Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 1 Table of Contents Important Information............................................................................................2 Precautions ............................................................................................................3 1. Product Overview ............................................................................................4 Getting started ....................................................................
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 2 IMPORTANT INFORMATION FCC Statement This device complies with part 15 the FCC Rules. Operation is subject to the following two conditions: (i) This device may not cause harmful interference, and (ii) this device must accept any interference received, including interference that may cause undesired operation.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 3 PRECAUTIONS Test Shots Always take a test photograph to check that the camera is functioning normally. The liability for any incidental losses (such as the cost of photography or the loss of income from photography ) incurred as a result of fault with this product cannot be accepted.
Easy Too Inst.Manual(5S1048-00) 19/6/02 5:41 pm Page 4 1. Product overview FRONT 1 2 1. Shutter Button 2. Viewfinder 3. Strap eyelet 4. Lens 3 4 BACK 5 5. LCD display 6. Feature button 7.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 5 Getting started Congratulations on your purchase of the Concord Eye-Q Easy Too digital camera. This camera features 8 MB of internal SD RAM memory allowing you to store still images or short video clips in the camera. Please read this manual before operating the camera to become more familiar with the features of this versatile digital camera.
Easy Too Inst.Manual(5S1048-00) 21/6/02 9:54 am Page 6 Important battery information The Eye-Q Easy Too camera uses a type of memory that continually draws power to retain the pictures in the camera’s internal memory even if the camera is powered off. If the battery power is depleted and you have not transferred your images to the computer, you will lose them. It is strongly recommended that you transfer your images to the computer promptly and then remove the batteries to extend their life.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 7 Turning the camera on and off and learning the LCD display Turn the camera on by pressing the Feature Button once. Two beeping sounds will be heard. Press the Feature Button to cycle through the Feature Modes. To exit the Feature Mode, continue to press the Feature button until the LCD displays a number or wait 5 seconds without pressing any buttons.
Easy Too Inst.Manual(5S1048-00) 21/6/02 9:54 am Page 8 Selecting the power supply To extend the battery life, remove the batteries from the camera when it is not in use. Remember to transfer your pictures to your computer first or you will lose them. Note: • Do not use different types of batteries together. • Soiling, such as fingerprints on the battery terminals, can significantly reduce the battery life. • Do not use new and used batteries together.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 9 2. Taking Pictures Press the shutter button once to take a picture. A high-pitched beeping sound will indicate that the picture was taken and the counter displayed on the LCD will decrease showing the number of images left. Note: A lowpitched beeping sound indicates that the image has not been taken. This is probably due to low light intensity. Please adjust the lighting and retake the image.
Easy Too Inst.Manual(5S1048-00) 21/6/02 9:55 am Page 10 Changing the resolution To change the resolution, press the Feature Button until the resolution option is displayed in the LCD. The resolution is noted by HI for high resolution and Lo for Low resolution. When the resolution you are currently in appears in the LCD, press the shutter button to change to the other resolution option.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 11 Self-Timer Press the Feature Button until ‘St’ appears in the LCD. Press the Shutter button to start a 10-second self-timer count down. The camera will issue a series of short beeps followed by a long beep. When the image has been captured, the camera will beep again.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 12 Changing the Lighting Hz Different countries use different lighting frequencies. The US uses a 60Hz frequency while Europe uses a 50Hz frequency. The Easy Too camera gives you the option to switch the Hz frequency as you travel. To change the frequency, press the Feature Button until the frequency option denoted by either 50 or 60 is displayed in the LCD.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Delete Funtion Press the Feature Button until either CA or CL appears in the LCD. • CA stands for clear all and is used to delete all images. • CL stands for clear last and is used to delete the last image. To delete the last image taken, press the shutter button once after CL appears in the LCD. To delete All Images, press the Feature Button until CA appears in the LCD.
Easy Too Inst.Manual(5S1048-00) 28/6/02 5:39 pm 3. Installing the Camera driver Installing the software on a Windows PC The following software will be installed in the installation sequence: • Arcsoft PhotoImpression 3 1. Concord EyeQ Easy too setup is preparing the installshield wizard which guide you though the rest of the setup process, click "cancel" if you want to quit. 2. After the preparation completed, you can click " next" to start the software installation.
Easy Too Inst.Manual(5S1048-00) 28/6/02 5:39 pm Page 15 7. Setup will add program icon to the program folder list. You may type a new folder name, or select one from the existing folder. Press "next" to continue to next process. 8. PhotoImpression setup is performing the request operation. Finally, press "Finish" to complete the installation.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 16 Connecting the camera to your PC When you finish taking pictures, you can connect your camera to your PC and upload your images through the USB cable supplied. Plug one end of the USB cable into your camera and the other end into the USB port of your PC (located either at the back your PC or in the front panel). When the camera is connected, you will hear a beeping sound from the camera indicating that the PC is supplying power to the camera.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 17 Uploading your video clips to your PC 1. Open "My DSC" application program in windows start program menu. 2. Press the "download file" button. 3. Select download all pictures or some pictures. 4. Highlight the "AVI" clip you want. 5. Press "save photo" button. 6. Set the frame rate. 7. Create the file name. 8. Press the"Save" button. Note: Fame rate means how many pictures will be shown per second. It will affect the movie clip length.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 18 Uninstalling the software on a Windows PC The User can automatically uninstall the software using the "Add/Remove Program" in the Control Panel. Note: Use this procedure only when the installed software is no longer required or when the software installation fails. Procedure: 1. Switch on your PC and start up Windows. 2. Open the "My Computer" windows and double-click on "Add/Remove Programs" in the Control Panel. 3.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 19 Uninstalling the driver on a Windows PC User can automatically uninstall the driver using "Device Manager" in the Control Panel. Note: Use this procedure only when the digital camera is no longer required or when the driver installation fails. Procedure: 1. Connect the digital camera to your PC. 2. Switch on your PC and start up Windows. 3. Open the "My Computer" windows and double-click "System" in the Control Panel. 4.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 20 4. Cleaning and maintenance Be sure to read this information to ensure that you use your camera correctly. Places to Avoid Do not store or use the camera in the following places or locations: • Very humid, dirty or dusty places. • In direct sunlight or in places subject to extreme increases in temperature such as in a closed car during summer. • Extremely cold places. • Places subject to strong vibrations. • Places affected by smoke or steam.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 21 Storing the camera If you do not intend to use the camera for a long period of time, remove the batteries before storing the camera. Cleaning your Camera Use a blower brush to remove dust from the lens and LCD surface and then wipe lightly with a soft, dry cloth. If any soiling remains, apply a small amount of lens cleaning liquid to a piece of lens cleaning paper and wipe gently.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 22 5. Troubleshooting The troubleshooting guide is designed to help you. If problems continue, please contact your local customer support hot-line. For Windows® User: SYMPTOM PROBLEM SOLUTION You have lost power to your CONCORD EYE-Q EASY Too All the images I have taken do not by either: appear. Insufficient battery power. Upload all images to your PC as soon as possible. Refer to Battery Guidance section in the User’s Manual.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 23 SYMPTOM PROBLEM SOLUTION My CD installation wizard does not work. The auto installation file is switched to off or the CD ROM is not in the drive. Go to the computer desktop. Right click on “My Computer.” Click on “Properties.” Select “Device Manager” and double click on “CD-Rom.” Double click on “CD-R.” Click on “Setting.” Ensure “Auto insert notification” is checked and the “disconnect” is selected.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 24 6. Getting Help If you need help with your camera, refer to the Troubleshooting section of this manual. If you still cannot find the solution, visit our Web site at www.support.concordcam.com. Most support issues are answered in the Frequently Asked Questions (FAQ) section.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 25 7.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 26 Camera Specifications LCD display Show image counter Off mode Self timer mode Video mode Delete all mode Delete last mode Change resolution (Hr/Lr) Select frequency (50Hz / 60Hz) High density mode (Hd/Ld) Beeper Yes Auto power-off Stand by mode (After 20 seconds inactivity) Low battery warning /indicator LCD display will flash Power supply 2 x AAA alkaline battery Back up power No Dimension 79.12mm (L) x 59.8mm (H) x 26.
Easy Too Inst.Manual(5S1048-00) 19/6/02 9:49 am Page 27 8. Warranty Information LIMITED WARRANTY The manufacturer warrants your Concord Eye-Q Easy Too camera for a period of 1 year from the date of purchase to be free from defects in material and workmanship. The warranty period shall be extended accordingly if applicable mandatory legislation in effect on the date of purchase requires a longer warranty period.
Technical Support Hot Line: Toll Free In the USA & Canada 1-866-522-6372 Toll Free In Europe UK: 0800-169-6482 BELGIUM: 0800-787-57 FRANCE: 0800-917-599 GERMANY: 0800-1800-563 SPAIN: 900-973-195 ITALY: 800-781-883 All Other Countries - Toll 31-53-482-9779
