USER MANUAL NAME: GPS VEHICLE TRACKER GPS + GSM + SMS / GPRS MODEL: GT06N PLEASE READ THE INSTRUCTIONS BEFORE USING THE UNIT. SAVE IT FOR USE IN THE FUTURE. www.elmic.pl, elmic@elmic.pl Importer: Przedsiębiorstwo Handlowo Usługowe FENIKS Cyprian Pawlaczyk ul.
Safety Warning & Attentions .................................................................................................................................................... 3 1. Attention ...................................................................................................................................................................... 3 2. Attention for operation of this product ............................................................................................................
Introduction Thank you for choosing this GPS Vehicle Tracker. Please read this Manual carefully to fully understand its usage, perfect functions and simple operation. This product not only provides tracking function but also provides cutting petrol or electricity of your car to meet your requirements of monitoring comprehensively car security. The Company reserves the right to modify this Manual from time to time without prior notice.
2. Appearance: 3. Usage: • • • • • • for cars for vans for trucks for camper for buses for other vehicles 4. Performance parameters: Serial 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Strona 4 z 12 Specifications Dimension Weight Backup Battery Operation Temperature Humidity Standby Time GSM Frequencies GPRS GPS Channel GPS Sensitivity Acquisition Sensitivity Position Accuracy Technical parameters 106(L) x 54(W) x 16(H) mm 96g 450mAh / 3.
. LED Indicators Status: GPS LED Indicator – Blue Status Implication Flashing (interval 0.1s) Searching GPS signal Solid blue GPS fix OFF No GPS fix or initializing Status Implication Quick flashing (interval 0.1s) GSM initializing Slow flashing (flash 0.1s every 2s) Receive GSM signal normalny Solid green Connected to GSM Network OFF No GSM Signac Status Implication Flashing (interval 0.1s) Low battery Slow flashing (interval 0.2s) Full charge Slow flashing (flash 0.
3. Wiring configuration Notes of the relay wiring The relay wiring of pump: oil connectors of both ends are a fine white line (85) and a fine yellow line (86). The fine white line (85) is connected to vehicle positive power (+12V). The fine yellow line is connected to the device relay control line. Cut off the positive connection line of the pump; then connect in series to the relay N.C. contact (thick green line 87a) and the other end to relay COM contact (thick green line 30). Line No. 1. 2 3.
5. Power/ACC/Tele-cutoff(petrol/electricity) control line (4 pin) 1. Your device comes with a power cord and is designed to use only manufacturer-specified original device. The red line is positive while the black one is negative (the side should not be connect with ground wire). 2. The ACC line (white) connects to ACC switch of the vehicle. Please be sure to connect the ACC line; otherwise the device will enter ignition detection status when disconnect the ACC line.
5. Delete specific number Before deleting specific number, please check its corresponding code. For the code, please SMS “PARAM#” to the device. SMS command to the device to delete the number. SOS,D,serial NO.1,serial NO.2,serial NO.3# “D” means to delete the number, for example: SOS,D,1# means to delete the first number SOS,D,3# means to delete the third number If you want to delete more than one numbers, you can send this command: SOS,D,1,3# means to delete the first and third numbers.
10. GPRS time interval The default GPRS time sending interval is 10s which means the device will upload positioning data to the platform server every 10s. Users can modify GPRS time sending interval by SMS “TIMER,time(second)#”. The time ranges from 10-18000s For example: TIMER,10# It means the device will upload data to the server every 10s. 11. Sensor alarm time setting When the vehicle power is off and ACC is in low-level, if ACC is off over 10 minutes, the device will enter sensor alarm state.
4. Wire cut-off alarm When the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS to the specific numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the device will upload SOS alarm data to the server. And it will send: Cut Power！， http://maps.google.com/maps?q=N22576713,E113.916585 Note: The specific numbers should be preset, just refer to 6.
10. Over speed Alarm When the car is moving over a limited speed in average in a limited time period, then the device will send over speed alarm SMS to user.
Producer: Shenzhen Concox Information Technology Co., Ltd. China www.concox.cn Strona 12 z 12 Importer: Przedsiębiorstwo Handlowo Usługowe FENIKS ul. Słoneczna 110, Nowa Kuźnica, 42-350 Koziegłowy Poland www.elmic.pl, elmic@elmic.pl rev. 1.0.2 USER MANUAL: www.elmic.pl, elmic@elmic.
