DTR as control of TCP connection is activated function control TCP connection using signal DTR (CD on the router).
PAGE 89
1. CONFIGURATION OVER WEB BROWSER Example of external port configuration: Figure 57: Example of expansion port configuration 1 Figure 58: Example of expansion port configuration 2 Since firmware 3.0.9 all v2 routers provide a program called getty which allows user to connect to the router via the serial line (router must be fitted with an expansion port RS232!).
PAGE 90
1. CONFIGURATION OVER WEB BROWSER 1.30 USB port configuration The USB port configuration can be called up by airbrush option USB Port in menu. Configuration can be done, if we have USB/RS232 converter. Item Description Baudrate Applied communication speed. Data Bits Number of data bits. Parity Control parity bit: • none – will be sent without parity • even – will be sent with even parity • odd – will be sent with odd parity Stop Bits Number of stop bit. Split Timeout Time to rupture reports.
PAGE 91
1. CONFIGURATION OVER WEB BROWSER Item Description Keepalive Time Time, after which it will carry out verification of the connection Keepalive Interval Waiting time on answer Keepalive Probes Number of tests Table 70: USB PORT configuration 2 When you select items Use CD as indicator of the TCP connection is activated function indication TCP connection using signal CD (DTR on the router).
PAGE 92
1.
PAGE 93
1.
PAGE 94
1. CONFIGURATION OVER WEB BROWSER 1.31 Startup script In the window Startup Script it is possible to create own scripts which will be executed after all initial scripts. The changes in settings will apply after pressing the Apply button. Figure 62: Startup script Change take effect after shut down and witch on router by the help of button Reboot in web administration or by SMS message.
PAGE 95
1. CONFIGURATION OVER WEB BROWSER 1.32 Up/Down script In the window Up/Down Script it is possible to create own scripts. In the item Up script is defined scripts, which begins after establishing a PPP/WAN connection. In the item Down Script is defines script, which begins after lost a PPP/WAN connection. The changes in settings will apply after pressing the Apply button.
PAGE 96
1. CONFIGURATION OVER WEB BROWSER 1.33 Automatic update configuration In the window Automatic update it is possible to set automatic configuration update. This choice enables that the router automatically downloads the configuration and the newest firmware from the server itself. The configuration and firmware are stores on the server. To prevent possible manipulation of the update, downloaded file (tar.gz format) is controlled. At first, format of the downloaded file is checked.
PAGE 97
1. CONFIGURATION OVER WEB BROWSER The following examples find if there is a new firmware or configuration each day at 1:00 in the morning. • Firmware: http://router.cz/ucr11-v2.bin • Configuration file: http://router.cz/temelin.cfg Figure 66: Example of automatic update 1 The following examples find if there is a new firmware or configuration each day at 1:00 in the morning. An example is given for the router with the MAC address 00:11:22:33:44:55. • Firmware: http://router.cz/ucr11-v2.
PAGE 98
1. CONFIGURATION OVER WEB BROWSER 1.34 User modules Configuration of user modules can be accessed by selecting the User Modules item. It is possible to add new modules, delete them or switch to their configuration. Use the Browse button to select the user module (compiled module has tgz extension). The module is added using the Add button. Figure 68: User modules Added module appears in the list of modules on the same page. If the module contains index.html or index.
PAGE 99
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Module name Description WMBUS Concentrator Allows to receive messages from WMBUS meters and saves contents of these messages to XML file. pduSMS Sends short messages (SMS) to specified number. GPS Allows v2 router to provide location and time information in all weather, anywhere on or near the Earth, where there is an unobstructed line of sight to four or more GPS satellites.
PAGE 100
1. CONFIGURATION OVER WEB BROWSER 1.36 Change password To open the dialog box for changing the access password select the Change Password menu item. The new password will be saved after pressing the Apply button. In basic settings of the router the password is set on default form root. For higher security of your network we recommend changing this password. Figure 71: Change password 1.
PAGE 101
1. CONFIGURATION OVER WEB BROWSER 1.39 Unlock SIM card Possibility to unlock SIM PIN is under Unlock SIM Card item. If the inserted SIM card is secured by a PIN number, enter the PIN to field SIM PIN and push-button Apply. SIM card is blocked after three failed attempts to enter the PIN code. Figure 74: Unlock SIM card 1.40 Send SMS Sending SMS messages is possible in menu Send SMS. The SMS message will be sent after entering the Phone number and text SMS (Message) and by pushing button Send.
PAGE 102
1. CONFIGURATION OVER WEB BROWSER 1.42 Restore configuration In case it is needed to restore the router configuration, it is possible in Restore Configuration menu item to check configuration by help Browse button. Figure 76: Restore configuration 1.43 Update firmware To view the information about the firmware version and instructions for its update select the Update Firmware menu item. New firmware is selected via Browse button and update the following pressing the Update button.
PAGE 103
1. CONFIGURATION OVER WEB BROWSER 1.44 Reboot To reboot the router select the Reboot menu item and then press the Reboot button.
PAGE 104
2. CONFIGURATION SETTING OVER TELNET 2. Configuration setting over Telnet Attention! If the SIM card isn’t inserted in the router, it is impossible for the router to operate. The Included SIM card must be activated for GPRS transmissions. Monitoring of status, configuration and administration of the router can be performed by means of the Telnet interface. After IP address entry to the Telnet it is possible to configure the router by the help of commands. The default IP address of the modem is 192.168.1.1.
PAGE 105
2.