Easy Care 5000 Fabric Steamer Model CGS28BA
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially when children are present, basic safety instructions should always be followed, including the following: Polythene bags over product or package may be dangerous. To avoid danger of suffocation, keep this wrapper away from babies and children. This bag is not a toy. DANGER: When the unit is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the unit is switched off.
• This appliance is not intended for commercial use. • Never drop or insert any object into an opening or hose. • Do not use if unit has been dropped or damaged. • Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. • Keep the cord away from heated surfaces. • Never yank the cord to disconnect from the power outlet, instead grasp plug and pull to disconnect. • Do not use this appliance if the supply cord is damaged.
• Before unit is turned on, the hose must be extended, and then place it in the hook. • Do not place the steam nozzle directly onto any surface or on the appliance power cord while it is hot or plugged in. • Use with caution when changing attachments as they may contain hot water or condensation from the nozzle. Attachments should never be placed on the unit when in use or when preheating. Ensure that the attachments are dry or cooled to avoid contact with hot water.
GETTING TO KNOW YOUR STEAMER 360˚ rotating hanger spins for convenient steaming access 30% more steam* with a unique nano-silver ceramic coated nozzle Up to 100min of continuous steam Cool touch handle with easy-grip control Duo pant clip system, specially designed to easily steam trousers & long garments Removable 2.
STEAMER ASSEMBLY The garment steamer comes in several parts: 1. Telescopic pole 2. Extendable telescopic pole 3. One metal rod with pant clip system 4. Two grooved plastic connectors (one is attached to the base of the steamer and the other is attached to the metal rod with pant clip system) 5. One round plastic connector with hook 6. One 360˚ rotatable hanger with pant clip system 7. 2-in-1 lint and bristle brush attachment 8. Press attachment 9.
Assembling the Telescopic Pole, Pant Clip System and 360° Rotatable Hanger Step.1 Loose the existing grooved plastic connector from the base of the steamer (Fig.A) Step.2 Insert telescopic pole, marked ‘1’ (with open hole facing down) into the connector and receptacle in base of the steamer (Fig.B). Slide the pole into the base of the steamer and twist into place, and then push the pole down as far as it can go, until it clicks into place. Screw tighly the grooved connector into place. (Fig.B) Step.
Step.4 Tightly screw the grooved connector.(Fig.C) Step.5 Insert the round plastic connector with hook onto the top of the pole on the garment steamer. (Fig.D) Push the round plastic connector down the pole until it cannot be pushed down any further. Step.6 Take the extendable telescopic pole, marked ‘2’ and unclip the white plastic clip (Fig.E). Extend the pole as far as required and secure desired height by closing the white plastic clip. (Fig.F) (Fig.E) (Fig.
Step.7 Place the extendable telescopic pole (with open hole facing down) into the top of the round plastic connector already on the garment steamer. Align the pole and then lightly push down into place. (Fig.G) (Fig.G) Step.8 Place the rotatable hanger with pant clip system over the top of the pole. NB – The pant clips on the hanger should be at the front of the garment steamer. Hold the pole and then push the hanger down into place. (Fig.H) (Fig.
The telescopic pole, hanger and duo pant clip system should now be in place. You are now ready to attach the hose and nozzle to the steamer.Attaching the Steamer Hose To attach the steamer hose, insert the bottom of the steamer hose into the base of the garment steamer. Twist clockwise to secure in place. 1. 2. 1. Insert 3. 2. Turn 3. Lock Removing the Steamer Hose Ensure that the garment steamer has cooled down. To remove the steamer hose, turn slowly counter clockwise to release. 1. 1.
USING THE PANT CLIP SYSTEM This garment steamer includes a duo pant clip system for holding pants taut for faster and more effective steaming. (Fig.L) The bottom clips can be adjusted by loosening the knob on the metal rod and the height can also be adjusted by simply sliding the metal rod up or down the telescopic pole, depending on the length of the pants. To move the metal rod up or down, simply unscrew and release the grooved connector, then move the metal rod as required. (Fig.
To attach the 2-in-1 lint and bristle brush to the nozzle, simply align the bottom of the attachment with the bottom of the nozzle. Push the top of the attachment forward until it clicks into place. The 2-in1 lint and bristle bush should then be attached to the nozzle and is now ready to use. To remove, simply unclick the top of the attachment and pull away from the nozzle.
WHAT IS THE NANO-SILVER CERAMIC COATING ON THE NOZZLE AND HOW DOES IT WORK? The nozzle on this steamer has a lightweight stainless steel surface that is coated with ceramic and nano-silver. The nano-silver ceramic coating works in two ways: 1. Ceramic coating provides even heat and steam distribution over the entire surface of the nozzle, helping to easily remove wrinkles and reduce hotspots on fabric. 2. Micro particles of nano silver refresh and rejuvenate fabric and remove unpleasant odours.
with the handle and turn upside down. 2. Unscrew the valve and spring assembly cap in the centre of the container. 3. Fill water container by holding the container under a source of cold water. Only use clean water for filling the steamer. In hard water areas, we recommend the use of distilled water. There is no need to fill with warm or hot water, as the steamer heats the water while producing steam. NB - NEVER USE ADDITIVES SUCH AS SALT, PERFUME OR DYE WITH THIS STEAMER.
NB – THIS SETTING IS A VERY POWERFUL, ADVANCED SETTING. TAKE EXTRA CARE WHEN USING THIS STEAM SETTING. This setting provides 80 minutes of continuous steam. Switch the on/off switch on the base of the steamer to the required setting. When using the: I. Normal setting, the LED will illuminate in a light red colour II. Pro-steam setting, the LED will illuminate in a bright red colour. NB - Always check the LED light and on/off switch to ensure you are aware of which steam setting you are using. 5.
1. Grasp the nozzle with the steam jets facing away from you. 2. Begin at the bottom of the garment to allow the steam to rise and remove wrinkles from the inside and outside of the fabric. NB – Some garments are best steamed on the underside of the material. 3. Slowly move the nozzle from the bottom to the top of the garment. 4. Remove the nozzle from the garment and smooth the fabric with your free hand. This will allow the fibres of the fabric to relax and help eliminate wrinkles and creases.
back into the base of the steamer. The gurgling will stop when the excess moisture inside the nozzle and hose has had a chance to flow back into the base of the steamer. If you steam with the hose upside down, condensation will collect inside the hose. This will cause gurgling and some water droplets to form near the steam jets on the handle. To avoid this, frequently lift the steam handle upward until the hose is extended to full height.
over the storage hook e) place the middle round section of the hanger into the clip on the front of the storage hook. Decalcification of Your Steamer If the appliance begins to produce steam more slowly than usual, stops producing steam and then starts again, you may need to decalcify your steamer. Decalcification refers to removing the calcium deposits which can form over time on the metal parts of the steamer.
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Steamer fails to heat Steamer is not plugged in Plug into power outlet and switch product on No steam Water level is low Switch product off and refill water container Water drips from nozzle Condensation in hose Hold the nozzle and hose vertically and allow water to drain back into unit Nozzle gurgles Condensation in hose Hold the nozzle and hose vertically and allow water to drain back into the unit Poor steaming performance 1.
LIMITED ONE YEAR WARRANTY This product is subject to the express warranty given on the warranty card included with the product, as may be amended by reference to and in accordance with the terms of the warranty cards displayed on Conair website www.conairaustralia.com.au To make a warranty claim you must retain your proof of purchase. Further details can be found at www.conairaustralia.com.au and click on ‘customer service’.
