Technical Specifications

Conco® 8000 Series Interior/Exterior Acrylic High Gloss is an industrial strength coating designed for new construction and
maintenance applications. Conco 8000 Series features a tough direct-to-metal, abrasion resistant formula, as well as maximum
gloss and color retention, and resistance to corrosion, chemicals and flash rust. Confidently coat and protect machinery,
equipment, piping, doors and trim with this high performance coating.
8000 SERIES
INDUSTRIAL STRENGTH COATING
INTERIOR/EXTERIOR HIGH GLOSS
BRIGHT WHITE/PASTEL BASE, ACCENT BASE, SAFETY RED, SAFETY YELLOW, ALUMINUM, BLACK
FEATURES
• Industrial strength coating designed for new construction and
maintenance applications
• Ideal for painting over prepared metal, wood, masonry,
int
erior plaster and drywall
• Provides excellent abrasion, corrosion and c
hemical resistance
while offering exceptional gloss and color retention
• Direct to metal application while protecting against flash rust
• Outstanding adhesi
on
• Ba
cked by a 100% Satisfaction Assured Warranty
• Master Painters Institute #154
TECHNICAL DATA*
Vehicle: Acrylic
Finish: 70-100 units @ 60°
Flash Point: N/A
Weight Solids: 43% ± 2%
Volume Solids: 35% ± 2%
Dry Time (@ 77°F and 50% R.H.)
To Touch: 1 Hour
To Recoat: 4 Hours
Cures: 30 Days
Weight Per Gallon: 9.5 lb/gal
VOC: <50 g/L – 0.42 lb/gal
as per 40 CFR 59.406
Spread Rate: 155-250 sq.ft. per gallon
(dependent on surface texture and porosity)
Film Thickness: @ 8 mils wet; 2.8 mils dry
Sizes: Gallons, Five Gallons
*Technical Data based on Bright White/Pastel Base
APPLICATION
Do not apply when air, surface or product temperature is below
50°F or above 110°F, when relative humidity exceeds 85%, or
when rain is forecasted within 16-24 hours of painting.
Temperature must be at least 5°F above dew point.
Spray – Airless
Pressure 1500 psi
Tip .017” - .021”
Reduce with water for spray only, up to 12%
Brush
Use a quality nylon/polyester brush.
Roller
Use a 3/8” nap synthetic roller cover.
RECOMMENDED SYSTEMS
Ferrous Metal
1 coat Conco P851 DTM Alkyd Rust Control Metal Primer or
1 coat Conco P801 DTM Acrylic Prime & Finish
1 or
2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
Aluminum & Galvanized Metal
1 or 2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
Masonry & Plaster (allow to cure for 30 days)
1 or 2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
Aggregate Block
1
coat Conco P9511 Interior/Exterior Acrylic Latex Block Filler
1 or 2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
Interior Drywall
1 coat Conco P001 Interior Drywall PVA Primer/Sealer
1 or 2 coa
ts Conco 8000 series DTM Acrylic Gloss Industrial Enamel
Wood
1 Conco P007 Interior/E
xterior All Surface 100% Acrylic Stain blocking Primer
1 or 2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
TIPS FOR BETTER PERFORMANCE
• On rusty surfaces, apply first coat by brush
• Use 50% overlap when spraying
• When used a primer/finish apply two coats
• Stir w
ell before using
• I
f using more than one package of the same color, mix together
bef
ore applying to ensure uniform color
• Clean the surface thoroughly
• Sand surface smooth to ensure an even surface
• Prepare the substrate to create a uniform surface
• Patch cracks, crevices and trough-w
a
ll openings using a proper
sealant or patch
• Caulk as needed using a quality latex or siliconized latex caulk
or
sealant