User guide

Operation l 4-7
4
Operation
DRYER MAIN MENU
STAT SETUP DIAG
DRYER SETUP
PROC ALM DISP OTHER
SETUP PROCESS
PROC REGEN OTHER
SETUP REGENERATION
REGEN PID
SETUP REGENERATION
SETUP REGEN HEATER
SCREENS
PID VALUE SCREENS
REGENERATION TEMP
REGEN POWER LIMIT
ACT 350˚F SET 350˚F
LOW 0% HIGH 100%
REGEN TEMP
REGEN CYCLE TIME
RANGE 100˚F - 375˚F
2.0 SEC
REGEN PID DONE
REGEN PROBAND
AUTOTUNE OFF
67F
REGEN INTERGRAL
25
REGEN DERIVATIVE
4
REGEN PID RESET
HEAT
REGEN CALIBRATION
OFFSET 0˚F
SETUP PROCESS
OTHER SCREENS
AUTOSTART TIMER
ENABLED EDIT
DISABLED
MONDAY START TIME
ON 8:00 AM
MONDAY STOP TIME
OFF 8:00 PM
TUESDAY START TIME
ON 8:00 AM
TUESDAY STOP TIME
OFF 8:00 PM
WEDNESDAY START TIME
ON 8:00 AM
WEDNESDAY STOP TIME
OFF 6:00 PM
THURSDAY START TIME
ON 8:00 AM
THURSDAY STOP TIME
OFF 6:00 PM
FRIDAY START TIME
ON 8:00 AM
FRIDAY STOP TIME
OFF 8:00 PM
SATURDAY START TIME
ON 8:00 AM
SATURDAY STOP TIME
OFF 8:00 PM
SUNDAY START TIME
ON 8:00 AM
SUNDAY STOP TIME
OFF 8:00 PM
REGEN CALIBRATION
OFFSET 0˚F
PROCESS DEWPOINT
SAMPLE RATE 150 SEC
PROCESS DEWPOINT
TRIM UP LIMIT
375˚F
PROCESS DEWPOINT
TRIM LOW LIMIT 100F
PROCESS DEWPOINT
GAIN 0.7
PROCESS DEWPOINT
DEAD BAND 1
PROCESS DEWPOINT
CONTROL RESET
REGEN OUTLET TEMP
ACT 280
12
36
37
48 14
14
14
4
29
39
40
47
49
50
51
52
53
54
41
42
43
44
45
46
47
55
56
57
56
57
56
57
56
57
56
57
56
57
56
57
DM T6 TOP
ACT 150˚F
DM T5
ACT 155˚F
57a
57b
DM T4
ACT 158
˚F
DM T3
ACT 160˚F
57c
57d
DM T2
ACT 163
˚F
DM T1 BOTTOM
ACT 165˚F
57e
57f
DM PROCESS SETPOINT
SET 225˚F
DM LO ALARM SELECT
T4 EDIT
57g
57h
DM LO ALARM SETPOINT
SET 150 ˚F
DM LO ALARM OFFSET
SET 10˚F
57i
57j
DM LO ALARM BAND
SET 40˚F
DM LO ALARM DELAY
SET 5 MIN
57k
57l
DM LO ALARM SETPOINT
HIGH LIMIT 170˚F
DM LO ALARM SETPOINT
LOW LIMIT 130˚F
57m
57n
DM TEMP NOT MET
ALARM TIME SET 4 HRS.
DM HI ALARM SELECT
T1 EDIT
57o
57p
DM HI ALARM SETPOINT
SET 150˚F
DM HI ALARM DELAY
SET 5 MIN
57q
57r
When the DM-II monitor option is
purchased these screens will be
displayed.
NOTE: If you have purchased the
DM-II (drying monitor) option
(available only on MDCW 50-100),
see the DM-II Appendix for infor-
mation pertaining to its operation.
✐