CONCEPTRONIC C150APRA2 ENGLISH Conceptronic C150APRA2 Extended User Manual Congratulations on the purchase of your Conceptronic wireless ADSL modem router. This user manual gives you a step-by-step explanation of how to install and use the Conceptronic wireless ADSL modem router. When you need more information or support for your product, we advise you to visit our Service & Support website at www.conceptronic.
CONCEPTRONIC C150APRA2 ENGLISH Table of contents 1. Introduction 1.1 1.2 1.3 2. Safety Precautions Features Package contents The wireless ADSL modem router explained 2.1 2.2 3. Front panel Back panel Hardware Installation 3.1 3.2 4. DSL (Telephone) port LAN port(s) Configuring the computer 4.1 4.2 5. Configure your IP address Checking your connection Modem router configuration 5.1 5.2 5.3 Factory default settings Web-based configuration Setup 5.3.1 5.3.2 5.3.3 5.3.3.1 5.3.3.2 5.3.4 5.
CONCEPTRONIC C150APRA2 5.4.10 5.4.10.1 5.4.10.2 5.4.10.3 5.4.10.4 5.4.10.5 5.4.10.6 5.4.11 5.4.11.1 5.4.11.2 5.4.11.3 5.4.12 5.4.13 5.5 5.6.1 5.6.2 5.6.3 5.6.4 5.6.5 5.6.6 5.6.7 5.
CONCEPTRONIC C150APRA2 ENGLISH 1. Introduction The C150APRA2 supports multiple line modes. It provides four 10/100 base-T Ethernet interfaces at the user end. The device provides high speed ADSL broadband connection to the Internet or Intranet for high-end users, such as net cafes and office users. It provides high performance access to the Internet, downstream up to 24 Mbps and upstream up to 1 Mbps. The device supports WLAN access. It can connect to the Internet through a WLAN AP or WLAN device.
CONCEPTRONIC C150APRA2 1.2 ENGLISH Features The device supports the following features: 802.11b/g/n Various line modes External PPPoE dial-up access Internal PPPoE and PPPoA dial-up access 1483 Bridged, 1483 Routed, and MER access Multiple PVCs (up to eight) that can be isolated from each other A single PVC with multiple sessions Multiple PVCs with multiple sessions Binding of ports with PVCs 802.
CONCEPTRONIC C150APRA2 ENGLISH 2. The wireless ADSL modem router explained 2.
CONCEPTRONIC C150APRA2 2.2 ENGLISH Back panel Nr Description Explanation A B C D E F Antenna connection DSL port LAN ports (1 – 4) Power connector Reset WLAN / WPS button G Power button Connect the included antenna to the modem router. Connect your ADSL line to the modem router. Connect your computer(s)/network device(s) to the modem router. Connect the power supply to the modem router. Perform a factory reset (hold). Short press (1 sec) : Turn WiFi on or off.
CONCEPTRONIC C150APRA2 ENGLISH 3. Hardware Installation Connect the included antenna to the antenna connection [A] on the back of the modem router. Connect the power supply to the power connection [D] on the back of the modem router and to an available wall socket. Press the power [G] button on the back of the modem router. The power LED on the front of the modem router will light up and the modem router will perform a system startup. 3.
CONCEPTRONIC C150APRA2 ENGLISH 4. Configuring the computer 4.1 Configure your IP address The C150APRA2 is equipped with a built-in DHCP server. The DHCP server will automatically assign an IP address to each connected computer if the connected computer is set to ―Obtain an IP address automatically‖. By default most computers are configured to automatically obtain an IP address.
CONCEPTRONIC C150APRA2 ENGLISH The Properties window of the Local Area Connection will appear. D. Select the ―Internet Protocol Version 4 (TCP/IPv4)‖ and click ―Properties‖. D D The Properties window of the Internet Protocol Version 4 (TCP/IPv4) will appear. E. Set the properties to ―Obtain an IP address automatically‖ and press ―OK‖ to save the settings. F. Press ―OK‖ in the properties window of the Local Area Connection to save the settings.
CONCEPTRONIC C150APRA2 4.2 ENGLISH Checking your connection With the Command Prompt of Windows you can verify if you have received a correct IP address on your (wired or wireless) Local Area Connection. This example is based on Windows Vista with Service Pack 1. Windows Vista needs administrative rights to perform the steps below. There is an explanation on how to gain administrative rights. A.
CONCEPTRONIC C150APRA2 ENGLISH 3 3 If above steps do not solve the IP address problem, you can reset the device to the factory default settings with the Reset button on the back of the device. Press and hold the Reset button for +/- 15 seconds to load the factory default settings. When the Status LED is active again, repeat step B to renew your IP address. Note: If the problem remains, check if all cables are connected correctly.
CONCEPTRONIC C150APRA2 ENGLISH 5. Modem router configuration This chapter describes how to configure the C150APRA2 using the built-in Quick Start Wizard. After completing the steps in this chapter your router has been set up for an ADSL connection and will be able to connect to the internet. 5.1 Factory default settings The C150APRA2 is preconfigured with several settings.
CONCEPTRONIC C150APRA2 ENGLISH When the Username and Password are correct the router will display the ―overview‖ page: The ―overview‖ page shows a quick menu for configuring and maintaining the C150APRA2.
CONCEPTRONIC C150APRA2 5.3 ENGLISH Setup In the ―Setup‖ menu, you can configure the basic configuration for your modem router. 5.3.1 Setup - Wizard Wizard helps you to fast and accurately configure Internet connection and other important parameters. The following sections describe these various configuration parameters. When subscribing to a broadband service, be aware of the Internect connection mode. The physical WAN device can be Ethernet, DSL, or both.
CONCEPTRONIC C150APRA2 ENGLISH Step 3 Set the time and date. Then, click Next. Step 4 Configure the Internet connection. Select the country and ISP from the drop-down list. If the Country is set to Belgium, the ISP is set to FullADSL, the Protocol is set to PPPoE or PPPoA, the page as shown in the following figure appears: You need to enter the user name and password for PPPoE or PPPoA dialup.
CONCEPTRONIC C150APRA2 ENGLISH If the Protocol is set to Dynamic IP, the page as shown in the following figure appears: If the Protocol is set to Static IP, the page as shown in the following figure appears: You need to enter the information of the IP address, subnet mask, and gateway.
CONCEPTRONIC C150APRA2 ENGLISH If the Protocol is set to Bridge, the page as shown in the following figure appears: If you click Scan, the system automatically searches the available PVCs. After the searching is complete, the result appears next to the Scan button. After setting, click Next.
CONCEPTRONIC C150APRA2 ENGLISH Step 5 Configure the wireless network. Enter the information and click Next. Step 6 View the configuration information of the device. To modify the information, click Back. To effect the configuration, click Apply.
CONCEPTRONIC C150APRA2 Note: ENGLISH In each step of the Wizard page, you can click Back to review or modify the previous settings or click Cancel to exit the wizard.
CONCEPTRONIC C150APRA2 ENGLISH 5.3.2 Setup - Internet Setup Choose Setup > Internet Setup. The page as shown in the following figure appears: In this page, you can configure the WAN interface of the device.
CONCEPTRONIC C150APRA2 ENGLISH 22
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. ATM PVC CONFIGURATION Field VPI VCI Service Category Description Virtual Path Identifier (VPI) is the virtual path between two points in an ATM network. Its value range is from 0 to 255. Virtual Channel Identifier (VCI) is the virtual channel between two points in an ATM network. Its value range is from 32 to 65535 (0 to 31 is reserved for local management of ATM traffic).
CONCEPTRONIC C150APRA2 ENGLISH 5.3.3 Setup - Wireless This section describes the wireless LAN and some basic configuration. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a pear-to-pear network or as complex as a number of computers with wireless LAN cards communicating through access points that bridge network traffic to a wired LAN. Choose Setup > Wireless. The WIRELESS SETTINGS page as shown in the following figure appears: 5.3.3.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Enable Wireless Enable MultiAP Isolation Wireless Network Name (SSID) Visibility Status Country Wireless Channel 802.11 Mode Band Width Description Select or deselect the check box to enable or disable the wireless function. Select or deselect the check box to enable or disable multiAP isolation. If this function is enabled, clients of different SSIDs cannot access each other. Network name.
CONCEPTRONIC C150APRA2 5.3.3.2 ENGLISH Setup – Wireless - Wireless Security In the WIRELESS SETTINGS page, click Wireless Security. The page as shown in the following figure appears: Wireless security is vital to your network to protect the wireless communication among wireless stations, access points and the wired network. This device provides the following encryption modes: None, WEP, Auto (WPA or WPA2), WPA2 Only, and WPA Only.
CONCEPTRONIC C150APRA2 ENGLISH WEP If the Security Mode is set to WEP, the page as shown in the following figure appears: The following table describes the parameters in this page. Field WEP Key Length Choose WEP Key WEP Keys 1—4 Authentication Description You can select 64 bits or 128 bits from the drop-down list. If you select 64 bits, you need to enter 10 hexadecimal numbers or 5 characters. If you select 128 bits, you need to enter 26 hexadecimal numbers or 13 characters.
CONCEPTRONIC C150APRA2 ENGLISH Auto (WPA or WPA2) If the Security Mode is set to Auto (WPA or WPA2), the page as shown in the following figure appears: The following table describes the parameters in this page. Field WPA Mode Group Key Update Interval Pre-Shared Key Description You can select Auto (WPA or WPA2)-PSK or Auto (WPA or WPA2)-WPA for Enterprise from the drop-down list. Set the interval for updating the key. Set the preshared key to identify the workstation.
CONCEPTRONIC C150APRA2 ENGLISH If the WPA Mode is set to Auto (WPA or WPA2)-Enterprise, the page as shown in the following figure appears: You need to enter the IP address, port, shared key of the RADIUS server. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH WPA2 Only If the Security Mode is set to WPA2 only, the page as shown in the following figure appears: Parameters in this page are similar to those in the page for Auto (WPA or WPA2). Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH WPA Only If the Security Mode is set to WPA only, the page as shown in the following figure appears: Parameters in this page are similar to those in the page for Auto (WPA or WPA2). Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.3.4 Setup - Local Network You can configure the LAN IP address according to the actual application. The preset IP address is 192.168.0.1. You can use the default settings and DHCP service to manage the IP settings of the private network. The IP address of the device is the base address used for DHCP. To use the device for DHCP in your LAN, the IP address pool used for DHCP must be compatible with the IP address of the device.
CONCEPTRONIC C150APRA2 ENGLISH By default, Enable DHCP Server is selected for the LAN interface of the device. DHCP service provides IP settings to workstations configured to automatically obtain IP settings that are connected to the device through the Ethernet port. When the device is used for DHCP, it becomes the default gateway for DHCP client connected to it. If you change the IP address of the device, you must also change the range of IP addresses in the pool used for DHCP on the LAN.
CONCEPTRONIC C150APRA2 ENGLISH 5.3.5 Setup - Time and Date Choose Setup > Time and Date. The TIME AND DATE page as shown in the following figure appears: In the TIME AND DATE page, you can configure, update, and maintain the time of the internal system clock. You can set the time zone that you are in and the network time protocol (NTP) server. You can also set daylight saving time to automatically adjust the time when needed. Select Automatically synchronize with Internet time servers.
CONCEPTRONIC C150APRA2 ENGLISH 5.3.6 Setup - Logout Choose Setup > Logout. The page as shown in the following figure appears: Click Logout to log out of the configuration page.
CONCEPTRONIC C150APRA2 5.4 ENGLISH Advanced This section contains advanced features used for network management, security and administrative tools to manage the device. You can view the status and other information of the device, to examine the performance and troubleshoot. 5.4.1 Advanced – Port Forwarding This function is used to open ports in your device and re-direct data through these ports to a single PC in your network (WAN-to-LAN traffic).
CONCEPTRONIC C150APRA2 ENGLISH Select a service for a preset application or enter the name in the Custom Server field. Enter an IP address in the Server IP Address field, to appoint the corresponding PC to receive forwarded packets. The port table displays the ports that you want to open on the device. The Protocol indicates the type of protocol used by each port.
CONCEPTRONIC C150APRA2 ENGLISH Click Apply to save the settings. The page as shown in the following figure appears. A virtual server is added.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.2 Advanced – Advanced Wireless This function is used to modify the standard 802.11g wireless settings. It is recommended not changing the default settings, because incorrect settings may affect the performance of the wireless performance. The default settings provide the best wireless performance in most environments. Choose Advanced > Advanced Wireless.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.2.1 Advanced – Advanced Wireless – Advanced Settings In the ADVANCED WIRELESS page, click Advanced Settings.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. ADVANCED WIRELESS SETTINGS Field Transmission Rate Multicast Rate Transmit Power Beacon Period RTS Threshold Fragmentation Threshold DTIM Interval Preamble Type Description Select the transmission rate of the wireless network from the drop-down list. Select the multicast transmission rate of the wireless network from the drop-down list. You can select Lower or Higher.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.2.2 Advanced – Advanced Wireless – MAC Filtering In the ADVANCED WIRELESS page, click MAC Filtering.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field User Name Current PC’s MAC Address Other MAC Address Schedule Manual Schedule Description Enter the name that identifies your configuration. For example, kids. Enter the MAC address of the computer that connects to the device. Enter the MAC address of another device that is included in MAC filtering. Select the time of MAC filter from the drop-down list. You can select always or never.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.2.3 Advanced – Advanced Wireless – Security Settings In the ADVANCED WIRELESS page, click Security Settings. The page as shown in the following figure appears: Select the desired SSID from the drop-down list. Select the encryption type from the Security Mode drop-down list. You can select None, WEP, AUTO (WPA or WPA2), WPA Only, or WPA2 Only. For parameters of different encryption types, see section Error! Reference source not found. "Error! Reference source not found.
CONCEPTRONIC C150APRA2 5.4.2.4 ENGLISH Advanced – Advanced Wireless – WPS Settings In the ADVANCED WIRELESS page, click WPS Settings. The WIRELESS WPS page as shown in the following figure appears: Enabled: The WPS service is enabled by default. Note: Ensure that the network card supports the WPS function. You can use one of the following there methods to use WPS authentication: Press the WPS button on the side panel for 3 seconds. In the WIRELESS WPS page, click PBC.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.3 Advanced – DMZ Choose Advanced > DMZ. The page as shown in the following figure appears: In this page, you can enable a DMZ host. In this way, access from Internet to the WAN IP address of the device is forwarded to the DMZ host and network server of the internal LAN is protected. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.4 Advanced – Parental Control Choose Advanced > Parental Control. The PARENTAL CONTROL page as shown in the following figure appears: This page provides two useful tools for restricting Internet access. Block Website allows you to quickly create a list of websites that you wish to prevent users from accessing. Block MAC Address allows you to control Internet access by clients or PCs connected to the device.
CONCEPTRONIC C150APRA2 5.4.4.1 ENGLISH Advanced – Parental Control - Block Website In the PARENTAL CONTROL page, click Block Website. The page as shown in the following figure appears: Click Add.
CONCEPTRONIC C150APRA2 ENGLISH Enter the website in the URL field. Select the time to block websites from the Schedule drop-down list, or select Manual Schedule and set the corresponding time and days. Click Submit to add the website to the BLOCK WEBSITE table.
CONCEPTRONIC C150APRA2 5.4.4.2 ENGLISH Advanced – Parental Control – Block MAC Address In the PARENTAL CONTROL page, click Block MAC Address. The page as shown in the following figure appears: Note: The Block MAC Address feature from the PARENTAL CONTROL page refers to the MAC Filtering from the ADVANCED SETTINGS page. The following table describes the parameters in this page.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.5 Advanced – Filtering Options Choose Advanced > Filtering Options.
CONCEPTRONIC C150APRA2 5.4.5.1 ENGLISH Advanced – Filtering Options – Inbound IP Filtering In the FILTERING OPTIONS page, click Inbound IP Filtering. The INCOMING IP FILTERING page as shown in the following figure appears: Click Add to add an inbound IP filter.
CONCEPTRONIC C150APRA2 ENGLISH Enter the Filter Name and specify at least one of the following criteria: protocol, source/destination IP address, subnet mask, and source/destination port. Click Apply to save the settings. Note: The settings apply only when the firewall is enabled. The ACTIVE INBOUND FILTER in the INCOMING IP FILTERING page displays detailed information of each created inbound IP filter. Click Delete to delete an IP filter.
CONCEPTRONIC C150APRA2 5.4.5.2 ENGLISH Advanced – Filtering Options – Outbound IP Filtering By default, all outgoing IP traffic from the LAN is allowed. The outbound filter allows you to create a filter rule to block outgoing IP traffic by specifying a filter name and at least one criterion. In the FILTERING OPTIONS page, click Outbound IP Filtering. The OUTGOING IP FILTERING page as shown in the following figure appears: Click Add to add an outbound IP filter.
CONCEPTRONIC C150APRA2 ENGLISH Enter the Filter Name and specify at least one of the following criteria: protocol, source/destination IP address, subnet mask, and source/destination port. Click Apply to save the settings. The ACTIVE OUTBOUND FILTER in the OUTGOING IP FILTERING page displays detailed information OF each created outbound IP filter. Click Delete to delete an IP filter. Note that the Delete button appears only when at least one IP filter exists.
CONCEPTRONIC C150APRA2 5.4.5.3 ENGLISH Advanced – Filtering Options – Bridge Filtering In the FILTERING OPTIONS page, click Bridge Filtering. The page as shown in the following figure appears: This page is used to configure bridge parameters. In this page, you can modify the settings or view the information of the bridge and its attached ports. Click Add to add a bridge filter.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Protocol Type Destination MAC Address Source MAC Address Frame Direction Time schedule Wan interface Description Select the protocol type to be mapped from the drop-down list. You can select PPPoE, IPv4, IPv6, AppleTalk, IPX, NetBEUI, or IGMP. Enter the destination MAC address to be mapped. Enter the source MAC address to be mapped. Select the frame direction to be mapped from the drop-down list.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.6 Advanced – QOS Config Choose Advanced > QoS Config.
CONCEPTRONIC C150APRA2 5.4.6.1 ENGLISH Advanced – QOS Config – QOS Interface Config In the QoS CONFIG page, click QoS Interface Config.
CONCEPTRONIC C150APRA2 ENGLISH In this page, you can configure the uplink bandwidth and downlink bandwidth of each interface. The uplink rate and the downlink rate are limited according to the configured bandwidth. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 5.4.6.2 ENGLISH Advanced – QOS Config – QOS Queue Config In the QoS CONFIG page, click Qos Queue Config. The page as shown in the following figure appears: In this page, you can configure the priority of the queue. The device supports the following three priority levels: high, medium, low. The device handles packets of the high queue priority first, then packets of medium, and finally packets of low priority. Click Add.
CONCEPTRONIC C150APRA2 ENGLISH Click Apply to save the settings.
CONCEPTRONIC C150APRA2 5.4.6.3 ENGLISH Advanced – QOS Config – QOS Classify Config In the QoS CONFIG page, click QoS Classify Configuration. The page as shown in the following figure appears: This page displays the classes.
CONCEPTRONIC C150APRA2 ENGLISH 64
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Traffic Class Name Enable Classification Description Enter the name of the traffic class. Select or deselect the check box to enable or disable QoS classification. SPECIFY TRAFFIC CLASSIFICATION RULES Field Classification Type Physical Lan Port Description Select L1&L2 or L3&L4 from the drop-down list. L1&L2 maps to the features of layer 1 and layer 2, such as the MAC address.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.7 Advanced – Firewall Settings A denial-of-service (DoS) attack is one of the most common network attacks and is characterized by an explicit attempt by attackers to prevent legitimate users of a service from using that service. It usually leads to overload of system server or core dump of the system. Choose Advanced > Firewall Settings. The page as shown in the following figure appears: Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.8 Advanced – DNS Domain name system (DNS) is an Internet service that translates domain names into IP addresses. Because domain names are alphabetic, they are easier to remember. The Internet, however, is actually based on IP addresses. Each time you use a domain name, a DNS service must translate the name into the corresponding IP address. For example, the domain name www.example.com might be translated to 198.105.232.4. The DNS system is, in fact, its own network.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Obtain DNS server address automatically Use the following DNS server addresses WAN Connection Description If you select this radio button, the device automatically obtains IP address of the DNS server from the ISP. You need not manually enter the IP address of the server. If you select this radio button, you need to manually enter the IP address of the server provided by the ISP.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.9 Advanced – Dynamic DNS The device supports dynamic domain name service (DDNS). The dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains, and allows access to a specified host from various locations on the Internet. Click a hyperlinked URL in the form of hostname.dyndns.org and allow remote access to a host.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field DDNS provider Hostname Interface Description Select the DDNS provider from the drop-down list. You can select DynDns.org, TZO, or GnuDIP. Enter the host name that you register with your DDNS provider. Select the interface that is used for DDNS service from the dropdown list. The IP address of the interface corresponds to the host name. Username Enter the user name of your DDNS account.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10 Advanced – Network Tools Choose Advanced > Network Tools.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.1 Advanced – Network Tools – Port Mapping In the NETWORK TOOLS page, click Port Mapping. The page as shown in the following figure appears: In this page, you can bind the WAN interface and the LAN interface to the same group. Click Add to add port mapping.
CONCEPTRONIC C150APRA2 ENGLISH To create a mapping group, do as follows: Step 1 Step 2 Step 3 Enter the group name. Select interfaces from the Available Interfaces list and click the <- arrow button to add them to the grouped interface list, in order to create the required mapping of the ports. The group name must be unique. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.2 Advanced – Network Tools – IGMP Proxy In the NETWORK TOOLS page, click IGMP Proxy. The page as shown in the following figure appears: IGMP proxy enables the device to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The device serves as a proxy for its hosts after you enable the function. Select Enable IGMP Proxy and select the desired WAN and corresponding LAN interface. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.3 Advanced – Network Tools – IGMP Snooping When IGMP snooping is enabled, only hosts that belong to the group receive the multicast packets. If a host is deleted from the group, the host cannot receive the multicast packets any more. In the NETWORK TOOLS page, click IGMP Snooping. The page as shown in the following figure appears: Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.4 Advanced – Network Tools – UPnP In the NETWORK TOOLS page, click Upnp. The page as shown in the following figure appears: In this page, you can enable universal plug and play (UPnP) and then the system serves as a daemon. UPnP is widely applied in audio and video software. It automatically searches devices in the network. If you are concerned about UPnP security, you can disable it.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.5 Advanced – Network Tools – ADSL In the NETWORK TOOLS page, click ADSL. The page as shown in the following figure appears: In this page, you can select the ADSL modulation. Normally, you are recommended to keep the factory defaults. The device supports the following modulation types: G.Dmt, G.lite, T1.413, ADSL2, AnnexL, ADSL2+, and AnnexM. The device negotiates the modulation mode with the DSLAM. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.10.6 Advanced – Network Tools – SNMP In the NETWORK TOOLS page, click SNMP. The page as shown in the following figure appears: In this page, you can set the SNMP parameters. The following table describes the parameters in this page. Field Enable SNMP Agent Read Community Set Community Description Select or deselect the check box to enable or disable SNMP agent. Universal character to obtain the device information. It is similar to the password.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.11 Advanced – Routing Choose Advanced > Routing. The page as shown in the following page appears: This page contains the following function items: static route, default gateway, and RIP settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.11.1 Advanced – Routing – Static Routing Choose Advanced > Routing and click Static Route. The page as shown in the following figure appears: This page displays the information of existing static routes.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Destination Network Address Subnet Mask Use Gateway IP Address Use Interface Description The destination IP address of the device. The subnet mask of the destination IP address. The gateway IP address of the device. Select the interface of the static routing used by the device from the drop-down list.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.11.2 Advanced – Routing – Default Gateway Choose Advanced > Routing and click Default Gateway. The page as shown in the following figure appears: In this page, you can select Enable Automatic Assigned Default Gateway, or enter the information in the Use Gateway IP Address and Use Interface fields. Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.11.3 Advanced – Routing – RIP Choose Advanced > Routing and click RIP. The page as shown in the following figure appears: In this page, you can view the interfaces on your device that use RIP and the version of the protocol used. If you enable RIP, the device communicates with other devices using the routing information protocol (RIP). Click Apply to save the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.4.12 Advanced – Schedules Choose Advanced > Schedules. The page as shown in the following figure appears: Click Add to add a schedule rule.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. Field Name Day(s) All Day – 24 hrs Description Set the name of the schedule. You can select one, more, or all of the seven days in a week. If you select the check box, the rule applies throughout the 24 hours of the day. Start Time Set the start time of the firewall. End Time Set the end time of the firewall. Click Apply to save the settings. 5.4.13 Advanced – Logout Choose Advanced > Logout.
CONCEPTRONIC C150APRA2 5.5 ENGLISH Management 5.5.1 Management – System Management Choose Management > System Management. The System page as shown in the following figure appears: In this page, you can restart the device, back up the current settings to a file, update the backup file, and restore the factory default settings. The following table describes the buttons in this page. Button Description Reboot Restart the device.
CONCEPTRONIC C150APRA2 ENGLISH 5.5.2 Management – Firmware Update Choose Management > Firmware Update. The page as shown in the following figure appears: In this page, you can upgrade the firmware of the device. To update the firmware, do as follows: Step 1 Step 2 Click Browse…to select the file. Click Update Firmware to update the configuration file. The device loads the file and reboots automatically.
CONCEPTRONIC C150APRA2 ENGLISH 5.5.3 Management – Access Controls Choose Management > Access Controls. The ACCESS CONTROLS page as shown in the following figure appears: This page contains Account Password, Services, and IP Address.
CONCEPTRONIC C150APRA2 5.5.3.1 ENGLISH Management – Access Controls – User Management In the ACCESS CONTROLS page, click Account Password. The page as shown in the following figure appears: In this page, you can change the password and set the time for automatic logout. You are recommended to change the default password to ensure the security of your network. Ensure that you remember the new password or write it down and keep it in a safe location for future reference.
CONCEPTRONIC C150APRA2 ENGLISH The following table describes the parameters in this page. ACCOUNT PASSWORD Field Current Password New Password Description Select a user name from the drop-down list to access the device. You can select admin. Enter the password of the user. Enter the new password. Confirm Password Enter the new password again for confirmation.
CONCEPTRONIC C150APRA2 5.5.3.2 ENGLISH Management – Access Controls – Services In the ACCESS CONTROLS page, click Services. The page as shown in the following figure appears: In this page, you can enable or disable the services that are used by the remote host. For example, if telnet service is enabled at port 23, the remote host can access the device by telnet through port 23.
CONCEPTRONIC C150APRA2 5.5.3.3 ENGLISH Management – Access Controls – IP Address In the ACCESS CONTROLS page, click IP Address. The page as shown in the following figure appears: In this page, you can configure the IP address in the access control list (ACL). If ACL is enabled, only devices of the specified IP addresses can access the device. Select Enable Access Control Mode to enable ACL. Note: If you enable ACL, ensure that the IP address of the host is in the ACL list.
CONCEPTRONIC C150APRA2 ENGLISH Click Add. The page as shown in the following figure appears: Enter the IP address of the desired device in the IP Address field and click Apply to apply the settings.
CONCEPTRONIC C150APRA2 ENGLISH 5.5.4 Management – Diagnosis Choose Management > Diagnosis. The page as shown in the following figure appears: In this page, you can test the connection status of the device. Click Return Diagnostics Test to run diagnostics. The page as shown in the following figure appears: Note: The above diagnostics information is an example. In your situation, the results can be different.
CONCEPTRONIC C150APRA2 ENGLISH 5.5.5 Management – Log Configuration Choose Management > Log Configuration. The SYSTEM LOG page as shown in the following figure appears: In this page, you can enable the log function. You can set Mode to Local, Remote, or Both. Local indicates to save the log in the local computer. Remote indicates to send the log to the remote log server. Both indicates to save the log in the local computer and the remote log server.
CONCEPTRONIC C150APRA2 5.5.6 ENGLISH Management – Logout Choose Management > Logout. The page as shown in the following figure appears: Click Logout to log out of the configuration page.
CONCEPTRONIC C150APRA2 5.6 ENGLISH Status In the Status page, you can view the system information and monitor the performance of the device. 5.6.1 Status – Device Info Choose Status > Device Info. The page as shown in the following figure appears: The page displays the summary of the device status, including the system information, WAN connection information, wireless information, and local network information.
CONCEPTRONIC C150APRA2 ENGLISH 5.6.2 Status – Wireless Clients Choose Status > Wireless Clients. The page as shown in the following page appears: The page displays authenticated wireless stations and their statuses. 5.6.3 Status – DHCP Clients Choose Status > DHCP Clients. The page as shown in the following page appears: This page displays all client devices that obtain IP addresses from the device. You can view the host name, IP address, MAC address, and expiration time of the IP address.
CONCEPTRONIC C150APRA2 ENGLISH 5.6.4 Status – Logs Choose Status > Logs. The page as shown in the following figure appears: This page displays the system log. Click Refresh to refresh the system log shown in the box.
CONCEPTRONIC C150APRA2 ENGLISH 5.6.5 Status – Statistics Choose Status > Statistics. The page as shown in the following figure appears: This page displays the statistics information of the network and data transmission. The information helps technicians to identify whether the device is functioning properly. The information does not affect the functions of the device.
CONCEPTRONIC C150APRA2 ENGLISH 5.6.6 Status – Route Info Choose Status > Route Info. The page as shown in the following figure appears: The table displays destination routes commonly accessed by the network. 5.6.7 Status – Logout Choose Staus > Logout. The page as shown in the following figure appears: Click Logout to log out of the configuration page.
CONCEPTRONIC C150APRA2 5.7 ENGLISH Help The Help menu will help you with information about all the items in the configuration of the device.
CONCEPTRONIC C150APRA2 ENGLISH 6. Frequently Asked Questions Below you will find some frequently asked questions for the device.
CONCEPTRONIC C150APRA2 ENGLISH 7. License Information This Conceptronic product C150APRA2 includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please see The GNU General Public License for the exact terms and conditions of this license. Availability of source code Conceptronic. has eposed the full source code of the GPL licensed software, including any scripts to control compilation and installation of the object code.
CONCEPTRONIC C150APRA2 ENGLISH GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
CONCEPTRONIC C150APRA2 ENGLISH 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
CONCEPTRONIC C150APRA2 ENGLISH NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
CONCEPTRONIC C150APRA2 ENGLISH GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
CONCEPTRONIC C150APRA2 ENGLISH GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
CONCEPTRONIC C150APRA2 ENGLISH 4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
CONCEPTRONIC C150APRA2 ENGLISH 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9.
