Technical Specifications

SURFACE PREPARATION
WARNING! Removal of old paint by sanding, scraping or other means
may generate dust or fumes that contain lead. Exposure to lead dust
or fumes may cause brain damage or other adverse health effects,
especially in children or pregnant women. Controlling exposure to
lead or other hazardous substances requires the use of proper
protective equipment, such as a properly fitted respirator (NIOSH
approved) and proper containment and cleanup. For more
information, call the National Lead Information Center at 1-800-424-
LEAD (in US) or contact your local health authority.
Preparation
To ensure proper adhesion, all surfaces must be clean, dry, and free
from dirt, wax, grease, oil, chalk, mildew and loose or peeling paint.
Nail holes, cracks and other surface imperfections should be properly
filled, sanded smooth and dusted clean. All mildew and mold must be
completely and thoroughly removed. Glossy surfaces must be sanded
and dusted clean. Always wear a properly selected and fitted
NIOSH/MSHA approved dust mask or respirator when sanding.
Ferrous Metal
Remove all rust by hand tool cleaning per SSPC-SP2 and remove oil
and grease by solvent cleaning per SSPC-SP1. For best performance
use commercial blast cleaning per SSPC-SP6 with a sharp, angular
abrasive. Prime bare steel within 8 hours or before flash rusting
occurs.
Galvanized Metal
Allow to weather for 6 months and solvent clean per SSPC-SP1. If
weathering is not possible or surface has been treated with chromates
or silicates, solvent clean per SSPC-SP1 and apply a test area. Test
adhesion after one-week dry time. If adhesion is poor, brush blast per
SSPC-SP7. At minimum, rusty galvanizing should be hand tool cleaned
per SSPC-SP2, followed by same day painting. No primer necessary.
Aluminum
Remove all corrosion by hand tool cleaning per SSPC-SP2 and remove
oil and grease by solvent cleaning per SSPC-SP1. No primer necessary.
Wood
Sand weathered areas to fresh wood. Scrape, sand and spot prime
knots and pitch steaks. Fill nail holes. Prime with Conco P007
Interior/Exterior All Surface Acrylic Stainblocking Primer.
Masonry, Plaster, Aggregate
Block (allow to cure for 30 days)
Remove all surface contamination by washing with an appropriate
cleaner. Allow concrete, mortar and plaster to cure for 30 days at
75°F. Brick must weather one year. Remove any loose mortar, dust
and contamination per SSPC-SP13. Remove form release compounds
and curing membranes by brush blasting. No primer necessary. Bare
block should be filled with Conco P9511 Interior/Exterior
Drywall
Fill cracks and holes with spackling compound and sand smooth. Joint
compound must be cured and sanded smooth. Remove all sanding
dust. Prime before top coating.
Mildew
Remove before painting by washing with a solution of 1 part liquid
bleach and 3 parts water. Apply the solution and scrub the mildewed
area. Allow the solution to remain on the surface for 10 minutes.
Rinse thoroughly with water and allow the surface to dry before
painting. Wear protective eyewear, waterproof gloves and protective
clothing. Quickly wash off any of the mixture that comes in contact
with your skin. DO NOT ADD DETERGENTS OR AMMONIA TO THE
BLEACH/WATE R SOLUTION.
CLEAN UP/DISPOSAL
• Clean hands and tools with warm, soapy water
• Promptly wipe up spills and spatters with a damp cloth
• In event of a spill, use sand or kitty litter to absorb the spille
d
product
• Dispose of empty container or unused portion in accordance
w
ith local, state, and federal regulations
• After cleaning, flush spray equipment with mineral spirits t
o
prevent rusting of the equipment
• Follow manufacturer’s safety recommendations when usi
ng
mineral spirits
CAUTIONS
• Not for use on horizontal surfaces where water may collect
• Do not apply in direct sunlight
• Keep from freezing
• Do not use hydrocarbon solvents for cleaning prior to painting
WARRANTY
If this product, when applied according to label instructions, fails
to perform to your complete satisfaction, we will either replace
an equivalent quantity of product free of charge or refund the
purchase price, upon presentation of proof of purchase. This
warranty does not include labor or costs associated with labor for
the application of any product. This warranty gives you specific
legal rights, and you may have other rights, which vary state to
state.
The information and recommendations set forth in this Product Data Sheet are
based upon tests conducted by or on behalf of Conco Paints. Information and
recommendations set forth herein are subject to change and pertain to the product
offered at the time of publication. Consult your Conco Paint retailer or sales
representative to obtain the most recent Product Data Sheet.
For more information, please call 1.800.388.2426, or www.concopaints.com