GPS Vehicle tracker (Anti-theft Tracking & Positioning) USER MANUAL (Version 2.3) Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only.
1. Accessories: 2. Features: Wide voltage input range: 9-36v DC GPS position upload via GPRS as preset interval Check location via SMS Built-in vibration sensor, intelligent theft proof ACC ignition detection Tele-cutoff (petrol/ electricity) function 3.
.1 Red LED (Power/Working Status) LED Status Continuously in dark state Flash slowly Indication Power off Working normally 3.2 Green LED (GSM Status Indicator) LED Status Flash Flash slowly Continuously in dark state Indication Receive GSM signal normally Start GPRS No GSM signal 3.3Blue LED (GPS Status Indicator) LED Status Flash quickly Flash slowly Continuously in dark state 3.4 Defense Status Indication Three LEDs (blue/red/green) flash cyclically. 4. Method of Installation 4.
Note: Power off before installing or removing the SIM card. The SIM card used should be available for GPRS 4.2 Installation Notes Concealed installation, be aware of water drops Stay away from interference of electromagnetic signals Fixed firmly into position Make sure the device face towards sky, with no metal object above it to interfere with GPS signal The standard voltage is 9V-36VDC. Please use the power line which provided by the manufacturer.
The device will power on automatically when connected to power. The power LED will light up. 5. Cautions 5.1 Power: The standard power supply voltage is 9V-36VDC. Please use the power line which provided by the manufacturer. The red line is for the positive and the black line is for the negative. 5.2 ACC/Tele-cutoff (petrol/electricity) Control Line 5.2.1 ACC line (white) should be connected to the ACC switch of the vehicle.
and it will keep activating vibration alarms while the vehicle is moving. To disable vibration alarm and theft proof function, please connect the ACC line directly to the positive power supply and maintain a high level. 5.2.2 Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket). 5.3 Relay The standard accessory of relay is 12v which is only for vehicles with 12v battery.
SOS,A,,13510905992# means to set the second number SOS,A,,,13510905993# means to set the third number If the setting is successful, the terminal will reply“OK”. 6.3 Delete SOS Numbers To delete a specific SOS number, you can send query command to check its corresponding serial number and then send command to delete it. Any mobile could send the following command to delete a specific SOS number; SOS,D,serial NO.1,serial NO.2,serial NO.
6.5 Set the interval of GPRS data-transmission The default interval is 20s which means device will send GPS positioning data to server every 20s. The command to set the interval is as follows; TIMER,time(seconds)# The range is from 10-18000s. e.g. TIMER,10# 6.6 Defense-activation timer setting ACC line keeps low for 10 minutes; the terminal will enter defense state. Several vibrations happen after that, the vibration alarm system will be activated.
7. Operations 7.1 Check Location 7.1.1 Query Coordinates by SMS To query coordinates of the terminal, you can send the query command to it. The terminal will reply the coordinates of last location. If it fails to get location information, it will reply the message as follows: “No data!” Command format: WHERE# Example: Lat:N22.571285,Lon:E113.877115,Course:42.20,Speed:0.0740,DateTime:10-11-23 22:28:51 7.1.
2. Send SENSOR,0# to the terminal, you can turn off the vibration alarm. 3. Send ALM,OFF# to disable SMS alarm function. Send ALM,ON# to activate SMS alarm function. 7.3 Cut-off Petrol/Electricity In case the vehicle is stolen, the users can send command from the platform to cut off the Petrol/Electricity to stop the vehicle from moving. Platform account and password must be entered for Petrol/Electricity cut-off, the messages replied by terminal can be checked in the log.
③ Check whether SIM card balance is enough ④ Check SIM card GPRS service; ⑤ Check the parameter settings, to ensure whether IMEI number and GPRS transmission interval are right. 9.3 If the device can not get GPS signal for a long time, please check its location of installation: ① Please make sure the GPS antenna face up; ② Please make sure there is no metal above the device, and the windshield above it is without thermal-protective coating, which will affect the GPS reception. 9.
