SAFETY DATA SHEET P008 Section 1. Identification Product name : STEP ONE® Quick Dry Alkyd Stainblocking Primer/Sealer Product code : P008 Other means of identification : Not available. Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Not applicable. Manufacturer : Conco Paints 101 Prospect Avenue N.W. Cleveland, OH 44115 Emergency telephone number of the company : (216) 566-2917 Product Information Telephone Number : Not available.
Section 2. Hazards identification General Prevention Response Storage : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. : Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves. Wear eye or face protection. Wear protective clothing. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Section 4. First aid measures Description of necessary first aid measures Eye contact Inhalation Skin contact Ingestion : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Section 4. First aid measures Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. See toxicological information (Section 11) Section 5.
Section 6. Accidental release measures Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g.
Section 8. Exposure controls/personal protection Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.
Section 9. Physical and chemical properties Relative density : 1.61 Solubility : Not available. Partition coefficient: noctanol/water : Not available. Auto-ignition temperature : Not available. Decomposition temperature : Not available. Viscosity : Kinematic (room temperature): <0.205 cm2/s (<20.5 cSt) Kinematic (40°C (104°F)): <0.205 cm2/s (<20.5 cSt) : Not applicable. Molecular weight Aerosol product Heat of combustion : 9.631 kJ/g Section 10.
Section 11. Toxicological information Classification Product/ingredient name OSHA IARC NTP Titanium Dioxide - 2B - Reproductive toxicity Not available. Teratogenicity Not available. Specific target organ toxicity (single exposure) Name Category Route of exposure Target organs Isoparaffinic HC Solvent Category 3 Not applicable. Lt. Aliphatic Hydrocarbon Solvent Category 3 Not applicable.
Ingestion : Adverse symptoms may include the following: nausea or vomiting Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure Potential immediate : Not available. effects Potential delayed effects : Not available. Long term exposure Potential immediate effects : Not available. Potential delayed effects : Not available. Potential chronic health effects Not available. General : May cause damage to organs through prolonged or repeated exposure.
Section 12. Ecological information Other adverse effects : No known significant effects or critical hazards. Section 13. Disposal considerations Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements.
Section 14. Transport information Special precautions for user : Multi-modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (sea, air, etc.), does not indicate that the product is packaged suitably for that mode of transport.
Section 16.