Technical Specifications

Application
Do not apply at air, surface or product
temperatures below 50°F or when air or surface
temperatures may drop below 50°F within 24
hours.
Spray – Airless
Pressure………………………….2000 psi
Tip……………………………0.015”-0.019”
May be thinned with up to 1 pint of water per
gallon of paint for spray application.
Brush
Use a quality nylon/polyester brush.
Roller
Use a 3/8” nap synthetic roller cover.
Tips for Better Performance
 Stir well before using
 If using more than one package of the same
color, mix together before applying to ensure
uniform color
 Clean the surface thoroughly
 Sand surface smooth to ensure an even
surface
 Prepare the substrate to create a uniform
surface
 Patch cracks, crevices and through-wall
openings using proper sealant or patch
 Fill voids and openings around windows and
doors using proper sealant or patch
 Caulk as needed using quality latex or
siliconized latex caulk or sealant
Cautions
 For interior use only
 Keep from freezing
 Not for use on roofs, floors or decks
 Not for use on horizontal surfaces where
water may collect
Surface Preparation
WARNING! Removal of old paint by sanding, scraping or other means may
generate dust or fumes that contain lead. Exposure to lead dust or fumes
may cause brain damage or other adverse health effects, especially in
children or pregnant women. Controlling exposure to lead or other
hazardous substances requires the use of proper protective equipment,
such as a properly fitted respirator (NIOSH approved) and proper
containment and cleanup. For more information, call the National Lead
Information Center at 1-800-424-LEAD (in US) or contact your local health
authority.
Preparation
To ensure proper adhesion, all surfaces must be clean, dry and free from
dirt, wax, grease, oil, chalk, mildew and loose or peeling paint. Nail holes,
cracks and other surface imperfections should be properly filled, sanded
smooth and dusted clean. All mildew and mold must be completely and
thoroughly removed. Glossy surfaces must be sanded and dusted clean.
Always wear a properly selected and fitted NIOSH/MSHA approved dust
mask or respirator when sanding.
New Wallboard / Drywall
Fill cracks and holes with spackling compound and sand smooth. Joint
compound must be cured and sanded smooth. Remove all sanding dust.
Wood
Sand any exposed wood to a fresh, smooth surface. Patch all holes and
imperfections with a wood filler or putty and sand smooth. Remove all
sanding dust.
Plaster (allow to cure for 30 days)
Must be dry, cured and hard with a pH <9.5. Treat textured, soft, porous or
powdery plaster with a solution of 1 pint of vinegar to 1 gallon of water.
Repeat until surface is hard, rinse with clear water and allow to dry.
Masonry/Aggregate Block (allow to cure for 30 days)
Remove all surface contamination, including heavy chalk, efflorescence,
laitance and concrete dust, by washing with an appropriate cleaner and
allow to dry.
Metal
Wash with an appropriate cleaner to remove any surface contamination.
Remove all corrosion with sandpaper, steel wool or other abrading method.
Prime bare steel the same day as cleaned.
Caulking
Fill gaps between walls, ceilings, crown moldings and other trim with latex
or siliconized latex caulk after priming the surface.
Mildew
Remove before painting by washing with a solution of 1 part liquid bleach
and 3 parts water. Apply the solution and scrub the mildewed area. Allow
the solution to remain on the surface for 10 minutes. Rinse thoroughly with
water and allow the surface to dry before painting. Wear protective
eyewear, waterproof gloves and protective clothing. Quickly wash off any
of the mixture that comes in contact with your skin. DO NOT ADD
DETERGENTS OR AMMONIA TO THE BLEACH/WATER SOLUTION.
Cleanup Information
Clean spills and spatters immediately with soap and warm water. Clean
hands and tools immediately after use with soap and warm water. After
cleaning, flush spray equipment with mineral spirits to prevent rusting of the
equipment. Follow manufacturer’s safety recommendations when using
mineral spirits.
The information and recommendations set forth in this Product
Data Sheet are based upon tests conducted by or on behalf of
Conco Paints. Information and recommendations set forth
herein are subject to change and pertain to the product offered
at the time of publication. Consult your Conco Paint retailer or
sales representative to obtain the most recent Product Data
Sheet.
SERIES
1000
Interior Flat Acrylic Water
Base Wall Paint