User guide
TPBS028-0207
MODELS TB900-4 TB900-6
Performance characteristics
Batch size lb {g} 19.8 {9000} 19.8 {9000}
Maximum throughput rate lb/hr {kg/hr}
*
3500 {1588} 2800 {1270}
Bin capacity - main ingredient ft
3
{liter} 4.4 {124.6} 4.4 {124.6}
Bin capacity - minor ingredient ft
3
{liter} 4.4 {124.6} 2.2 {62.3}
Maximum number of materials 4 6
Number of vertical discharge valves 4 6
Number/(size) of major bin valves 2 - (100 mm) 2 - (100 mm)
Number/(size) of minor bin valves 2 - (60 mm) 4 - (60 mm)
Dimensions inches {mm}
A - Height above mounting plate
†
74.75 {1896} 74,75 {1896}
B - Width 48.5 {1229} 48.5 {1229}
C - Depth 51.0 {1296} 51.0 {1296}
D - Control height 8.25 {209.6} 8.25 {209.6}
E - Control width 9.25 {235.0} 9.25 {235.0}
F - Control depth 4.75 {120.6} 4.75 {120.6}
Weight lbs {kg}
Installed 550 {249} 550 {249}
Shipping 700 {318} 700 {318}
Voltage total amps
115V/1 phase/60 hz 6.3 6.3
230V/1 phase/50 hz 3.2 3.2
Compressed air requirements
Discharge valves 90 psi @ 0.2 ft
3
/min {6 bars @ 0.09
liters/sec}; 1/4 in. NPT fitting
Maximum loader sizes
20 inch loaders - number of loaders 4 2
15 inch loaders - number of loaders NA 2
8 inch loaders - number of loaders NA 2
SPECIFICATION NOTES
*
Maximum throughput rates are based on 35 lb/ft
3
pelletized
material and using all standard valve sizes. Use of reducer
inserts will lower the rate shown.
†
The optional flow control valve will mount inside the chassis in
the space of the manual slide valve. Conair recommends using
the optional flow control valve when mounting the blender on a
stand, surge bin or hopper.
‡ TB900-4 hopper positions three and four are supplied with
12-8 adapters with eight inch cover plates as standard. TB900-6
hopper positions three and six are supplied with 12-8 adapters
and eight inch cover plates as standard.
Specifications may change without notice, consult with a Conair
representative for the most current information.
8 {203}
16 {406}
19-11/16 {500}
19-7/8 {505}
9-27/32
{250}
3-15/16
diameter
{100}
9-15/16 {252}
5-15/16
{151}
1-27/32
{47}
1-15/16
{49}
5-27/32
{148}
MOUNTING INTERFACE
Dimensions
shown in inches
and {mm}.
Top view
Front view
Side view
Control
A
B
C
F
E
D
Position 1
Position 2
‡Position 4
‡Position 3
Position 1
‡Position 4
‡Position 3
Position 2
4 position
6 position
‡Position 5
‡Position 6
NOTE: Side and front view drawings
are model TB900-6.
The bin positions change for a
TB900-4, see the top view.
16 5
4
Mixing chamber access door -
this side of the interface.
Purchase
the optional
material drain chute
that readily installs to
the chassis opening of
the blender for fast
and simple cleanout.
Mounting bolt hole size (8 holes) 9/16 inch {14.0 mm}.
Predrilled 8 x 8 and 16 X 16 mounting pattern as standard.
Drain chute
TrueBlend™ TB900-4
Technical Specifications
and TB900-6
27
Edition: February 2008