User guide

ManualsBrandsComtrol ManualsAccessories communicationES8510-XT

Industrial Managed Switch

7 - 10/100BASE-TX Ethernet Ports

3 - Gigabit RJ45/SFP Combo Ports

User Guide

Summary of content (204 pages)

PAGE 1
Industrial Managed Switch 7 - 10/100BASE-TX Ethernet Ports 3 - Gigabit RJ45/SFP Combo Ports User Guide
PAGE 2
Copyright Notice Comtrol and RocketLinx are trademarks of Comtrol Corporation. Microsoft and Windows are trademarks of Microsoft Corporation. FireFox is a trademark of Mozilla Foundation. PuTTY is a copyright of Simon Tatham. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective owners. Eighth Edition, July 11, 2014 Copyright © 2010 - 2014. Comtrol Corporation. All Rights Reserved.
PAGE 3
Table of Contents Introduction .......................................................................................................................................... 7 Hardware Installation ........................................................................................................................ 9 Connect the Power and Ground................................................................................................................. 9 Connect the Digital Input s and Relay Outputs ....
PAGE 4
Table of Contents Backup and Restore.................................................................................................................................. 57 Backup the Configuration - Local File Method ................................................................................ 58 Restore the Configuration - Local Method........................................................................................ 59 Backup the Configuration - TFTP Server Method ..................................
PAGE 5
Table of Contents Warning........................................................................................................................................................ 110 Fault Relay.............................................................................................................................................. 110 Event Selection .......................................................................................................................................
PAGE 6
Table of Contents ModBus TCP /IP Support ...............................................................................................................193 Overview...................................................................................................................................................... 193 Modbus TCP/IP Function Codes ............................................................................................................ 194 Error Checking ...................................
PAGE 7
Introduction The ES8510 and the ES8510-XT are managed industrial Ethernet switches that are equipped with seven 10/ 100BASE-TX ports and three Combo ports. The three Gigabit Combo ports provide: • Copper RJ45 Ethernet ports (10BASE-T, 100BASE-TX and 1000BASE-TX) • SFP slots (100BASE-FX and 1000BASE-SX/LX) When an SFP port is active and installed on a Combo port, the corresponding Combo RJ45 port is inactivated.
PAGE 8
Introduction 8 - Introduction RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 9
Hardware Installation You can use the following subsections to install the RocketLinx ES8510: • Connect the Power and Ground • Connect the Digital Input s and Relay Outputs on Page 10 • Mount the ES8510 on Page 11 • Connect the Ethernet Ports on Page 12 • Connect SFP Transceivers (Combo Ports 8-10) on Page 13 • LED Descriptions on Page 13 • Panel Layout on Page 14 • Reset Button on Page 14 Connect the Power and Ground You can use the following procedure to connect power and the ground to th
PAGE 10
Hardware Installation b. Tighten the wire-clamp screws to prevent the wires from coming loose. • PW1 and PW2 support power redundancy and reverse polarity protection. • Accepts a positive or negative power source but PW1 and PW2 must apply to the same mode. • If both power inputs are connected, the ES8510 is powered from the highest connected voltage. • The ES8510 can emit an alarm if PW1 or PW2 are no longer receiving power. See the Warning discussion on Page 110 to configure an alarm. 2.
PAGE 11
Hardware Installation Digital output relay contacts are energized (open) for normal operation and close for fault conditions. The digital output relay contacts support up to 1A at 30VDC. Do not apply voltage and current higher than the specifications. 1. Insert the positive and negative wires (12-24 AWG) into V+ and V-. 2. Tighten the wire-clamp screws to prevent the wires from coming loose.
PAGE 12
Hardware Installation Connect the Ethernet Ports You can use the following information to connect standard Ethernet cables between the ES8510 Ethernet ports and the network nodes. • Ports 1-7 are Fast Ethernet (10/100BASE-TX) ports. • Ports 8-10 are RJ45/SFP Combo Gigabit ports that support 10/100/1000BASE-TX, 100BASE-FX, and 1000BASE-X). See Connect SFP Transceivers (Combo Ports 8-10) on Page 13 for information about SFP installation.
PAGE 13
Hardware Installation Connect SFP Transceivers (Combo Ports 8-10) The ES8510 equips three SFP ports combined with RJ45 Gigabit Ethernet ports (Ports 8-10). The SFP ports accept standard mini GBIC SFP transceivers that support 100BASE-FX/ 1000BASE-X. To ensure system reliability, Comtrol recommends using Comtrol certified SFP Transceivers. 1. Plug the SFP transceiver into the SFP fiber transceiver. The SFP cage is 2 x1 design. 2. Connect the transmit channel to the receive channel at each end. 3.
PAGE 14
Hardware Installation Panel Layout The ES8510 provides ten 10/100BASE-TX ports of which three are Combo ports (RJ45/SFP). Combo Port LEDs Reset Button Combo Ports RS-232 Console Port SFP Ports 100BASE-FX 1000BASE-SX/LX 10/100BASE-TX Fast Ethernet Ports Gigabit Ports 10/100/1000BASE-TX Reset Button The ES8510has a reset button that you can use to reboot the ES8510 or reset the configuration to the factory default.
PAGE 15
Using PortVision DX There are several ways to configure network information. Comtrol Technical Support recommends connecting the ES8510 to a PC or laptop running Windows and installing PortVision DX for initial configuration.
PAGE 16
Using PortVision DX PortVision DX Overview PortVision DX automatically detects Comtrol Ethernet attached products physically attached to the local network segment so that you can configure the network address, upload firmware, and manage the following products: • RocketLinx (managed) switches • DeviceMaster family - DeviceMaster PRO - DeviceMaster RTS - DeviceMaster Serial Hub - DeviceMaster 500 • DeviceMaster UP • DeviceMaster LT • IO-Link Master family In addition to identifying Comtrol
PAGE 17
Using PortVision DX Installing PortVision DX During initial configuration, PortVision DX automatically detects and identifies ES8510 switches, if they are in the same network segment. Use the Software and Documentation CD that came with the ES8510 to check for the latest version of PortVision DX or use the link below to download the latest version. 1.
PAGE 18
Using PortVision DX 6. Click Next to configure the shortcuts. 7. Click Install. 8. Depending on the operating system, you may need to click Yes to the Do you want to allow the following program to install software on this computer? query. 9. Click Launch PortVision DX and Finish in the last installation screen. 10. Depending on the operating system, you may need to click Yes to the Do you want to allow the following program to make changes to this computer? query. 11.
PAGE 19
Using PortVision DX Configuring the Network Settings The ES8510 has the following default values when shipped from the factory: • IP address: 192.168.250.250 • Subnet mask: 255.255.0.0 • Gateway address: 192.168.250.1 Use the following procedure to change the default network settings on the ES8510 for your network. 1. If necessary, start PortVision DX using the PortVision DX desktop shortcut or from the Start button, click All Programs > Comtrol > PortVision DX > PortVision DX.
PAGE 20
Using PortVision DX 4. Highlight the ES8510 for which you want to program network information and open the Properties screen using one of these methods. • Double-click the ES8510 in the Device Tree or Device List pane. • Highlight the ES8510 in the Device Tree or Device List pane and click the Properties button. • Right-click the ES8510 in the Device Tree or Device List pane and click Properties in the popup menu • Highlight the ES8510, click the Manage menu and then Properties.
PAGE 21
Using PortVision DX 5. Optionally, rename the ES8510 in the Device Name field for a PortVision DX friendly name. The default name displays as Device and the last three sets of hex numbers from the MAC address. Note: The MAC address and Device Status fields are automatically populated and you cannot change these values. 6. Optionally, enter the serial number, which is on a label on the ES8510. 7. Select DHCP IP or Static IP for the IP Mode. • If you select DHCP IP, go to Step 8.
PAGE 22
Using PortVision DX Checking the Firmware Version Checking your web interface and bootloader versions is easy in PortVision DX. Comtrol recommends loading the latest firmware and bootloader so that you have all of the latest feature enhancements and bug fixes. 1. If the ES8510 is not displayed in PortVision DX, click the Scan button. 2. Select the Comtrol Ethernet attached product type and click the Scan button. 3. Locate the ES8510 in the Device List pane.
PAGE 23
Using PortVision DX Uploading the Latest Firmware or Bootloader You can use the following procedure to upload the latest firmware or bootloader. 1. If you have not done so, download the latest firmware and bootloader using the previous subsection. 2. Right-click the ES8510 in the Device List pane that you want to update, click Advanced --> Upload firmware. 3. Navigate to the location of the firmware files, select the appropriate file, and then click Open. 4. Click Yes to the Upload Firmware message. 5.
PAGE 24
Using PortVision DX Uploading Firmware to Multiple ES8510 Switches You can use this procedure if your ES8510 is connected to the host PC, laptop, or if the ES8510 resides on the local network segment. Note: Technical support does not advise uploading bootloader to multiple ES8510 switches. Remember that uploading firmware reboots the ES8510, which depending on your network connections may cause firmware uploading to fail on another ES8510. 1.
PAGE 25
Using PortVision DX Adding a New Device in PortVision DX You can add a new ES8510 manually, if you do not want to scan the network to locate it or you want to preconfigure an ES8510 before connecting it to the network. Optionally, you can also add unmanaged devices or RocketLinx switches to maintain information about devices on the network. See the PortVision DX help system for additional information about adding unmanaged RocketLinx switches or third party devices or switches.
PAGE 26
Using PortVision DX 6. Enter the IP Address for the ES8510. It is not necessary to enter the Subnet Mask and Default Gateway 7. Click Ok to close the Add New Device window. It may take a few moments to save the ES8510. 8. If necessary, click Refresh for the new RocketLinx to display in the Device Tree or Device List panes. The RocketLinx shows OFF-LINE if it is not connected to the local network or if an incorrect IP address was entered.
PAGE 27
Using PortVision DX Using the LED Tracker RocketLinx managed switches support the LED Tracker feature, which allows you to toggle on/off the LEDs on a specific device so that you can locate the physical unit. Use this procedure to toggle the LED Tracker feature on RocketLinx switches. 1. Right-click the ES8510 in the Device List pane, click Tracker, and then click ON. The ES8510 SYS LED will flash for five seconds. 2.
PAGE 28
Using PortVision DX Customizing PortVision DX You can customize how PortVision DX displays the devices. You can even create sessions tailored for specific audiences. You can also add shortcuts to other applications using Tools > Applications > Customize feature. The following illustrates how you can customize your view. See the PortVision DX Help system for detailed information about modifying the view. For example, the above screen shot illustrates devices layered in folders.
PAGE 29
Using PortVision DX Accessing RocketLinx Documentation from PortVision DX You can use this procedure in PortVision DX to download and open the previously downloaded documents for the RocketLinx. How to Download Documentation Use this procedure to initially download a document or documents. 1. If necessary, open PortVision DX. 2. Click Help > Documentation. 3.
PAGE 30
Using PortVision DX How to Open Previously Downloaded Documents Use the following procedure to access previously downloaded documents in PortVision DX. Note: Optionally, you can browse to the Program Files (x86) > Comtrol > PortVision DX > Docs subdirectory and open the document. 1. If necessary, open PortVision DX > Start/Programs > Comtrol > PortVision DX > PortVision DX or use the desktop shortcut. 2. Click Help > Documentation. 3.
PAGE 31
Configuration Using the Web User Interface The ES8510 provides in-band and out-band configuration methods: • Out-band management means that you configure the ES8510 using the RS-232 console cable and the Command Line Interface (CLI) to access the ES8510 without attaching an admin PC to the network. You can use out-band management if you lose the network connection to the ES8510. The CLI and Telnet are discussed in Configuration Using the Command Line Interface (CLI) on Page 125.
PAGE 32
Configuration Using the Web User Interface Web User Interface The ES8510 web management page was developed with Java. You can use any standard web browser, which is compatible with the Java Runtime to configure and communicate with the ES8510 from anywhere on the network. If you did not program the IP address for your network using PortVision DX (Programming Network Information on Page 20), you need to change your computer IP address to 192.168.250.x (Network Mask: 255.255.0.0).
PAGE 33
Configuration Using the Web User Interface 4. Enter the user name, the password, and click OK. The default user name and password are both admin. The Welcome page of the web management interface then appears. 5. If you have not done so, you can change the ES8510 IP address to meet your network environment. a. Double-click Basic Setting. b. Click IP Configuration. To use static addressing, enter a valid IP add dress, subnet mask and default gateway. To use DHCP, click Enable in the DHCP Client drop list.
PAGE 34
Configuration Using the Web User Interface Secure Web User Interface The ES8510 web user interface also provides secured management through an HTTPS login so that all of the configuration commands are secure. If you did not program the IP address for your network using PortVision DX (Configuring the Network Settings on Page 19), you need to change your computer IP address to 192.168.250.x (Network Mask: 255.255.0.0). The default IP address for the ES8510 is 192.168.250.250. 1.
PAGE 35
Configuration Using the Web User Interface Windows XP and Windows Server 2003 a. Click No when the popup screen appears and requests you to trust the secured HTTPS connection distributed by the ES8510. b. Click Always trust content from this publisher and then Run when requested to run the application (IP address) in the Warning - Security message. Windows Vista - Windows 7 a. Click the Continue button. b. If necessary, click Show all content. c.
PAGE 36
Configuration Using the Web User Interface 4. Enter the user name and the password and click OK. The default user name and password are both admin. The Welcome page of the web management interface then appears. 5. If you have not done so, you can change the ES8510 IP address to meet your network environment. a. Double-click Basic Setting. b. Click IP Configuration. c. - To use static addressing, enter a valid IP address, subnet mask and default gateway.
PAGE 37
Configuration Using the Web User Interface Feature Overview The following table provides detailed information about ES8510 features and provides the location of the configuration information in the web user interface. Type 802.1x Port-Based Network Access Control Configuration Category 802.
PAGE 38
Configuration Using the Web User Interface Type CoS-Queuing Mapping Category CoS-Queue Mapping on Page 96 Details • CoS 0 through 7 • Queue 0 through 3 • Queue 3 highest priority • DHCP Server Configuration DHCP Server Configuration on Page 52 DHCP Server Configuration DHCP Leased Entries on Page 54 DHCP Relay Agent on Page 55 DSCP-Queuing Mapping Event Selection DSCP-Queue Mapping on Page 97 Event Selection on Page 112 - Excluded Addresses and Manual Binding Port and IP Address Option 82
PAGE 39
Configuration Using the Web User Interface Type GVRP Configuration IGMP Query IGMP Snooping Category GVRP Configuration on Page 90 IGMP Query on Page 100 IGMP Snooping on Page 99 Details • 2K Entries • Enable/Disable GVRP Protocol • State - Enable/Disable • Join Timer • Leave Timer • Leave All Timer • Version - Version 1, Version 2, or Disable • Query Intervals • Query Maximum Response Time • Enable/Disable • VID • Port by Port IGMP Snooping Table - IP Address - VID IP Confi
PAGE 40
Configuration Using the Web User Interface Type MSTP Information Category Details • Instance ID • Root Information - MSTP Information on Page 80 • Root Address Root Priority Root Port Root Path Cost Maximum Age Hello Time Forward Delay Port Information - Role Port State Path Cost Port Priority Link Type Edge Port Instance ID MSTP Port Configuration Ping Utility Port Control MSTP Port Configuration on Page 79 Ping Utility on Page 121 Port Control on Page 65 Port Mirror Mode Port Mirroring
PAGE 41
Configuration Using the Web User Interface Type Category Details Port by Port Port Statistics Port Status Port Statistics on Page 117 Port Status on Page 67 • Type • Link • State • Rx and Tx Good • Rx and Tx Bad • Rx Abort • Collision • Port Type • Link - Up/Down • State - Enable/Disable • Speed/Duplex • Flow Control • SFP Vendor, Wavelength, and Distance • SFP DDM - Temperature, Tx Power, and Rx Power Aggregation Settings • Port Trunk Group ID - Trunk 1-5 Aggregation
PAGE 42
Configuration Using the Web User Interface Type Category Details Queue scheduling QoS Setting Rate Control Redundant Ring Redundant Ring Information Reset/Reboot SNMP Configuration 42 - Feature Overview QoS Setting on Page 95 Rate Control on Page 68 • Use 8.4.2.
PAGE 43
Configuration Using the Web User Interface Type SNMP Traps Category SNMP Traps on Page 103 Details • Enable/Disable • Trap Server - Server IP Address, Community, and Version (V1 or V2c) • Trap Server Profile - Displays Server IP, Community, and Version SNMP V3 SNMP V3 Profile SNMP V3 Profile on Page 102 • User Name • Security Level • Authentication Level • Authentication Password • DES Password SNMP V3 Users - Displays Profile Information STP Configuration STP Information STP Conf
PAGE 44
Configuration Using the Web User Interface Type SYSLOG Mode System Event Logs Time Setting Topology Discovery Unknown Multicast Upgrade Firmware VLAN Configuration VLAN Port Configuration VLAN Table Warning - SMTP Configuration 44 - Feature Overview Category SysLog Configuration on Page 113 Event Log on Page 119 Time Setting on Page 49 Topology Discovery (LLDP) on Page 120 Unknown Multicast on Page 100 Firmware Upgrade on Page 61 VLAN Configuration on Page 87 VLAN Port Configuration on Pag
PAGE 45
Configuration Using the Web Interface Basic Settings The Basic Setting group allows you the ability to configure switch information, IP address, User name/ Password of the system. It also allows you to do firmware upgrade, backup and restore configuration, reload factory default, and reboot the system.
PAGE 46
Configuration Using the Web Interface Switch Setting Page (Continued) Device MAC Displays a unique hardware address (MAC address) assigned at the factory. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 123), if you want to maintain these settings if the ES8510 is powered off. Admin Password You can change the user name and the password here to enhance security. Admin Password Page Administrator Name You can enter a new user name here. The default name is admin.
PAGE 47
Configuration Using the Web Interface IP Configuration This function allows you to configure the ES8510’s IP address settings. IP Configuration Page DHCP Client You can select to Enable or Disable the DHCP Client function. When the DHCP Client function is enabled, an IP address is assigned to the switch from the network’s DHCP server. In this mode, the default IP address is replaced by the one assigned by DHCP server. If DHCP Client is disabled, then the IP address that you specified is used.
PAGE 48
Configuration Using the Web Interface IP Configuration Page (Continued) You can assign the subnet mask for the IP address here. If the DHCP Client function is enabled, you do not need to assign the subnet mask. The default Subnet Mask is 255.255.255.0. Subnet Mask Default Gateway Note: In the CLI, the enabled bit of the subnet mask is used to represent the number displayed in the web management interface. For example, 8 represents: 255.0.0.0,16 represents: 255.255.0.0, 24 represents: 255.255.255.0.
PAGE 49
Configuration Using the Web Interface Time Setting Time Setting allows you to set the time manually or through a Network Time Protocol (NTP) server. NTP is used to synchronize computer clocks on the internet. You can configure NTP settings here to synchronize the clocks of several switches on the network. The ES8510 also provides Daylight Saving functionality. Time Setting Page Manual Setting: Click Manual Setting to change time as needed.
PAGE 50
Configuration Using the Web Interface Switch(config)# clock timezone 01 (GMT-12:00) Eniwetok, Kwajalein 02 (GMT-11:00) Midway Island, Samoa 03 (GMT-10:00) Hawaii 04 (GMT-09:00) Alaska 05 (GMT-08:00) Pacific Time (US & Canada), Tijuana 06 (GMT-07:00) Arizona 07 (GMT-07:00) Mountain Time (US & Canada) 08 (GMT-06:00) Central America 09 (GMT-06:00) Central Time (US & Canada) 10 (GMT-06:00) Mexico City 11 (GMT-06:00) Saskatchewan 12 (GMT-05:00) Bogota, Lima, Quito 13 (GMT-05:00) Eastern Time (US & Canada) 14 (G
PAGE 51
Configuration Using the Web Interface 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 (GMT+05:45) (GMT+06:00) (GMT+06:00) (GMT+06:00) (GMT+06:30) (GMT+07:00) (GMT+07:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+09:00) (GMT+09:00) (GMT+09:00) (GMT+09:30) (GMT+09:30) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+11:00) (GMT+12:00) (GMT+12:00) (GMT+13:00) Kathmandu Almaty, Novosibirsk Astana, Dhaka Sri Jayawardenepura Rangoon Bangkok,
PAGE 52
Configuration Using the Web Interface DHCP Server Configuration Use this page to configure DHCP server services. DHCP Server Configuration Page DHCP Server You can select to Enable or Disable the DHCP Server function. The ES8510 assigns a new IP address to link partners. DHCP Server Configuration Network 52 - DHCP Server Configuration Enter the IPv4 address for the DHCP server. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 53
Configuration Using the Web Interface DHCP Server Configuration Page (Continued) Subnet Mask Enter the subnet mask for the DHCP server. Default Gateway Enter the IP gateway address for the DHCP server. Lease Time Enter the Lease Time in seconds for the client. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 123), if you want to maintain these settings if the ES8510 is powered off.
PAGE 54
Configuration Using the Web Interface DHCP Leased Entries The ES8510 provides an assigned IP address. DHCP Leased Entries Page Index Index of DHCP leased entries. Binding Manual or auto binding IP addresses and MAC addresses. IP Address The IP address of the leased entry. MAC Address The MAC Address of the leased entry. Lease Time(s) The lease time of the leased entry (in seconds). Reload Click to reload DHCP leased entries.
PAGE 55
Configuration Using the Web Interface DHCP Relay Agent This subsection discusses the DHCP Relay Agent page. DHCP Relay Agent Page Relay Agent You can select to Enable or Disable the DHCP Relay Agent function. The ES8510 assigns a new IP address to link partners. Relay Policy Relay policy drop Drops the option 82 field and do not add any option 82 field. Relay policy keep Keeps the original option 82 field and forwards to server.
PAGE 56
Configuration Using the Web Interface DHCP Relay Agent Page (Continued) DHCP Option82 Relay Agent Default: Default value of the Circuit-ID. Port: Port of the switch. Circuit ID Circuit ID: The Circuit ID includes information specific to which circuit the request came in on. It is an identifier that is specific to the relay agent, so the type of circuit varies depending on the relay agent. Default: Default value of the Remote-ID. Remote-ID IP Address: IP Address of the switch.
PAGE 57
Configuration Using the Web Interface Backup and Restore You can use the Backup option to save the current configuration saved in the ES8510 flash to a PC/laptop or a TFTP server. This allows you to use the Restore option to restore a configuration file back to the ES8510 or load the same settings to another ES8510. Before you can restore a configuration file, you must save the backup configuration file in the PC or TFTP server. The ES8510 then downloads this file back into the flash.
PAGE 58
Configuration Using the Web Interface Backup the Configuration - Local File Method Use the following procedure to use the Local File method to create a configuration file. Note: If you have a Windows operating system above Windows XP, you can use the TFTP Server method, the CLI, PortVision DX, or apply exclusions for Java for the Windows firewall to backup or restore configuration files.
PAGE 59
Configuration Using the Web Interface 4. Click the Folder icon, browse to the location that you want to store the backup configuration file, enter a file name, and click Open. Note: You cannot use spaces in the path to the target file. 5. Click the Backup button and then click Ok when the Success Message appears. Restore the Configuration - Local Method You can use Local File method to restore with a Windows XP system.
PAGE 60
Configuration Using the Web Interface Backup the Configuration - TFTP Server Method If you do not have a TFTP server, you can download one from Comtrol using the Start the TFTP Server subsection. Start the TFTP Server Use this procedure to download either the 32-bit or the 64-bit version from Comtrol. 1. If necessary, download the appropriate .zip file for your operating system from: ftp://ftp.comtrol.com/ contribs/free_3rd_party_utils/tftp_server/ to your system and unzip the file. 2.
PAGE 61
Configuration Using the Web Interface Restore the Configuration - TFTP Server Method To restore a configuration file, you must open a TFTP server. If necessary, use Start the TFTP Server on Page 60. The backup file must be located in the same directory that the TFTP server resides for this procedure to work. 1. Open the web user interface for the ES8510, open the Backup and Restore page under Basic Settings. 2.
PAGE 62
Configuration Using the Web Interface Upgrading Firmware (Local File) You can use this procedure to upgrade the web interface firmware (not Bootloader). Note: You can also use PortVision DX to upload the web interface firmware. You must use PortVision DX or the CLI to upload the Bootloader firmware. 1. Windows operating systems after Windows XP: you must add Java to your Windows firewall exclusion list. See Step 1 on Page 58 if you need to add Java exclusions for the Windows firewall. 2.
PAGE 63
Configuration Using the Web Interface 4. Select TFTP Server in the Firmware Upgrade drop list. 5. Enter the IP address of the TFTP server, enter the firmware file name, and click the Upgrade button. 6. Click Yes to the Confirm Dialog message. 7. Click Ok to the Warning Message. 8. Click Ok to close the Success Message. Note: After the firmware has successfully uploaded, you should close and re-open the browser to clear the Java Virtual Machine cache.
PAGE 64
Configuration Using the Web Interface System Reboot System Reboot allows you to reboot the device. Most feature changes require a switch reboot to take affect. Note: Before rebooting, remember to click Save to save your settings. Otherwise, the settings you are lost when the ES8510 is powered off. 1. Click the Reboot button to reboot your ES8510. 2. Click Yes. The switch reboots immediately. 3. Click Ok. 64 - System Reboot RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 65
Configuration Using the Web Interface Port Configuration The Port Configuration group allows you to enable/disable port state, or configure port auto-negotiation, speed, duplex, flow control, port aggregation settings (port trunking), and rate limit control. It also allows you to view port status and aggregation information.
PAGE 66
Configuration Using the Web Interface Port Configuration Page State You can enable or disable the state of this port. Once you click Disable, the port stops to link to the other end and stops to forward any traffic. The default setting is Enable which means all the ports are workable when you receive the ES8510. You can configure port speed and duplex mode of each port.
PAGE 67
Configuration Using the Web Interface Port Status The Port Status page displays the current port status, including Small Form Factory (SFP) fiber transceiver with Digital Diagnostic Monitoring (DDM) function that provides real time information of SFP transceiver and allows you to diagnostic the optical fiber signal received and launched.
PAGE 68
Configuration Using the Web Interface Rate Control Rate limiting is a form of flow control used to enforce a strict bandwidth limit at a port. You can program separate transmit (Egress Rule) and receive (Ingress Rule) rate limits at each port, and even apply the limit to certain packet types as described below. Rate Control Page You can select the packet type that you want to filter.
PAGE 69
Configuration Using the Web Interface Port Trunking Port Trunking allows you to group multiple Ethernet ports in parallel to increase link bandwidth. The aggregated ports can be viewed as a physical port that has a bandwidth equal to the combined bandwidth of each trunked port.The member ports of the same trunk group can balance the loading and backup for each other. The Port Trunking feature is usually used when you need higher bandwidth for the network backbone.
PAGE 70
Configuration Using the Web Interface Aggregation Status The Port Trunk - Aggregation Information page shows the status of port aggregation. Once the aggregation ports are negotiated, you see the following status. Aggregation Status Page Group ID Displays Trunk 1 to Trunk 5 set up. Type The Type is Static or LACP. Static means that LACP is disabled and configured statically by the Administrator. Aggregated When LACP links, you can see the member ports in the Aggregated column.
PAGE 71
Configuration Using the Web Interface Network Redundancy It is critical for industrial applications that the network remains running at all times. The ES8510 supports: • Standard Rapid Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) The ES8510 supports RSTP versions IEEE 802.1D-2004, IEEE 802.1D-1998 STP, and IEEE 802.1w RSTP. • Multiple Spanning Tree Protocol (MSTP) MSTP implements IEEE 802.
PAGE 72
Configuration Using the Web Interface STP Configuration This page allows you to select the STP mode and configure the global STP/RSTP bridge configuration. Spanning Tree Protocol (STP; IEEE 802.1D) provides a loop-free topology for any LAN or bridged network. Rapid Spanning Tree Protocol (RSTP; IEEE 802.1w) is an evolution of the Spanning Tree Protocol (STP), and was introduced with the IEEE 802.1w standard, and provides faster spanning tree convergence after a topology change. In most cases, IEEE 802.
PAGE 73
Configuration Using the Web Interface STP Port Configuration This page allows you to configure the port parameter after you have enabled STP, RSTP, or MSTP. STP Port Configuration Page You can enable/disable STP/RSTP/MSTP on a port by port basis. STP State You can disable the STP state when connecting a device in order to avoid STP waiting periods. Path Cost The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000.
PAGE 74
Configuration Using the Web Interface STP Information The STP Information page allows you to see the ES8510 root information and port status. STP Information Page Root Information Root Address Root bridge address, which is the bridge with the smallest (lowest) bridge ID. Root Priority Root bridge priority, the bridge with the lowest value has the highest priority and is selected as the root. Root Port Root port of this bridge. Root Path Cost Root path cost.
PAGE 75
Configuration Using the Web Interface STP Information Page (Continued) Port Information Port Role Descriptive information about the STP/RSTP switch port role. Role: Root, Designated, Alternate, Backup, Disabled, Unknown. Port State Descriptive information about the STP/RSTP switch port state. State: Blocking, Listening, Learning, Forwarding, Disabled, Unknown. Path Cost The cost of the path to the other bridge from this transmitting bridge at the specified port. Path cost range is 1 through 200000000.
PAGE 76
Configuration Using the Web Interface MSTP Configuration Multiple Spanning Tree Protocol (MSTP) is a direct extension of RSTP. It can provide an independent spanning tree for different VLANs. It simplifies network management, creates a faster convergence than RSTP by limiting the size of each region, and prevents VLAN members from being segmented from the rest of the group (as sometimes occurs with IEEE 802.1D STP). While using MSTP, there are some new concepts of network architecture.
PAGE 77
Configuration Using the Web Interface This is the MSTP Configuration page. MSTP Configuration Page MST Region Configuration Region Name A name used to identify the MST Region. Revision A value used to identify the MST Region. Apply Click the Apply button to apply the MST Region Configuration. New MST Instance Instance ID A value used to identify the MST instance, valid value are 1 through 15.
PAGE 78
Configuration Using the Web Interface MSTP Configuration Page (Continued) Current MST Instance Configuration Instance ID A value used to identify the MST instance. Instance 0 (CIST, Common Internal Spanning Tree) is a special instance of spanning-tree known as IST or Internal Spanning Tree (=MSTI00). VLAN Group Provide a VLAN group to map this MST instance. Use the VLAN number, for example: 10. You can set a range, for example: 1-10) or set specific VLANs, for example: 2,4,6,4-7.
PAGE 79
Configuration Using the Web Interface MSTP Port Configuration This page allows you to configure the port settings. Choose the Instance ID that you want to configure. MSTP Port Configuration Page Instance ID Select an Instance ID to display and modify MSTP instance setting. Port Configuration Path Cost The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000.
PAGE 80
Configuration Using the Web Interface MSTP Information This page allows you to see the current MSTP information. Choose the Instance ID first. If the instance is not added, the information remains blank. 80 - MSTP Information RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 81
Configuration Using the Web Interface MSTP Information Page Instance ID Select an instance ID to display MSTP instance information. Instance 0 (CIST, Common Internal Spanning Tree) is a special instance of spanning-tree known as IST or Internal Spanning Tree (=MSTI00). Root Information Root Address Root bridge address, which is the bridge with the smallest (lowest) bridge ID. Root Priority Root bridge priority, the bridge with the lowest value has the highest priority and is selected as the root.
PAGE 82
Configuration Using the Web Interface Redundant Ring The most common industrial network redundancy is to form a ring or loop. Typically, managed switches are connected in series and the last switch is connected back to the first one. In such connection, you can implement Redundant Ring technology. Redundant Ring Page New Ring (Ring ID/Name) To create a Redundant Ring enter the Ring ID, which has range from 0 to 31.
PAGE 83
Configuration Using the Web Interface Redundant Ring Page (Continued) Rapid Dual Homing Rapid Dual Homing is an important feature of Rapid Super Ring redundancy technology. When you want to connect multiple RSR or form redundant topology with other vendors, RDH allows you to have a maximum of seven multiple links for redundancy without any problem. In RDH, you do not need to configure a specific port to connect to other protocol.
PAGE 84
Configuration Using the Web Interface Loop Protection Loop protection prevents broadcast loops in Layer 2 switching configurations. Loop Protection Page Transmit Interval Port Loop Protection Status Apply Enable/Disable All Reload 84 - Loop Protection Loop protection mechanism detection packet transmitting interval 1 ~ 10 seconds (default is 1). The port ID. Enable/Disable loop protection mechanism on port. The status of loop protection. Click Apply to apply the settings.
PAGE 85
Configuration Using the Web Interface VLAN A Virtual LAN (VLAN) is a logical grouping of nodes for the purpose of limiting a broadcast domain to specific members of a group without physically grouping the members. The VLAN allows you to isolate network traffic so that only members of the VLAN could receive traffic from the same VLAN members.
PAGE 86
Configuration Using the Web Interface VLAN Port Configuration The VLAN Port Configuration page allows you to configure VLAN port parameters on a specific port. These parameters include the port VLAN ID (PVID), Tunnel Mode, Accept Frame Type and Ingress Filtering VLAN Port Configuration Page PVID Enter the port VLAN ID (PVID). The PVID allows the switches to identify which port belongs to which VLAN. To keep things simple, it is recommended that PVID is equivalent to VLAN IDs.
PAGE 87
Configuration Using the Web Interface VLAN Port Configuration Page (Continued) Ingress filtering instructs the VLAN engine to filter out undesired traffic on a port. • When you Enable Ingress Filtering, the port checks whether the incoming frames belong to the VLAN they claimed or not. The port then determines if the frames can be processed or not.
PAGE 88
Configuration Using the Web Interface VLAN Configuration Page The management VLAN ID is the VLAN ID of the CPU interface so that only member Management VLAN ports of the management VLAN can ping and access the switch. The default management VLAN ID is 1. ID Click Apply after you enter the VLAN ID. You can assign a VLAN ID and VLAN Name for the new static VLAN. Static VLAN • VLAN ID: This is used by the switch to identify different VLANs. A valid VLAN ID is between 1 and 4,094, 1 is the default VLAN.
PAGE 89
Configuration Using the Web Interface This figure displays how to configure the Egress rule of the ports. Use the following steps to configure Egress rules: 1. Select the VLAN ID. The entry of the selected VLAN turns to light blue. 2. Assign Egress rule of the ports to U or T. 3. Press Apply to apply the setting. If you want to remove one VLAN, select the VLAN entry and then click the Remove button. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 90
Configuration Using the Web Interface GVRP Configuration GARP VLAN Registration Protocol (GVRP) allows you to set-up VLANs automatically rather than manual configuration on every port on every switch in the network. GVRP conforms to the IEEE 802.1Q specification. This defines a method of tagging frames with VLAN configuration data that allows network devices to dynamically exchange VLAN configuration information with other devices.
PAGE 91
Configuration Using the Web Interface VLAN Table This table displays the current settings of your VLAN table, including VLAN ID, Name, Status, and Egress rule of the ports. VLAN Table Page VLAN ID The ID of the VLAN. Name The name of the VLAN. Static means that this is a manually configured static VLAN. Unused means this VLAN is created by web user interface/CLI and has no member ports and the VLAN is not workable yet. Dynamic means this VLAN was learnt by GVRP. Status • -- No VLAN setting.
PAGE 92
Configuration Using the Web Interface Private VLAN A private VLAN helps to resolve the primary VLAN ID shortage, client ports’ isolation and network security issues. The private VLAN features provides primary and secondary VLANs within a single switch. Primary VLAN: The uplink port is usually a member of the primary VLAN. A primary VLAN contains promiscuous ports that can communicate with Secondary VLANs. Secondary VLAN: The client ports are usually defined within secondary VLAN.
PAGE 93
Configuration Using the Web Interface Private VLAN Configuration Page (Continued) Private VLAN Type • None: The VLAN is not included in private VLAN. • Primary: A primary VLAN contains promiscuous ports that can communicate with the secondary VLANs. • Isolated: The member ports of the VLAN are isolated. • Community: The member ports of the VLAN can communicate with each other. Click Apply to apply the settings.
PAGE 94
Configuration Using the Web Interface For example: 1. VLAN Create: VLANs 2-5 are created in the VLAN Configuration page. 2. Private VLAN Type: VLANs 2-5 has their own Private VLAN Type configured in the Private VLAN Configuration page. VLAN 2 belongs to the Primary VLAN. VLANs 3-5 belong to the secondary VLAN (Isolated or Community). 3. Private VLAN Association: Associate VLANs 3-5 to VLAN 2 in the Private VLAN Association first. 4.
PAGE 95
Configuration Using the Web Interface Traffic Prioritization Quality of Service (QoS) provides a traffic prioritization mechanism which allows you to deliver better service to certain flows. QoS can also help to alleviate congestion problems and ensure high-priority traffic is delivered first. This section allows you to configure Traffic Prioritization settings for each port with regard to setting priorities.
PAGE 96
Configuration Using the Web Interface QoS Setting Page (Continued) Port Setting CoS The CoS column indicates that the default port priority value for untagged or prioritytagged frames. When the ES8510 receives the frames, the ES8510 attaches the value to the CoS field of the incoming VLAN-tagged packets. You can enable 0,1,2,3,4,5,6 or 7 to the port. Trust Mode indicates the Queue Mapping types that you can select.
PAGE 97
Configuration Using the Web Interface DSCP-Queue Mapping Use this page to change DSCP values to Physical Queue mapping table. Since the switch fabric of the ES8510 only supports four queues. Lowest, Low, Middle and High users should therefore assign how to map DSCP values to the level of the physical queue. You should therefore assign how to map DSCP value to the level of the queue. You can change the mapping table to follow the upper layer 3 switch or routers’ DSCP setting.
PAGE 98
Configuration Using the Web Interface Multicast Filtering For multicast filtering, the ES8510 uses IGMP (Internet Group Management Protocol) Snooping technology. IGMP is an internet protocol that provides a way for internet device to report its multicast group membership to adjacent routers. Multicasting allows one computer on the internet to send data to a multitude of other computers that have identified themselves as being interested in receiving the originating computer’s data.
PAGE 99
Configuration Using the Web Interface IGMP Snooping Use this page to enable the IGMP Snooping feature, assign IGMP Snooping for specific VLANs, and view the IGMP Snooping table from a dynamic learnt or static that you provide. IGMP Snooping Page You can select Enable or Disable. After enabling IGMP Snooping, you can then enable IGMP Snooping for specific VLAN. IGMP Snooping You can Enable IGMP Snooping for some VLANs so that some of the VLANs support IGMP Snooping and others do not.
PAGE 100
Configuration Using the Web Interface IGMP Query Use this page to configure the IGMP Query feature. Since the ES8510 can only be configured by member ports of the management VLAN, the IGMP Query can only be enabled on the management VLAN. If you want to run IGMP Snooping feature in several VLANs, first check to see whether each VLAN has its own IGMP Querier. The IGMP querier periodically sends query packets to all end-stations on the LANs or VLANs that are connected to it.
PAGE 101
Configuration Using the Web Interface SNMP Simple Network Management Protocol (SNMP) is a protocol to exchange management information between network devices. SNMP is a member of the TCP/IP protocol suite. The ES8510 supports SNMP v1 and v2c and v3. An SNMP managed network consists of two main components: agents and a manager. An agent is a management software module that resides in a managed switch. An agent translates the local management information from the managed device into a SNMP compatible format.
PAGE 102
Configuration Using the Web Interface SNMP V3 Profile SNMP v3 can provide more security functions when you perform remote management through SNMP protocol. It delivers SNMP information to the administrator with user authentication; all of data between the ES8510 and the administrator are encrypted to ensure secure communication. SNMP V3 Profile Page User Name SNMP v3 user name. Security Level Select the following levels of security: None, Authentication, and Authentication and Privacy.
PAGE 103
Configuration Using the Web Interface SNMP Traps SNMP Trap is the notification feature defined by SNMP protocol. All the SNMP management applications can understand such trap information. So you do not need to install new applications to read the notification information. SNMP Trap Page SNMP Trap Click Enable or Disable SNMP trap functionality. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 123), if you want to maintain these settings if the ES8510 is powered off.
PAGE 104
Configuration Using the Web Interface Security The ES8510 provides several security features for you to secure your connection. The following pages are included in this group: • Port Security on Page 104 • IP Security on Page 105 • 802.1x Configuration on Page 106 • 802.1x Port Configuration on Page 107 • 802.1x Port Status on Page 109 Optionally, you can use the CLI for configuration, see Security (CLI) on Page 170.
PAGE 105
Configuration Using the Web Interface IP Security Use the Security IP page to set up specific IP addresses to grant authorization for management access to this ES8510 through a web browser or Telnet. IP Security Page IP Security Select Enable and Apply to enable the IP security function. You can assign specific IP addresses and then click Add. Only these IP addresses can access and manage ES8510 Add Security IP through a web browser or Telnet. The maximum security IP is 10.
PAGE 106
Configuration Using the Web Interface 802.1x Configuration IEEE 802.1x is the protocol that performs authentication to obtain access to IEEE 802 LANs. It is port-base network access control. With the function, the ES8510 could control which connection is available or not. IEEE 802.1x Page System Auth Control Enable or Disable the IEEE 802.1x authentication. Authentication Method RADIUS is an authentication server that provides a key for authentication.
PAGE 107
Configuration Using the Web Interface IEEE 802.1x Page (Continued) Shows the account information, select Remove to remove a selected account. Local RADIUS User List • User name: The user name of the local RADIUS user. • Password: The password of the local RADIUS user. • VID: The VLAN ID (VID) of the local RADIUS user. 802.
PAGE 108
Configuration Using the Web Interface 802.1x Port Configuration Page Port control Force Authorized means that this port is authorized; the data is free to move in/out. Force unauthorized is just the opposite, the port is blocked. To control this port with a RADIUS server, select Auto for port control. Reauthentication If this field is enabled, the ES8510 requests the client to re-authenticate. The default time interval is 3600 seconds.
PAGE 109
Configuration Using the Web Interface 802.1x Port Status Use the 802.1x Port Status page to observe the port status for Port Control Status, Authorize Status, Authorized Supplicant, and Oper Control Direction for each port. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev. H 802.
PAGE 110
Configuration Using the Web Interface Warning The ES8510 provides several types of warning features for you to remotely monitor the status of the attached devices or changes in your network. The features include Fault Relay, System Log and SMTP Email Alert.
PAGE 111
Configuration Using the Web Interface Off Period (Sec): Type the period time to turn off relay output. The valid range is from 0 to 4,294,967,295 seconds. Event Type: Power Failure Power ID: Select Power 1 or Power 2. When the power is shut down or broken for the selected input the system shorts the relay out and light the DO LED. Event Type: Link Failure Link: Select the port ID you want to monitor. How to configure: Select the check box of the Ethernet ports you want to monitor.
PAGE 112
Configuration Using the Web Interface Event Selection Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of specific ports. System Event Warning is sent when…. Device Cold Start Power is cut off and then reconnected. Device Warm Start Reboot the device by CLI or web user interface.
PAGE 113
Configuration Using the Web Interface System Event Warning Event is sent when…. The information read from the DDM SFP transceiver is over temperature or out the range of TX/RX power. SFP DDM Failure Port Event Warning is sent when….. Link-Up The port is connected to another device. Link-Down The port is disconnected. For example, the cable is pulled out or the opposing devices is down. Both The link status changed. Click Apply to apply the settings.
PAGE 114
Configuration Using the Web Interface SMTP Configuration The ES8510 supports an email alert feature. The ES8510 sends the events that have occurred to a remote email server. The email warning conforms to the SMTP standard. The E-mail Alert page allows you to assign the SMTP Server IP, Sender E-mail, and Receiver E-mail. If the SMTP server requests authentication, you can set up the user name and password. SMTP Configuration Page SMTP Server IP Address Enter the IP address of the email server.
PAGE 115
Configuration Using the Web Interface Monitor and Diag The ES8510 provides several web user interface pages for you to monitor the status of the switch or diagnostics when encountering problems related to the ES8510. The features include MAC Address Table, Port Statistics, Port Mirror, Event Log, and Ping.
PAGE 116
Configuration Using the Web Interface MAC Address Table Page Each switch fabric has a size limit to write the learnt MAC address. To save more entries for a new MAC address, the switch fabric ages out a non-used MAC address entry per the Aging Time timeout. Aging Time (Sec) This value determines the interval that an automatically learnt MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged.
PAGE 117
Configuration Using the Web Interface Port Statistics Use this page to view operation statistics for each port. The statistics that can be viewed include Link Type, Link State, Rx Good, Rx Bad, Rx Abort, Tx Good, Tx Bad and Collisions. Note: If you see an increase of Bad, Abort or Collision counts, that may mean the network cable is not properly connected or the network performance of the port is poor.
PAGE 118
Configuration Using the Web Interface Port Mirroring Port mirroring (also called port spanning) is a tool that allows you to mirror the traffic from one or more ports onto another port, without disrupting the flow of traffic on the original port. Any traffic that goes into or out of the Source Ports is duplicated at the Destination Ports. This traffic can then be analyzed at the Destination Port using a monitoring device or application.
PAGE 119
Configuration Using the Web Interface Event Log The System Log feature was introduced in SysLog Configuration on Page 113. When System Log Local mode is selected, the ES8510 records events that occurred in the local log table. This page shows the log table. The entry includes the index, occurred data and time, and content of the events. Click Clear to clear the entries. Click Reload to refresh the table. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 120
Configuration Using the Web Interface Topology Discovery (LLDP) The ES8510 supports topology discovery or LLDP (IEEE 802.1AB Link Layer Discovery Protocol) functionality that can help to discovery multi-vendor’s network devices on the same segment by a network monitoring system (NMS) that supports LLDP functionality. With LLDP functionality, NMS can easily maintain the topology map, display port ID, port description, system description, and VLAN ID.
PAGE 121
Configuration Using the Web Interface Ping Utility This page provides a Ping Utility to ping a remote device and check whether the device is alive or not. Type the Target IP address of the target device and click Start to start the ping. After few seconds, you can see the result in the Result field. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 122
Configuration Using the Web Interface Device Front Panel The Device Front Panel allows you to see the LED status of the ES8510. LED Name Power 1 Power 2 LED On/Link Up LED Off/Link Down Green Black: No power DO1 (Digital Output) DO2 (Digital Output) Green: DO activated Black: DO not activated DI1 (Digital Input) DI2 (Digital Input) Green: DI activated Black: DI not activated R.M.
PAGE 123
Configuration Using the Web Interface Save to Flash The Save Configuration page saves any changes to the configuration to the flash. If the switch loses power before clicking Save Configuration causes loss of the new settings. Applying changes on web user interface pages do not save the changes to the flash. After selecting Save Configuration, click Save to Flash to save your new configuration. Optionally, you can use the CLI, see Saving to Flash (CLI) on Page 178.
PAGE 124
Configuration Using the Web Interface 124 - Logout RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 125
Configuration Using the Command Line Interface (CLI) Overview The ES8510 provides in-band and out-band configuration methods: • Out-band management means that you configure the ES8510 using the RS-232 console cable and the Command Line Interface (CLI) to access the ES8510 without attaching an admin PC to the network. You can use out-band management if you lose the network connection to the ES8510. • In-band management means that you connect remotely using the ES8510 IP address through the network.
PAGE 126
Configuration Using the Command Line Interface (CLI) Using the Serial Console Comtrol provides one RS-232 RJ45 console cable with the ES8510. Note: A system COM port is required to use a serial console connection. If you do not have an available COM port, use the Using a Telnet/SSH Console procedure on Page 128. 1. Attach the RS-232 DB9 connector to your PC COM port and connect the other end to the Console port of the ES8510.
PAGE 127
Configuration Using the Command Line Interface (CLI) • HyperTerminal (Windows XP, unless installed manually) - Windows XP: Go to Start -> Program -> Accessories -> Communications -> HyperTerminal - Enter a name for the new console connection and click OK. - Enter the IP address in the Host Address text box. - Select TCP/IP (Winsock) in the Connect using drop-list and click Ok. - Set the serial settings using the Serial Settings table (above). - Press the Enter key in the Terminal window.
PAGE 128
Configuration Using the Command Line Interface (CLI) Using a Telnet/SSH Console The ES8510 supports a Telnet console or SSH console with the Command Line Interface (CLI), which is the same as what you see using the RS-232 console port. The SSH connection can secure all the configuration commands you send to the ES8510. SSH is a client/server architecture while the ES8510 is the SSH server. When you want to make SSH connection with the ES8510, you can use PortVision DX or download an SSH client tool.
PAGE 129
Configuration Using the Command Line Interface (CLI) If you selected SSH, click Yes. • Enter the user name (default = admin). • Enter the password (default = admin). If you selected Telnet: • Enter the user name (default = admin). • Enter the password (default = admin). All the commands you see in SSH are the same as the CLI commands you see through the RS-232 console. Command Line Interface Introduction The Command Line Interface (CLI) is the user interface to the ES8510 embedded software.
PAGE 130
Configuration Using the Command Line Interface (CLI) User EXEC Mode When you login to the ES8510 with the CLI, you are in User EXEC mode. In User EXEC mode, you can ping, telnet to a remote device, and show some basic information.
PAGE 131
Configuration Using the Command Line Interface (CLI) 4. Type show ip route and press the Enter key to view the IP routing tables for the ES8510. Switch> show ip route Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, B - BGP, > - selected route, * - FIB route S>* 0.0.0.0/0 [1/0] via 192.168.0.254, vlan1 C>* 127.0.0.0/8 is directly connected, lo C>* 192.168.0.0/16 is directly connected, vlan1 5.
PAGE 132
Configuration Using the Command Line Interface (CLI) Privileged EXEC Mode If you type enable in User EXEC mode, you can access Privileged EXEC mode. In this mode, the ES8510 allows you to view current configuration, reset default, reload switch, show system information, save configuration, and enter Global Configuration mode. Type the following commands and press the Enter key: • configure terminal to access Global Configuration mode (Global Configuration Mode on Page 133). • exit to close the CLI.
PAGE 133
Configuration Using the Command Line Interface (CLI) Global Configuration Mode If you type configure terminal in Privileged EXEC mode, you can then access Global Configuration mode. In Global Configuration mode, you can configure all ES8510 features. Type the following commands and press the Enter key: • interface IFNAME/VLAN, to access the corresponding Interface Configuration mode. • exit to return to Privileged EXEC mode. • ? to see the command list.
PAGE 134
Configuration Using the Command Line Interface (CLI) (Port) Interface Configuration When you type interface IFNAME in Global Configuration mode, you can access Interface Configuration mode. In this mode you can configure port settings. The port interface names for the Fast Ethernet ports are fa1 through fa7. The port interface names for Gigabit Ethernet port are gi8 through gi10. Type the interface name, for example fa1, when you want to enter certain interface configuration mode.
PAGE 135
Configuration Using the Command Line Interface (CLI) (VLAN) Interface Configuration If you type interface VLAN VLAN-ID in Global Configuration mode, you can access VLAN Interface Configuration mode. In this mode, you can configure the settings for the specific VLAN. Switch(config)# interface vlan 1 Switch(config-if)# The VLAN interface name of VLAN 1 is VLAN 1, VLAN 2 is VLAN 2. Type exit to return to the previous mode. Type ? to see the available command list.
PAGE 136
Configuration Using the Command Line Interface (CLI) Mode: Main Function Access and Exit Mode • VLAN Interface Configuration: Configure settings for a • specific VLAN. • Prompt Access VLAN Interface Configuration mode: Type interface VLAN VID in Global Configuration mode. Exit: Type exit or Ctrl+Z to return to Global Configuration mode. Switch(config-vlan)# Type end to return to Privileged EXEC mode. The following are useful commands to save you typing time and to avoid typing errors.
PAGE 137
Configuration Using the Command Line Interface (CLI) VTY Configuration Locked (Error Message) An alert message (VTY configuration is locked by another VTY) appears when multiple users are attempting to configure the ES8510. If the administrator is in Configuration mode, then the web users cannot change settings. The ES8510 allows only one administrator to configure the switch at a time. RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.
PAGE 138
Configuration Using the Command Line Interface (CLI) Basic Settings (CLI) The Basic Setting group provides you with the ability to configure switch information, IP address, User name/ Password of the system. It also allows you to do firmware upgrade, backup and restore configuration, reload factory default, and reboot the system. Optionally, you can use the web user interface for configuration, see Basic Settings on Page 45.
PAGE 139
Configuration Using the Command Line Interface (CLI) IP Configuration IP Address/Mask (192.168.250.250, 255.255.255.0 The enabled bit of the subnet mask is used to represent the number displayed in the web user interface. For example, 8 represents: 255.0.0.0, 16 represents: 255.255.0.0, 24 represents:255.255.255.0. Switch(config)# int vlan 1 Switch(config-if)# ip address dhcp Switch(config-if)# ip address 192.168.250.
PAGE 140
Configuration Using the Command Line Interface (CLI) Time Setting (Continued) Display Switch # sh ntp associations Network time protocol Status: Disabled Primary peer: N/A Secondary peer: N/A Switch # show clock Sun Jan 1 04:14:19 2006 (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London Switch # show clock timezone clock timezone (26) (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London DHCP Server Enable DHCP Server on ES8510 Switch Switch# Switch# configure terminal Switch(config)# ro
PAGE 141
Configuration Using the Command Line Interface (CLI) DHCP Server (cont.
PAGE 142
Configuration Using the Command Line Interface (CLI) DHCP Server (cont.) Switch(config-dhcp)# ip dhcp drop Relay Policy keep Drop/Keep/Replace replace Switch(config-dhcp)# ip dhcp DHCP Relay – DHCP policy Switch(config-dhcp)# ip dhcp Switch(config-dhcp)# ip dhcp relay information policy option82 field relay information policy drop relay information policy keep relay information policy replace DHCP Relay – IP Helper Address Switch(config-dhcp)# ip dhcp helper-address A.B.C.
PAGE 143
Configuration Using the Command Line Interface (CLI) Firmware Upgrade Firmware Upgrade Switch# archive download-sw /overwrite tftp 192.168.11.33 ES8510.bin Firmware upgrading, don't turn off the switch! Tftping file ES8510.bin Firmware upgrading ............................................................ .................... ............................................................ .................... ........................... Firmware upgrade success!! Rebooting.......
PAGE 144
Configuration Using the Command Line Interface (CLI) Port Configuration (CLI) The Port Configuration group allows you to enable/disable port state, or configure port auto-negotiation, speed, duplex, flow control, rate limit control, and port aggregation settings. It also allows you to view port status and aggregation information. Optionally, you can use the web user interface for configuration, see Port Configuration on Page 65.
PAGE 145
Configuration Using the Command Line Interface (CLI) Port Control (continued) Port Control – Flow Control Switch(config-if)# flowcontrol on Flowcontrol on for port 1 set ok! Switch(config-if)# flowcontrol off Flowcontrol off for port 1 set ok! Port Status Switch# show interface fa1 Interface fastethernet1 Administrative Status : Enable Operating Status : Connected Duplex : Full Speed : 100 Flow Control :off Default Port VLAN ID: 1 Ingress Filtering : Disabled Acceptable Frame Type : All Port Security : D
PAGE 146
Configuration Using the Command Line Interface (CLI) Rate Control Switch(config-if)# rate-limit egress Outgoing packets Rate Control ingress Incoming packets – Ingress or Egress Note: To enable rate control, you should select the Ingress or Egress rule first; then assign the packet type and bandwidth.
PAGE 147
Configuration Using the Command Line Interface (CLI) Port Trunking (continued) Switch# show trunk group 1 FLAGS: I -> Individual D -> Port Down Display – Trunk P -> In channel Trunk Group GroupID Protocol Ports --------+---------+-----------------------------------1 LACP 8(D) 9(D) 10(D) Switch# show trunk group 2 FLAGS: I -> Individual P -> In channel D -> Port Down Trunk Group GroupID Protocol Ports --------+---------+-----------------------------------2 Static 6(D) 7(P) Switch# RocketLinx ES8510 and
PAGE 148
Configuration Using the Command Line Interface (CLI) Network Redundancy (CLI) It is critical for industrial applications that the network remains running at all times. The ES8510 supports: • Standard Rapid Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) The ES8510 supports RSTP versions IEEE 802.1D-2004, IEEE 802.1D-1998 STP, and IEEE 802.1w RSTP. • Multiple Spanning Tree Protocol (MSTP) MSTP implements IEEE 802.
PAGE 149
Configuration Using the Command Line Interface (CLI) GLobal (STP, RSTP, and MSTP) (cont.
PAGE 150
Configuration Using the Command Line Interface (CLI) MSTP (cont.
PAGE 151
Configuration Using the Command Line Interface (CLI) MSTP (Continued) Switch(config-mst)# abort discard all mst configuration changes Switch(config)# spanning-tree mst configuration Switch(config-mst)# show pending Abort the Pending MST configuration Setting and go Name [comtrol] (->The name is not applied after Abort settings.) to the configuration Revision 65535 mode.
PAGE 152
Configuration Using the Command Line Interface (CLI) Port Configuration Mode (Continued) Link Type – Share Switch(config-if)# spanning-tree link-type shared Edge Port Switch(config-if)# spanning-tree edge-port enable Switch(config-if)# spanning-tree edge-port disable MSTP Port Configuration Switch(config-if)# spanning-tree mst MSTMAP cost <1-200000000> the value of mst instance port cost Switch(config-if)# spanning-tree mst MSTMAP port-priority <0-240> the value of mst instance port priority in multip
PAGE 153
Configuration Using the Command Line Interface (CLI) Global Information (Continued) Port Info Switch# show spanning-tree interface fa1 Interface fastethernet1 of Bridge is Alternate Blocking Edge Port : Edge (Non-Edge) BPDU Filter : Disabled Link Type : Auto (Point-to-point) BPDU Guard : Disabled Timers : message-age 4, forward-delay 0 BPDUs : sent 26, received 34037 TCNs : sent 0, received 0 Message Expired Count : 0 Forward Transition Count : 8 Aggregation Group: N/A Type: N/A Aggregated with : N/A Por
PAGE 154
Configuration Using the Command Line Interface (CLI) MSTP Information (Continued) Switch# show spanning-tree mst ###### MST00 vlans mapped: 1-4094 Bridge address 00c0.4e30.0001 priority 32768 (sysid 0) Root address 00c0.4e2c.004f priority 32768 (sysid 0) port 10 path cost 400000 Regional root this switch Display all MST Operational max-age 2, hello-time 15, forward-delay 20 Information Configured max-age 2, hello-time 15, forward-delay 20, max-hops 20 Port Role State Cost Prio.
PAGE 155
Configuration Using the Command Line Interface (CLI) Redundant Ring Switch(config)# redundant-ring 1 Ring 1 created Create or configure a Ring Switch(config-redundant-ring)# Note: 1 is the target Ring ID which is going to be created or configured.
PAGE 156
Configuration Using the Command Line Interface (CLI) VLAN (CLI) A Virtual LAN (VLAN) is a logical grouping of nodes for the purpose of limiting a broadcast domain to specific members of a group without physically grouping the members. The VLAN allows you to isolate network traffic so that only members of the VLAN could receive traffic from the same VLAN members.
PAGE 157
Configuration Using the Command Line Interface (CLI) VLAN Port Configuration (continued) Switch# show running-config …… ! interface fastethernet1 Display – Port switchport access vlan 1 Egress Rule (Egress switchport access vlan 3 rule, IP address, switchport trunk native vlan 2 status) ……. interface vlan1 ip address 192.168.250.
PAGE 158
Configuration Using the Command Line Interface (CLI) VLAN Configuration (continued) Display – VLAN table Switch# sh vlan VLAN Name Status Trunk Ports Access Ports ---- --------- ------------ -------------------------1 VLAN1 Static fa1-7,gi8 2 VLAN2 Unused 3 test Static fa4-7,gi8 fa1-3,fa7,gi8 Display – VLAN interface information Switch# show interface vlan1 interface vlan1 is up, line protocol detection is disabled index 14 metric 1 mtu 1500 HWaddr: 00:c0:4e:ff:01:b0 in
PAGE 159
Configuration Using the Command Line Interface (CLI) Private VLAN (CLI) A private VLAN helps to resolve the primary VLAN ID shortage, client ports’ isolation and network security issues. The Private VLAN features provides primary and secondary VLANs within a single switch. Primary VLAN: The uplink port is usually a member of the primary VLAN. A primary VLAN contains promiscuous ports that can communicate with Secondary VLANs. Secondary VLAN: The client ports are usually defined within secondary VLAN.
PAGE 160
Configuration Using the Command Line Interface (CLI) Private VLAN Port Configuration Go to the port configuration Private VLAN Port Type Promiscuous Port Type Switch(config)# interface (port_number, ex: fa1) Switch(config-if)# switchport private-vlan host-association Set the private VLAN host association mapping map primary VLAN to secondary VLAN Switch(config-if)# switchport mode private-vlan Set private-vlan mode Switch(config-if)# switchport mode private-vlan host Set the mode to private-vlan host pro
PAGE 161
Configuration Using the Command Line Interface (CLI) Private VLAN Information (Continued) Switch# show run Building configuration... Current configuration: hostname Switch vlan learning independent ! vlan 1 Running Config ! Information vlan 2 private-vlan primary ! vlan 3 private-vlan isolated ! vlan 4 private-vlan community ! vlan 5 private-vlan community Private VLAN Type ! ……….. ………..
PAGE 162
Configuration Using the Command Line Interface (CLI) Private VLAN Information (Continued) PVLAN Type Switch# show vlan private-vlan type Vlan Type Ports ---- ----------------- ----------------2 primary fa3 3 isolated fa2 4 community fa1 5 community fa4,fa5 10 primary - Host List Switch# show vlan Ports Mode ----- ----------1 normal 2 normal 3 normal 4 normal 5 normal 6 normal 7 host 8 host 9 host 10 promiscuous 162 - Private VLAN (CLI) private-vlan port-list Vlan ---5 4 3 2 RocketLinx ES8510 and ES8
PAGE 163
Configuration Using the Command Line Interface (CLI) Traffic Prioritization (CLI) Quality of Service (QoS) provides a traffic prioritization mechanism which allows you to deliver better service to certain flows. QoS can also help to alleviate congestion problems and ensure high-priority traffic is delivered first. This section allows you to configure Traffic Prioritization settings for each port with regard to setting priorities.
PAGE 164
Configuration Using the Command Line Interface (CLI) QoS Setting (cont.
PAGE 165
Configuration Using the Command Line Interface (CLI) CoS-Queue Mapping (cont.) Switch# sh qos cos-map CoS to Queue Mapping : CoS Queue ---- + -----0 1 1 0 Display – CoS-Queue mapping 2 0 3 1 4 2 5 2 6 3 7 3 DSCP-Queue Mapping Switch(config)# qos dscp-map PRIORITY Assign an priority (63 highest) Switch(config)# qos dscp-map 0 Format QUEUE Assign an queue (0-3) Format: qos dscp-map priority_value queue_value. Switch(config)# qos dscp-map 0 1 Map DSCP 0 to Queue 1 The TOS/DSCP to queue mapping is set ok.
PAGE 166
Configuration Using the Command Line Interface (CLI) Multicast Filtering (CLI) For multicast filtering, the ES8510 uses IGMP (Internet Group Management Protocol) Snooping technology. IGMP is an internet protocol that provides a way for internet device to report its multicast group membership to adjacent routers. Multicasting allows one computer on the internet to send data to a multitude of other computers that have identified themselves as being interested in receiving the originating computers data.
PAGE 167
Configuration Using the Command Line Interface (CLI) IGMP Snooping (Continued) Switch# sh ip igmp interface vlan1 enabled: Yes version: IGMPv1 query-interval; 125s Display – IGMP Snooping Setting query-max-response-time: 10s Switch# sh ip igmp snooping IGMP snooping is globally enabled Vlan1 is IGMP snooping enabled Vlan2 is IGMP snooping enabled Vlan3 is IGMP snooping disabled Switch# sh ip igmp snooping multicast all VLAN IP Address Display – IGMP Table ---- --------------- 1 1 Type Ports -------
PAGE 168
Configuration Using the Command Line Interface (CLI) IGMP Query (Continued) Switch# sh ip igmp interface vlan1 enabled: Yes version: IGMPv2 query-interval: 125s query-max-response-time: 10s Display Switch# show running-config …. ! interface vlan1 ip address 192.168.250.17/24 ip igmp no shutdown ! …….
PAGE 169
Configuration Using the Command Line Interface (CLI) SNMP (CLI) Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. The ES8510 supports SNMP v1 and v2c and V3. An SNMP managed network consists of two main components: agents and a manager. An agent is a management software module that resides in a managed switch.
PAGE 170
Configuration Using the Command Line Interface (CLI) Security (CLI) The ES8510 provides several security features for you to secure your connection. Optionally, you can use the web user interface for configuration, see Security on Page 104. This table provides information about the command lines for security configuration. Port Security Add MAC Port Security Switch(config)# mac-address-table static 00c0.4e2C.
PAGE 171
Configuration Using the Command Line Interface (CLI) 802.
PAGE 172
Configuration Using the Command Line Interface (CLI) Warnings (CLI) The ES8510 provides several types of warning features for you to remotely monitor the status of the attached devices or changes in your network. The features include Fault Relay, System Log and SMTP Email Alert. Optionally, you can use the web user interface for configuration, see Warning on Page 110. This table provides detailed information about the command lines of the warning configuration.
PAGE 173
Configuration Using the Command Line Interface (CLI) Fault Relay Output (cont.
PAGE 174
Configuration Using the Command Line Interface (CLI) Syslog Configuration Local Mode Switch(config)# log syslog local Server Mode Switch(config)# log syslog remote 192.168.250.33 Both Switch(config)# log syslog local Switch(config)# log syslog remote 192.168.250.33 Disable Switch(config)# no log syslog local SMTP Configuration SMTP Enable Switch(config)# smtp-server enable email-alert SMTP Email Alert set enable ok. Sender mail Switch(config)# smtp-server server 192.168.250.
PAGE 175
Configuration Using the Command Line Interface (CLI) Monitor and Diag (CLI) The ES8510 provides several types of features for you to monitor the status of the switch or diagnostic for you to check the problem when encountering problems related to the switch. The features include MAC Address Table, Port Statistics, Port Mirror, Event Log, and Ping. Optionally, you can use the web user interface for configuration, see Monitor and Diag on Page 115.
PAGE 176
Configuration Using the Command Line Interface (CLI) MAC Address Table (continued) Show MAC Address Table – Static MAC addresses Switch# show mac-address-table static Destination Address Address Type Vlan ------------------- --------------- ------00c0.4e2C.0101 Static 1 00c0.4e2C.0102 Static 1 Show Aging timeout time Switch# show mac-address-table aging-time the mac-address-table aging-time is 300 sec.
PAGE 177
Configuration Using the Command Line Interface (CLI) Port Mirroring (continued) Display Switch# show mirror Mirror Status : Enabled Ingress Monitor Destination Port : fa6 Egress Monitor Destination Port : fa6 Ingress Source Ports :fa1,fa2, Egress Source Ports :fa1,fa2, Event Log Display Switch# <1>Jan <2>Jan <3>Jan <4>Jan show event-log 1 02:50:47 snmpd[101]: 1 02:50:50 snmpd[101]: 1 02:50:51 snmpd[101]: 1 02:50:53 snmpd[101]: Event: Event: Event: Event: Link Link Link Link 4 5 5 4 Down. Up.
PAGE 178
Configuration Using the Command Line Interface (CLI) Saving to Flash (CLI) Save Configuration allows you to save any configuration you just made to the flash. Powering off the switch without saving the configuration causes loss of the new settings. Saving to Flash SWITCH# write Building Configuration… [OK] Save to Flash Switch# copy running-config startup-config Building Configuration...
PAGE 179
Complete CLI List This section provides the complete listing of RocketLinx ES8510 commands with the supporting options: • User EXEC Mode • Privileged EXEC Mode on Page 180 • Global Configuration Mode on Page 185 • Port Interface Configuration Mode on Page 190 • VLAN Interface Configuration Mode on Page 192 User EXEC Mode For information about accessing User EXEC mode, see User EXEC Mode on Page 179. Switch> list exit list ping A.B.C.
PAGE 180
Complete CLI List Privileged EXEC Mode For information about accessing Privileged EXEC mode, see Privileged EXEC Mode on Page 180.
PAGE 181
Complete CLI List Privileged EXEC Mode (continued) dot1x initialize interface IFNAME dot1x reauthenticate interface IFNAME end exit list no debug dot1x all no debug dot1x errors no debug dot1x events no debug dot1x packets no debug dot1x registry no debug dot1x state-machine no debug gvrp (all|rcv|tx|gvrp_event|vlan_event) no debug ip dhcp (all|event) no debug ip igmp no debug ip igmp snooping (all|group|management|router|timer) no debug l2 mac (all|trace|debug) no debug lacp (all|event|fsm|misc|packet) no
PAGE 182
Complete CLI List Privileged EXEC Mode (continued) show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show dot1q-tunnel dot1x dot1x all dot1x authentic-method dot1x interface IFNAME dot1x radius dot1x statistics interface IFNAME dot1x username ethernet-ip ethertype event-log garp timer [IFNAME] gvrp confi
PAGE 183
Complete CLI List Privileged EXEC Mode (continued) show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show mac-address-table mac-address-table aging-time mac-address-table dynamic mac-address-table dynamic address MACADDR mac-address-table dynamic interface IFNAME mac-address-table dynamic vlan VLANID mac
PAGE 184
Complete CLI List Privileged EXEC Mode (continued) show spanning-tree summary show startup-config show trunk group [1-5] show version show vlan show vlan (static|dynamic) [VLANID] show vlan VLANID show vlan management show vlan name VLANAME show vlan private-vlan show vlan private-vlan port-list show vlan private-vlan type show warning-event telnet WORD telnet WORD PORT terminal length <0-512> terminal no length traceroute WORD write write file write memory write terminal 184 - Privileged EXEC Mode Rocke
PAGE 185
Complete CLI List Global Configuration Mode For information about accessing Global Configuration mode, see Global Configuration Mode on Page 185. Switch(config)# list administrator NAME PASSWORD arp A.B.C.D H.H.H auth radius server A.B.C.
PAGE 186
Complete CLI List Global Configuration Mode (continued) log stdout log syslog local log syslog remote A.B.C.
PAGE 187
Complete CLI List Global Configuration Mode (continued) no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no log file log stdout log syslog local log syslog remote loop-protect transmit-interval mac-address-table aging-time mac-address-table multicast MACADDR vlan VLANID interface IFLIST mac-address-table multicast filtering mac-address-table static MACADDR vlan VLANID interface IFNAME mirror destination
PAGE 188
Complete CLI List Global Configuration Mode (continued) no warning-event ring no warning-event sfp no warning-event time-sync no write-config (daemon|integrated) ntp peer (enable|disable) ntp peer (primary|secondary) IPADDRESS qos cos-map PRIORITY QUEUE qos dscp-map PRIORITY QUEUE qos queue-sched (wrr|sp) redundant-ring <0-31> relay <1-2> di <1-2> (high|low) relay <1-2> dry <0-4294967295> <0-4294967295> relay <1-2> ping WORD relay <1-2> ping WORD reset <1-65535> <0-65535> relay <1-2> port PORTLIST relay <1
PAGE 189
Complete CLI List Global Configuration Mode (continued) spanning-tree mst max-hops <1-40> spanning-tree mst sync vlan <1-4094> spanning-tree pathcost method (long|short) spanning-tree priority <0-61440> spanning-tree transmission-limit <1-10> trunk group <1-5> IFLIST vlan <1-4094> vlan learning (independent|shared) warning-event (coldstart|warmstart) warning-event (linkdown|linkup) [IFLIST] warning-event authentication warning-event di <1-2> warning-event fault-relay warning-event loop-protect warning-even
PAGE 190
Complete CLI List Port Interface Configuration Mode For information about accessing Port Interface Configuration mode, see Port Interface Configuration Mode on Page 190. Switch(config)# interface fa1 Switch(config-if)# list acceptable frame type (all|vlantaggedonly) auto-negotiation description .
PAGE 191
Complete CLI List Port Interface Configuration Mode (continued) no spanning-tree link-type no spanning-tree mst MSTMAP cost no spanning-tree mst MSTMAP port-priority no spanning-tree port-priority no spanning-tree stp-state no speed no switchport access vlan VLANID no switchport block no switchport dot1q-tunnel mode (access|uplink) no switchport mode private-vlan host no switchport mode private-vlan promiscuous no switchport port-security no switchport private-vlan host-association no switchport trunk nati
PAGE 192
Complete CLI List VLAN Interface Configuration Mode For information about accessing VLAN Interface Configuration mode, see VLAN Interface Configuration Mode on Page 192. Switch(config-if)# interface vlan1 Switch(config-if)# list dno description no ip address A.B.C.D/M no ip dhcp client no ip igmp no ipv6 address X:X::X:X/M no shutdown quit shutdown description .LINE end exit ip address A.B.C.
PAGE 193
ModBus TCP /IP Support This section provides the following information: • Modbus TCP/IP Function Codes on Page 194 • Error Checking on Page 194 • Exception Response on Page 195 • Modbus TCP Register Table on Page 195 • CLI Commands for Modbus TCP/IP on Page 202 Overview The ES8510 supports Modbus TCP/IP communications through the CLI, which does not support Modbus ASCII or Modbus RTU. This functionality is not available on a web user interface page.
PAGE 194
ModBus TCP /IP Support The ES8510 operates as slave/server device, while a typical master/client device is a host computer running appropriate application software, for example, a SCADA / HMI system. The ES8510 can be polled through Ethernet, thus the Modbus TCP/IP master can read or write to the Modbus registers provided by the Modbus TCP/IP.
PAGE 195
ModBus TCP /IP Support Exception Response If an error occurs, the slave sends an exception response message to master consisting of the slave address, function code, exception response code and error check field. In an exception response, the slave sets the highorder bit (MSB) of the response function code to one. Code Name Descriptions 01 Illegal Function The message function received is not an allowable action. 02 Illegal Data Address The address referenced in the data field is not valid.
PAGE 196
ModBus TCP /IP Support Word Address Data Type Description System Information (cont.
PAGE 197
ModBus TCP /IP Support Word Address Data Type Description Firmware Release Date 0x020A 2 words Firmware was released on 2010-08-11 at 09 o’clock Word 0 = 0x0B09 3 words Word 1 = 0x0A08 Ethernet MAC Address For example: MAC = 01-02-03-04-05-06 Word 0 Hi byte = 0x01 Word 0 Lo byte = 0x02 0x020C Word 1 Hi byte = 0x03 Word 1 Lo byte = 0x04 Word 2 Hi byte = 0x05 Word 2 Lo byte = 0x06 IP address For example: IP = 192.168.250.
PAGE 198
ModBus TCP /IP Support Word Address Data Type Description System Information (cont.
PAGE 199
ModBus TCP /IP Support Word Address Data Type Description Port Information (32 Ports) 0x1000 to 0x11FF 16 words Port Description Administrative Status 0x1200 to 0x121F 1 word 0x0000: disable 0x0001: enable Operating Status 0x1220 to 0x123F 1 word 0x0000: disable 0x0001: enable 0xFFFF: unavailable Duplex 0x0000: half 0x0001: full 0x1240 to 0x125F 1 word 0x0003: auto (half) 0x0004: auto (full) 0x0005: auto 0xFFFF: unavailable Speed 0x0001: 10 0x0002: 100 0x0003: 1000 0x0004: 2500 0x0005: 10000
PAGE 200
ModBus TCP /IP Support Word Address Data Type Description Port Information (32 Ports - cont.
PAGE 201
ModBus TCP /IP Support Word Address Data Type Description SFP DDM Information (32 Ports) 0x1800 to 0x181F 1 words Temperature 0x1820 to 0x185F 2 words Alarm Temperature 0x1860 to 0x187F 1 words Tx power 0x1880 to 0x18BF 2 words Warning Tx power 0x18C0 to 0x18DF 1 words Rx power 0x18E0 to 0x191F 2 words Warning Rx power 0x1920 to 0x1FFF 1760 words Reserved address space Inbound Packet Information 0x2000 to 0x203F 0x2040 to 0x207F 0x2080 to 0x20BF 0x20C0 to 0x20FF 0x2100 to 0x213F 0x2
PAGE 202
ModBus TCP /IP Support Word Address Data Type Description Number of Frames Received and Transmitted with a Length (Octets) 0x2A00 to 0x2A3F 0x2A40 to 0x2A7F 0x2A80 to 0x2ABF 0x2AC0 to 0x2AFF 0x2B00 to 0x2B3F 0x2B40 to 0x2B7F 2 words 2 words 2 words 2 words 2 words 2 words 64 65 to 127 128 to 255 256 to 511 512 to 1023 1024 to maximum size CLI Commands for Modbus TCP/IP The CLI commands for Modbus TCP/IP are listed in the following table.
PAGE 203
Technical Support Comtrol SFP Modules Comtrol provides a variety of SFP transceivers. These certified SFP transceivers can be identified by the RocketLinx ES8510 and displayed in the web user interface. We recommend using Comtrol SFP transceivers when configuring your RocketLinx ES8510 and RocketLinx ES8510-XT. Note: Low quality SFP transceivers may result in poor network performance and may not meet claimed distance or temperature ratings.
PAGE 204
Technical Support 204 - Comtrol Support RocketLinx ES8510 and ES8510-XT User Guide: 2000513 Rev.