ENGLISH Conceptronic ADSL Router User’s manual Table of contents Chapter Chapter 1 Chapter 2 Chapter 3 Chapter 4 Appendix A Description Introduction Using the ADSL Router Configuration Troubleshooting Specifications Page number 1 4 6 48 49 Chapter 1: Introduction 1.1 An Overview of the ADSL Router The ADSL Router provides a high-speed ADSL port and an Ethernet port for high-speed Internet browsing.
ENGLISH 5. RS-232 Cable 6. Power adapter (5V, 2.6A DC) 1.3 The ADSL Router Features The ADSL Router provides the following features: ADSL Multi-Mode Standard: Supports downstream transmission rates of up to 8Mbps and upstream transmission rates of up to 1024Kbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt(G.992.1); G.lite(G992.2)).
ENGLISH 1.
ENGLISH Chapter 2: Using the ADSL Router 2.1 Cautions for using the ADSL Router Do not place the ADSL Router under high humidity and high temperature. Do not use the same power source for the ADSL Router with other equipment. Do not open or repair the case yourself. If the ADSL Router is too hot, turn off the power immediately and have a qualified serviceman repair it. Place the ADSL Router on the stable surface. Only use the power adapter that comes with the package. 2.
ENGLISH 2.3 The Rear Ports Port Meaning 1 Power (jack) Connect the supplied power adapter to this jack. 2 LAN (RJ-45 connector) Connect an UTP Ethernet cable to this port when connecting to a LAN such as an office or home network. Connect a crossover cable (provided with this package) to this port when connecting to a LAN card. 3 RS-232 (port) Connect the supplied RS-232 cable to this port when connecting to a PC’s RS-232 port (9-pin serial port).
ENGLISH Chapter 3: Configuration The ADSL Router can be configured with your Web browser. The web browser is included as a standard application in following operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/ME, etc. The product provides a very easy and user-friendly interface for configuration. 3.1 Before Configuration This section describes the configuration required by LAN-attached PCs that communicate with the ADSL Router, either to configure the device, or for network access.
ENGLISH 4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration.
ENGLISH Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
ENGLISH Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click LAN Area Connection. 3. In the LAN Area Connection Status window, click Properties.
ENGLISH 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
ENGLISH Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections. 2. Double-click Local Area Connection. 3. In the LAN Area Connection Status window, click Properties.
ENGLISH 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
ENGLISH 3.2 Factory Default Settings Before you configure the ADSL Router, you need to know the following default settings. 1. Web Configurator Password : BLANK means user does not need to input any characters. 2. Device IP Network settings in LAN site IP Address : 192.168.1.254 Subnet Mask : 255.255.255.0 3. Router/Bridge mode Router 4. ISP setting in WAN site PPPoE 5. DHCP server DHCP server is enabled. Start IP Address : 192.168.1.100 IP pool counts : 100 3.2.
ENGLISH If you ever forget the password to log in, you should contact the dealer where you bought this product. 3.2.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 PPPoE function is enabled to automatically get the WAN port configuration from ISP, but you have to set username and password first. Subnet Mask 255.255.255.
ENGLISH 3.4 Configuring with Web Browser in Router Mode Open the web browser, enter the local port IP address of the ADSL Router, which default at 192.168.1.254, and click “Go” to get the login page. No user name is required. The default password is left blank. If you have set a password, enter that and click “OK” to continue.
ENGLISH 3.4.1 LAN This screen contains settings for LAN interface attached to the LAN port. IP Address IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan to change it to another IP address to a different range of IP subnet. Please make sure your PC is also located at the same IP subnet. Otherwise, you may not be able to access the ADSL Router. Subnet Mask: Default at 255.255.255.0.
ENGLISH If you check this selection, Disable, remember to specify a static IP address, subnet Mask, and DNS setting for each of your local computers. Be careful not to assign the same IP address to different computers. ¤ Enable: Check to enable the ADSL Router to distribute IP Addresses, subnet mask and DNS setting to computers. Hence, the following fields will be activated. Starting IP Address: Enter the starting address of this local IP network address pool.
ENGLISH PPPoE PPPoE (PPP over Ethernet) is known as a dial-up DSL or cable service. It is designed to integrate the broadband services into the current widely deployed, easy-to-use, and low-cost dial-up-access networking infrastructure. Therefore, users can get greater access speed without changing the operation concept, sharing the same ISP account and paying for one access account. No PPPoE client software is required for local computer if you select this configuration.
ENGLISH PPPoA NAT: The NAT feature allows multiple users to access Internet through a single IP account, sharing the single IP address from ISP. If users in the LAN site have public IP addresses and can access Internet directly, the NAT function can be disabled. Username: Enter the username provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive). Password: Enter the password provided by your ISP. Maximum input is 63 alphanumeric characters (case sensitive).
ENGLISH Configure this WAN interface with a specific IP address. This IP address should be given from ISP directly. NAT: The NAT feature allows multiple users to access Internet through a single IP account, sharing the single IP address from ISP. If users in the LAN site have public IP addresses and can access Internet directly, the NAT function can be disabled. IP Address: Enter the information provided by your ISP. Subnet Mask: Enter the information provided by your ISP.
ENGLISH DNS A Domain Name System (DNS) contains a mapping table for domain name and IP address. In the Internet, every host has a unique and friendly name such as www.yahoo.com and IP address. The IP address is very hard to remember, so that you may just enter the friendly name www.yahoo.com and DNS converts it to its equivalent IP address. You can obtain Domain Name System (DNS) IP address automatically if ISP provides it when you logon.
ENGLISH 3.4.3 System Password In factory setting, there is no password protection when user accesses the ADSL Router. It is recommended that you change the default password to ensure that someone cannot adjust your settings without your permission. means there is no password. Every time you change your password, please record the password and keep it at a safe place. Please note that the maximum input for password is 8 alphanumeric characters long.
ENGLISH Time Zone The ADSL Router does not have a real time clock on board; instead, it uses the simple network time protocol (SNTP) to get the current time from the SNTP server in outside network. Please choose your local time zone and click Apply button. You will get the correct time information after you really establish a connection to Internet. The current time of selected time zone will be shown in the Status – System window.
ENGLISH Factory Setting If for any reason, you have to reset this ADSL Router back to factory default settings , be careful that the current settings will be lost and the settings are reset back to its default state. The factory default values is detailed in section 3.2 ‘‘Factory Default Settings’’. Reboot In case the device stops responding correctly or in some other way stops functioning, you can perform the reboot. Your setting won’t be changed. Performing the reboot, click on the Reboot button.
ENGLISH 3.4.4 Firewall User can decide to enable this firewall function including Packet Filter, Block Hacker Attack, and Block WAN request features for better security control or not. But be noted, it wastes network processor computation power. The performance will be lower about 5% to 10%. More firewall features will be added continually, please visit our web site to download latest firmware.
ENGLISH This configuration program allows you to set up different filter rules up to 20 for different users based on their IP addresses or their network Port number. The relationship among all filters is “or” operation, which means the router checks these different filter rules one by one, stating from the first rule. As long as one of the rules is satisfied, the specified action will be taken. Add: Click this button to add a new packet filter rule. After click, next figure will appear.
ENGLISH Packet Type: Specify the packet type (TCP, UDP, ICMP or any) that the rule will be applied to. Select TCP if you want to scope for the connection-based application service on the remote server using the port number. Or select UDP if you want to scope for the connectionless application service on the remote server using the port number. Log: Choose “Yes” if you want to generate logs when the filer rule is applied to a packet.
ENGLISH - Sync flooding - Smurf Attack (ICMP Echo with x.x.x.0 or x.x.x.255) - Snork Attack - UDP port loop-back - TCP NULL scan Block WAN Request Check “Enable” if you want to exclude outside PING from reaching on this router. 3.4.5 VPN VPN (Virtual Private Network) is a secured and Internet protocol to allow users to access the company internal network resources outside the company network. If you want to make this function take effect, check the “Enable” button.
ENGLISH Username: Enter the username. Maximum input is 63 alphanumeric characters (case sensitive). Password: Enter the password. Maximum input is 63 alphanumeric characters (case sensitive). Server IP Address: Enter the IP address of the PPTP Server. You can obtain Domain Name System (DNS) IP address automatically if PPTP server provides it when you logon. Or your remote PPTP server may provide you with an IP address of DNS. If this is the case, you must enter the DNS IP address provided.
ENGLISH 3.4.6 Virtual Server Being a natural Internet firewall, the ADSL Router protects your network from being accessed by outside users. When it needs to allow outside users to access internal servers, e.g. Web server, FTP server, E-mail server or News server, this product can act as a virtual server. You can set up a local server with specific port number that stands for the service, e.g. Web (80), FTP (21), Telnet (23), SMTP (25), POP3 (110), DNS (53), ECHO (7), NNTP (119).
ENGLISH 3.4.7 Advanced Remote Config Check “Enable” if you want to configure your ADSL Router from any PC in the Internet world with a web browser. To configure this router remotely, use the URL ”http://WAN IP address:33659” where WAN IP address is the IP address of the router’s WAN port. You can find the value in the System Status. “33659” is the default port number; please use your own port if you change the default value.
ENGLISH Dynamic Routing The dynamic routing function of the router can be used to allow the router to automatically adjust to physical changes in the network’s layout. The router uses the dynamic RIP protocol. It regularly broadcasts routing information to other routers on the network. Choose the protocol - RIP1, RIP2, or RIP1+RIP2 - you want the router to use to transmit / receive data on / from the network.
ENGLISH Static Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet. After you check the “Enable” radio button, the following figure will appear. Add: Click this button to add a new static routing. When you click this button, the next figure appears. Edit: Check the item you want to edit. Then, click the “Edit” button. Delete: Check the item you want to delete. Then, click the “Delete” button.
ENGLISH Destination Subnet / Subnet Mask / Gateway Address: Fill in these fields required by this Static Routing function. Router/Bridge Mode Switch off between router and bridge mode.
ENGLISH 3.4.8 Status System Status Display the current LAN, WAN, and ADSL connection status. The first line under the WAN segment displays the WAN-ISP protocol you set. You can see the status of connection from its right-side column. As for “PPPoE” and “PPPoA” protocol, the right column seems some kind different. There is a button beside the connection status. When the PPPoE/PPPoA status is disconnected, you can click the “Connect” button to logon your ISP.
ENGLISH Device Info Display the current Firmware version and MAC address of your ADSL Router. System Logs Display the system logs cumulated till the present time. You can trace the historical information through this function. Refresh / Clear: Click “Refresh” to get the latest information of system logs, or click “Clear” to eliminate all the system logs showed on this screen.
ENGLISH Security Logs Display the information of security logs. If hacker attacks your sever, he will be isolated by the firewall function and the router will record related information. Hence, you know where the hacker comes from. Refresh: Click “Refresh” to get the latest information of system logs. DHCP Table Display the IP addresses allocation information in DHCP server. Please refer to the “DHCP Server” part in section 3.4.1.
ENGLISH 3.4.9 Help After click on the hyperlink of “Help” in the left pane, the following html page will jump out. This page would be a good reference as you precede the configuration. 3.5 Configuring with Web Browser in Bridge Mode Open the web browser, enter the local port IP address of this ADSL Router, which default at 192.168.1.254, and click “Go” to get the login page. No user name is required. The default password is left blank. If you have set a password, enter that and click “OK” to continue.
ENGLISH Click on the desired item to expand the page in the main navigation pane. 3.5.1 LAN This screen contains settings for LAN interface attached to the LAN port. IP Address: Default at 192.168.1.254. This is the device IP address in LAN site. If you plan to change it to another IP address to a different range of IP subnet. Please make sure your PC is also located at the same IP subnet. Otherwise, you may not be able to access the ADSL Router. Subnet Mask: Default at 255.255.255.0. 3.5.
ENGLISH Protocol: There are two ways - RFC1483 and PPTP-to-PPPoA Relaying You have to check with your ISP about which way is adopted. for the device to have a public IP address. VPI/VCI: Consult the telephone company to get the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers. The valid range for the VPI is 0 to 255 and for the VCI is 32 to 65535. The default value VPI is 0 and VCI is 32.
ENGLISH Upgrade To upgrade the firmware of the ADSL Router, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedure is completed, the bridge will reset automatically to make the new firmware work.
ENGLISH In case the device stops responding correctly or in some other way stops functioning, you can perform the reboot. Your setting won’t be changed. Performing the reboot, click on the Reboot button. Each time you reboot your ADSL Router, the following figure will appear. Please wait 25 seconds for auto-reconnection.
ENGLISH 3.5.4 Advanced Remote Config Check “Enable” if you want to configure your ADSL Router from any PC in the Internet world with a web browser. To configure this device remotely, use the URL “http://LAN IP address” where LAN IP address is the IP address of the device’s LAN port. You can find the value in the System Status. Router/Bridge Mode Switch off between router and bridge mode.
ENGLISH 3.5.5 Status System Status Display the current LAN, WAN, and ADSL connection status. The first line under the WAN segment displays the WAN-ISP protocol you set. This page will refresh automatically every 15 seconds, which enables you to get the most updated status of your system. You can also click the “Refresh” button to get the latest information of system status manually. Device Info Display the current Firmware version and MAC address of your ADSL Router.
ENGLISH System Logs Display the system logs cumulated till the present time. You can trace the historical information through this function. Refresh / Clear: Click “Refresh” to get the latest information of system logs, or click “Clear” to eliminate all the system logs showed on this screen. 3.5.6 Help After click on the hyperlink of “Help” in the left pane, the following html page will jump out. This page would be a good reference as you precede the configuration.
ENGLISH 3.6 Changing Password In factory setting, there is no password protection when user accesses the ADSL Router. It is recommended that you change the default password to ensure that someone cannot adjust your settings without your permission. means there is no password. Every time you change your password, please record the password and keep it at a safe place. Please note that the maximum input for password is 8 alphanumeric characters long.
ENGLISH To upgrade the firmware of the ADSL Router, you should download or copy the firmware to your local environment first. Press the “Browse…” button to specify the path of the firmware file. Then, click “Upgrade” to start upgrading. When the procedure is completed, the router will reset automatically to make the new firmware work.
ENGLISH CHAPTER 4: TROUBLESHOOTING If the ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems Starting Up the ADSL Router Problem Corrective Action None of the LEDs are on when you turn on the ADSL Router. Check the connection between the AC adapter and the ADSL Router.
ENGLISH APPENDIX A: SPECIFICATIONS Protocols IP, NAT, PPTP, ARP, ICMP, DHCP, PPPoE, PPPoA, IPoA, PPTP client, RIP1/2 LAN Port RJ-45, 1 ports 10/100Base-T WAN Port RJ-11, 1 ADSL port LED Indicators PPP, LAN-ACT, LAN-COL, ADSL, Power Input Power 5V DC @2.