User manual

Strona 10 z 12 rev. 1.0.2
USER MANUAL: GT06N GPS VEHICLE TRACKER
www.elmic.pl
,
[e-mail]
4. Wire cut-off alarm
When the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS
to the specific numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the
meantime, the device will upload SOS alarm data to the server. And it will send:
Cut Power ！ <Date Time:11-06-17 14 ： 53 ： 06> ， http://maps.google.com/maps?q=N22576713,E113.916585
Note: The specific numbers should be preset, just refer to 6.4
5. Low battery alarm
When the device is only working with battery, once the internal voltage of battery is less than 3.7V, device will send low
battery alarm sms to specific number and alarm on platform.
Low battery alarm sms content example: “Attention!!!battery too low, please charge.” Which means the battery is to low,
to inform user charging it in time.
Note: The specific numbers should be preset, just refer to 6.4
6. Vibration alarm
The vibration alarm function is off by default. To activate this function, please send the following command: SENALM,
ON#. The alarm will be sent to both the service platform and SOS numbers.
When vehicle power is off, ACC status is low, and if the lead time of low ACC is more than 10 minutes （ settable ） , device
will activate security alarm. When the security alarm is on, once the vehicle vibrates for several times, the alarm will be
activated; in the next 3 minutes, if vehicle power is still off （ ACC status is low ） , device will start alarm. At this time, it will
send alarm message to the service platform with the latitude and longitude, while the platform will reply the Chinese
address. Then the terminal will send vibration alarm message to SOS numbers with the Chinese address, and call the SOS
numbers in cycle. If nobody answers, it will stop calling after 3 loops.
If the Chinese address can not be acquired for certain reason, the terminal will send a message with the website link to the
SOS numbers.
e.g.:Sensor Alarm ！ <11-23 14:53>, http://maps.google.com/maps?q=N22576713,E113.916585
Note:
1.The SOS numbers should be preset.
2.Send “SENSOR, OFF#” to turn off the vibration alarm.
7. Voice monitoring
When the special number cell phone dial device, ringing for 10 seconds, it will enter voice monitoring status. At this time,
caller can monitoring the sound in vehicle. Incoming call from non special number will not activate voice monitoring
function.
Note:To realize this function, please set special number beforehand.
The SIM card put into the device should be equipped with caller identification.
8. Oil cut-off
1. Via platform
Send oil cut-off command on platform. To make sure the security of vehicle, tracker can only indicate to cut off oil when
GPS is in valid position status, and the speed is less than 20KM/H or in static. Platform account password is needed when
sending oil cut off command.
2. Via SMS
Firstly, you should set a center number. Please refer to 6.6.Only center number can send the command to the device to
cut off and restore oil.
The format is: RELAY,1#
After the command is carried out, it will reply “Cut off the fuel supply: Success! Speed:0 Km/h”. If the command didn't
carry out, it will reply the reason about fail to carry out.
Note: To ensure the safety of the driver and the car, this command is valid only under two conditions: the GPS is
located; the speed is less than 20km/h
9. Restoring Oil
1. Via platform
When the alarm is off, sending recover oil commands manually. Device will restore oil supplying, and vehicle will work
normally again.
Platform account password is needed when sending oil cut off command.
2. Via SMS
Only center number can send the command to the device to restore oil.
The format is:
RELAY,0#
After the command is carried out, it will receive “Restore fuel supply:Success!”