Operating instructions
Remove  excess  water  from  the  reservoir 
by lifting  the  unit,  inverting  and pouring  the 
unit  over  sink,  and  allowing  water  to  drain 
from  internal  reservoir.  Repeat  the  above 
procedure as many times as necessary until a 
normal steam rate returns, usually 2-3 times. 
With each repeated cycle, use a fresh solution 
of vinegar and water. Run one cycle of fresh, 
cold water through the unit at the completion 
of decalcification, before using the unit again 
to steam garments.
HOW TO STEAM 
Grasp the T-handle  steam nozzle with  the 
steam  jets  facing  away  from  you.  Begin 
at  the  bottom  of  the  fabric  to  allow  the 
steam  to  rise  inside  and outside,  removing  
wrinkles. Slowly  move  the nozzle  from  the 
bottom to the top of the  fabric. Remove  the 
nozzle from the garment and smooth the fab-
ric with your free hand. Some fabrics are best 
steamed on the underside  of the material. 
This will allow the fibers of the fabric to relax, 
eliminating wrinkles.
NOTE:  Test fabric  for color  fastness in an 
inconspicuous  spot.  Drape  linens,  towels, 
handkerchiefs  and  napkins  over  a  rod  or 
place on a towel rack.
Heavier fabrics may require repeated steam-
ing. Repeat as necessary.
With  practice,  you  will  gain  speed  and  
efficiency. You  will  soon  learn  which  fabrics 
require multiple steam applications.
Do not  directly  touch  velvet  or silk  with  the 
steam head.
TROUBLESHOOTING
•  PROBLEM - Steamer fails to heat 
  CAUSE - Steamer not plugged in 
  SOLUTION - Plug into electrical outlet
•  PROBLEM - No steam 
  CAUSE - Water level is low 
  SOLUTION - Turn On/Off switch off and  
  refill water container
•  PROBLEM - Water drips from nozzle  
  CAUSE - Condensation in hose 
  SOLUTION - Hold the hose vertically
  and allow water to drain back into unit
•  PROBLEM - Nozzle gurgles 
  CAUSE - Condensation in hose 
  SOLUTION - Hold the hose vertically 
  and allow water to drain back into unit
•  PROBLEM - Poor steam performance  
  CAUSE - Sediment in container 
  SOLUTION - Decalcify reservoir and water  
  container
Note: Minerals in water will vary in different 
areas. To insure continued operation of 
the steamer, never store without cleaning 
and removing excess water from the  
reservoir and water container.
LIMITED ONE-YEAR WARRANTY
Conair will repair  or  replace  (at  our option) 
your unit free of charge for 12 months from 
the date of purchase if the appliance is defective 
in workmanship or materials.
To obtain service under this warranty, return the 
defective product to the service centre listed 
below,  together  with  your purchase  receipt 
and  $5.50  for  postage  and  handling.  In  the 
absence  of  a  purchase receipt,  the warranty 
period  shall  be  12  months  from  the  date  of 
manufacture.
ANY IMPLIED WARRANTIES, INCLUDING BUT 
NOT LIMITED TO THE IMPLIED WARRANTY 
OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE, SHALL BE LIMITED 
IN DURATION TO THE 12-MONTH DURATION 
OF THIS WRITTEN WARRANTY.
IN NO EVENT  SHALL CONAIR BE LIABLE 
FOR  ANY  SPECIAL,  INCIDENTAL,  OR 
CONSEQUENTIAL DAMAGES FOR BREACH OF 
THIS OR ANY OTHER WARRANTY, EXPRESS 
OR IMPLIED, WHATSOEVER. 
Some provinces do not allow the exclusion 
or limitation of  special,  incidental,  or con-
sequential  damages,  so  the  above  limita-
tion  may  not  apply  to  you. This  warranty 
gives you specific legal rights, and you may 
also  have  other  rights,  which  vary  from  
province to province.
09CN13386
OTHER IMPORTANT NOTES
During  operation,  the  steamer  hose  may 
gurgle. This is a normal result of condensa-
tion collecting inside the hose. Simply lift the 
T-handle  upward  until  the  hose  is  extended 
to its full height. The gurgling will disappear 
when the excess moisture inside the hose has 
had a chance to drain back into the base. 
DECALCIFICATION
If  the  appliance  begins  to  produce  steam 
more slowly than usual, if the steamer stops 
producing steam and then starts again, or if 
the low-water indicator lamp illuminates even 
with  water  container  full,  you  may  need  to 
decalcify your steamer. Decalcification refers 
to removing the calcium deposits which form 
over time on the metal parts of the steamer. 
For  best  performance  from  your  Conair
®
Fabric Steamer, decalcify the unit from time to 
time. The frequency depends upon the hard-
ness of your tap water and how often you use 
the steamer. 
To decalcify, use a solution of 1/3 white vin-
egar  and  2/3  water  in  the  water  container. 
Replace the water container in the unit. Plug 
the unit into electrical outlet. Turn  to  the  on 
position  and  run  until  half  the  amount  has 
steamed  (1 liter). Turn  the  unit  to the  off 
position,  unplug from  electrical outlet,  and 
allow to  sit for  30  minutes. Remove  water 
container. 
Always steam with hose in upright  
position, so any condensation is free  
to flow back into the steamer. 
If you steam with hose not upright, conden-
sation will collect inside the hose. This will 
cause gurgling and some water droplets to 
form near the steam jets on the T-handle. To 
avoid this, frequently lift the steam handle 
upward until the hose is extended to its full 
height. 
TO STEAM DRAPES
Wash and dry drapes as directed according 
to fabric type. Re-hang drapes and steam 
drapes when in place.
CLEANING AND STORING
I.  Turn the On/Off switch to the off position  
  and unplug from the power source.
2. Wait for the steamer to cool completely for  
  at least 30 minutes.
3. Unplug power cord and gently wrap    
  around 
built-in cord wrap. 
4. Remove the steamer hose.
5. Remove the water container from unit,  
  unscrew valve and empty unused contents.  
  Allow to air dry.
6. Remove excess water from the reservoir  
  by 
lifting the unit and pouring into a sink.
7. Replace water container.
8. Store the unit.
Model CTC71C
Convenient to Use 
on Clothes, Drapes  
& Linens!
Instructions 
for Use
For your safety and 
continued enjoyment of this 
product, always read the 
instruction book carefully 
before using.
IB-9196
f
abric steamer
SERVICE CENTRE:
Conair Consumer Products Inc. 
100 Conair Parkway
Woodbridge, ON L4H 0L2
1-800-472-7606
www.conaircanada.ca
Consumer Call Centre E-mail:
Consumer_Canada@Conair.com 
©2009 Conair Consumer Products Inc.
TECHNIQUE DE DÉFROISSAGE
Saisir  la poignée  en T, tenant  la buse  de 
vaporisation  à  l’opposé  de  sa  personne. 
Commencer dans le bas  du tissu,  laissant 
la vapeur monter sur l’intérieur et l’extérieur, 
éliminant les froissements. Passer lentement  
la buse de bas en haut du tissu. Éloigner la 
buse  du  vêtement  et  lisser  le  tissu  avec  la 
main libre. Certains tissus se pressent mieux 
en les vaporisant par  l’intérieur. Les fibres 
peuvent ainsi  mieux se détendre et éliminer 
les froissements.
REMARQUE  :    S’assurer  que  le  tissu  ne 
déteint  pas  en  faisant  un  test  à  un  endroit 
caché.  Étaler  la  literie,  les  serviettes,  les 
mouchoirs et les serviettes de table sur une 
tige ou un porte-serviette.
Les tissus plus épais peuvent nécessiter une 
vaporisation répétée. Répéter au besoin. 
Un peu de pratique permettra de mieux juger 
du travail nécessaire. 
Ne pas laisser la buse toucher directement le 
velours ou la soie.
Toujours vaporiser avec le tube allongé 
pour permettre le retour de condensat 
dans le défroisseur.
Défroisser dans une position abaissée per-
met au condensat de s’accumuler dans le 
boyau, causant un régurgitement et la for-
mation de gouttelettes dans le jet de vapeur. 
Pour éviter cela, soulever régulièrement la 
poignée vers le plafond pour allonger le flex-
ible au maximum.
SOLUTIONS AUX PROBLÈMES
• PROBLÈME - Le défroisseur ne chauffe pas
   CAUSE - Le défroisseur n'est pas branché
   SOLUTION - Brancher le fil dans une prise 
  de courant
• PROBLÈME - Pas de vapeur
   CAUSE - Le niveau d’eau est bas
   SOLUTION - Éteindre le défroisseur et   
  remplir le réservoir d’eau
• PROBLÈME - Des gouttes d’eau sortent par  
  la buse
   CAUSE - Condensation dans le flexible
   SOLUTION - Allonger le flexible et laisser  
  l’eau retourner dans le défroisseur
• PROBLÈME - La buse régurgite
   CAUSE - Condensation dans le flexible
   SOLUTION - Allonger le flexible et laisser  
  l’eau retourner dans le défroisseur
• PROBLÈME - Peu de vapeur
   CAUSE - Défroisseur entartré
   SOLUTION - Détartrer le défroisseur et le  
  réservoir
Remarque : La teneur en minérais dans 
l’eau varie d’un endroit à l’autre. Pour un 
bon fonctionnement, ne jamais ranger le 
défroisseur sans d’abord nettoyer et vider le 
réservoir et le contenant d'eau.
GARANTIE LIMITÉE D’UN AN
Conair réparera ou remplacera (à sa discrétion) 
votre appareil sans frais, si au cours des 12 
mois suivant la date d’achat, il affiche un vice 
de matière ou de fabrication. 
Pour un service au titre de la garantie, renvoyez 
le produit défectueux au service après-vente 
ci-dessous, accompagné du bon de  caisse 
et  de  5,50  $  pour  les  frais  de  poste  et 
d’administration.  En  l’absence  du  bon  de 
caisse, la période de garantie sera de 12 mois 
à compter de la date de manufacture.
TOUTE  GARANTIE,  OBLIGATION  OU 
RESPONSABILITÉ IMPLICITE, Y  COMPRIS, 
MAIS SANS Y ÊTRE  LIMITÉ, LA GARANTIE 
IMPLICITE  DE  QUALITÉ  MARCHANDE  ET 
D’APTITUDE  À  PRODUIRE  UNE  TÂCHE 
PARTICULIÈRE, SERA LIMITÉE À LA PÉRIODE 
DE 12 MOIS DE CETTE GARANTIE ÉCRITE. 
EN  AUCUN  CAS  PEUT-ON  TENIR  CONAIR 
RESPONSABLE  DE  QUELQUE  DOMMAGE 
FORTUIT,  INDIRECT  OU  SPÉCIAL  QUE  CE 
SOIT  POUR  BRIS  DE  CETTE  GARANTIE  OU 
DE TOUTE AUTRE, EXPRESSE OU IMPLICIT
Cette  garantie  vous  confère  des  droits 
partculiers  et  vous  pouvez  également 
bénéficier  d’autres  droits  qui  varient  d’un 
province à l’autre.
09CN13386 
AUTRES REMARQUES IMPORTANTES
Pendant l’usage, le défroisseur peut régurgiter. 
Ceci est le résultat normal de la condensation 
à l’intérieur  du  boyau.  Soulever  la poignée 
en T  jusqu’à  ce  que  le  boyau  soit  étiré. 
Le  régurgitement  cessera dès que  l’excès 
d’humidité dans le boyau aura la chance de 
retourner dans le fond de l’appareil.
DÉTARTRAGE
Si la vapeur prend plus de temps que nor-
malement à se produire, si le défroisseur 
cesse de produire de la vapeur puis se 
remet en marche, il est temps de détartrer 
le défroisseur. Détartrer consiste à éliminer 
les dépôts de calcium qui se forment sur 
les pièces métalliques avec le temps. Pour 
assurer le bon fonctionnement du défrois-
seur Conair®, il faut la détartrer de temps à 
autre. La fréquence dépend de la dureté de 
l’eau du robinet et de la fréquence d’usage.
Pour le détartrer, utiliser une solution de 
1/3 de vinaigre blanc et 2/3 d’eau dans le 
réservoir du défroisseur. Mettre le défrois-
seur en marche et le laisser fonctionner 
jusqu’à ce que la moitié de la solution (1 
litre) soit évaporée. Éteindre le défroisseur, le 
débrancher et le laisser reposer 30 minutes.
Enlever l’eau dans le fond de la cavité en 
soulevant le défroisseur et l’inclinant au-des-
sus de l’évier et en laissant l’eau se vider 
du réservoir intérieur. Répéter autant de 
fois que nécessaire pour obtenir une vapeur 
normale (2 à 3 
fois). Utiliser une 
solution fraîche de 
vinaigre et eau à 
chaque fois. Faire 
un cycle avec de 
l’eau fraîche après 
le détartrage, 
avant d’utiliser 
le défroisseur de 
nouveau.
DÉFROISSER DES RIDEAUX
Laver et sécher les rideaux en suivant les 
directives pour le type de tissu. Suspendre 
les rideaux et les défroisser en place.
NETTOYAGE ET RANGEMENT
I.   Régler l’interrupteur en position d’arrêt et 
  débrancher le fil de la prise de courant. 
2. Attendre au moins 30 minutes pour que le 
  défroisseur refroidisse.
3. Débrancher le fil et l'enrouler lâchement  
  sur l'enrouleur intégré.
4. Déconnecter le flexible.
5.  Enlever le contenant d'eau, dévisser la 
  valve et vider l'eau restante. Laisser 
  sécher à l'air.
6. Enlever l’excédent d’eau dans le réservoir 
  en soulevant l’appareil et le vidangeant 
  dans un drain.
7. Remettre le contenant d'eau.
8. Ranger le défroisseur.
Modèle CTC71C
Pratique sur les 
vêtements, les 
draperies et la lingerie!
Mode 
d'emploi
Pour un usage sûr et 
pratique de ce produit, 
toujours lire le manuel 
d’instructions avant de 
l’utiliser.
IB-9196
défroisseur
SERVICE APRÈS-VENTE :
Conair Consumer Products Inc. 
100 Conair Parkway
Woodbridge, ON L4H 0L2
1-800-472-7606
www.conaircanada.ca
©2009 Conair Consumer Products Inc.
Have a Question? 
Please do not return this 
product to the retailer.
Call Us First! 
Our customer service and 
product experts are ready to 
answer ALL your questions.
Please call our TOLL-FREE  
customer service number at:  
1-800-472-7606
 or visit us online at  
www.conaircanada.ca 
Des questions?  
Veuillez ne pas retourner 
ce produit au détaillant.
Appelez-nous d’abord! 
Notre Service à la clientèle et 
nos experts sont prêts à 
répondre à TOUTES vos  
questions. Veuillez composer
le NUMÉRO SANS FRAIS de 
notre Service à la clientèle : 
1-800-472-7606 
Ou visitez notre site Internet 
au : www.conaircanada.ca 






