SAFETY DATA SHEET 8500(79) Section 1. Identification Product name Product code : Interior/Exterior Alkyd Gloss Industrial Strength Enamel Black : 8500(79) Other means of : Not available. identification CAS # : Not applicable. Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Not applicable. Manufacturer : Conco Paints 101 Prospect Avenue N.W.
Section 2. Hazards identification Hazard statements : Flammable liquid and vapor. May cause an allergic skin reaction. May cause cancer. Suspected of damaging fertility or the unborn child. May be fatal if swallowed and enters airways. May cause respiratory irritation. May cause drowsiness or dizziness. Causes damage to organs through prolonged or repeated exposure.
Section 3. Composition/information on ingredients Ingredient name % by weight CAS number Med. Aliphatic Hydrocarbon Solvent Mineral Spirits 140-Flash 2-Butoxyethanol Xylene Carbon Black Calcium 2-Ethylhexanoate Zirconium 2-Ethylhexanoate 2-(2-Methoxyethoxy)-ethanol Methyl Ethyl Ketoxime Ethylbenzene Cobalt 2-Ethylhexanoate Crystalline Silica, respirable powder 15.09 5.78 3.74 1.8 1.6 1.15 0.36 0.35 0.32 0.32 0.19 0.
Section 4. First aid measures Ingestion : Can cause central nervous system (CNS) depression. May be fatal if swallowed and enters airways. Over-exposure signs/symptoms Eye contact : No specific data.
Section 5. Fire-fighting measures Special protective actions for fire-fighters Special protective equipment for fire-fighters : Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool.
Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities : Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.
Section 8. Exposure controls/personal protection STEL: 10 mg/m³, (as Zr) 15 minutes. OSHA PEL (United States, 6/2016). TWA: 5 mg/m³, (as Zr) 8 hours. None. AIHA WEEL (United States, 10/2011). Skin sensitizer. TWA: 10 ppm 8 hours. ACGIH TLV (United States, 3/2016). TWA: 20 ppm 8 hours. NIOSH REL (United States, 10/2013). TWA: 100 ppm 10 hours. TWA: 435 mg/m³ 10 hours. STEL: 125 ppm 15 minutes. STEL: 545 mg/m³ 15 minutes. OSHA PEL (United States, 6/2016). TWA: 100 ppm 8 hours. TWA: 435 mg/m³ 8 hours.
Section 8. Exposure controls/personal protection TWA: 10 ppm 8 hours. CA Ontario Provincial (Canada, 7/2015). TWA: 0.02 mg/m³, (as Co) 8 hours. Form: Inorganic CA British Columbia Provincial (Canada, 5/2015). TWA: 0.02 mg/m³, (as Co) 8 hours. CA Quebec Provincial (Canada, 1/2014). Skin sensitizer. TWAEV: 0.02 mg/m³, (as Co) 8 hours. CA Saskatchewan Provincial (Canada, 7/2013). STEL: 0.06 mg/m³, (measured as Co) 15 minutes. TWA: 0.02 mg/m³, (measured as Co) 8 hours.
Section 8. Exposure controls/personal protection Hand protection Body protection Other skin protection Respiratory protection : Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties.
Section 10. Stability and reactivity Reactivity : No specific test data related to reactivity available for this product or its ingredients. Chemical stability : The product is stable. Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition.
Section 11. Toxicological information Methyl Ethyl Ketoxime Eyes - Severe irritant Rabbit - Ethylbenzene Eyes - Severe irritant Rabbit - Skin - Mild irritant Rabbit - 100 microliters 500 milligrams 24 hours 15 milligrams - Sensitization Not available. Mutagenicity Not available. Carcinogenicity Not available.
Section 11. Toxicological information Name Category Route of exposure Target organs Med.
Potential immediate effects : Not available. Potential delayed effects : Not available. Long term exposure Potential immediate effects : Not available. Potential delayed effects : Not available. Potential chronic health effects Not available. General Carcinogenicity : Causes damage to organs through prolonged or repeated exposure. Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels. : May cause cancer.
Section 12. Ecological information Bioaccumulative potential Product/ingredient name LogPow BCF Potential Xylene Calcium 2-Ethylhexanoate Zirconium 2-Ethylhexanoate Methyl Ethyl Ketoxime Cobalt 2-Ethylhexanoate - 8.1 to 25.9 2.96 2.96 2.5 to 5.8 15600 low low low low high Mobility in soil Soil/water partition coefficient (KOC) : Not available. Other adverse effects : No known significant effects or critical hazards. Section 13.
Section 14. Transport information Additional information This product may be re-classified as "Combustible Liquid," unless transported by vessel or aircraft. Non-bulk packages (less than or equal to 119 gal) of combustible liquids are not regulated as hazardous materials in package sizes less than the product reportable quantity. ERG No. Product classified as per the following sections of the Transportation of Dangerous Goods Regulations: 2. 18-2.19 (Class 3). - ERG No. ERG No.
Section 16. Other information Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks Although HMIS® ratings are not required on SDSs under 29 CFR 1910. 1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may be purchased exclusively from J. J.
Date of issue/Date of revision : 4/17/2017 Date of previous issue : 1/16/2017 Version : 5.
