Specifications

www.camfilfarr.com
Camfil Farr | 1 North Corporate Drive, Riverdale, NJ 07457 | Tel: [phone]
PERFORMANCE DATA (continued)
Camfil Farr 30/30
®
Part Number
Nominal
Depth
(inches)
Nominal
Size
(inches)
Actual Size
(inches)
Initial
Resistance
(inches w.g.)
Airflow
Capacity
(cfm)
Total Media
Area
(sq. ft.)
Pleats per
Linear Foot
Depth Height Width
059413-004
4
20 x 16
3.75
19.38 15.38
0.27
1100 15.7
11 pleats per
linear foot
059413-003 20 x 20 19.38 19.38 1390 18.9
059413-002 24 x 12 23.38 11.38 1000 13.9
059413-009 24 x 18 23.38 17.38 1500 20.2
059413-008 24 x 20 23.38 19.38 1670 22.7
059413-001 24 x 24 23.38 23.38 2000 27.7
059413-005 25 x 16 24.38 15.38 1390 19.7
059413-006 25 x 20 24.38 19.38 1740 23.6
059413-010 25 x 25 24.38 24.38 2170 30.0
059413-007 25 x 29 24.38 28.38 2520 35.4
4” Deep Filter (actual filter depth 3.75”)
4” deep 30/30 is available with a header
for side-access housing installation.
Request Product Sheet 1003.
Data Notes:
1.0” w.g. recommended final resistance for all depths. System design may dictate an alternative changeout point. Contact factory
for guidance.
The 30/30 has been listed by Underwriters Laboratories as UL 900.
Maximum operating temperature 200º F (93º C).
2” and 4” deep filters rated at 250 feet per minute (fpm) medium and 500 fpm high. 1” deep filter’s rated at 175 fpm medium and
350 fpm high.
For product specification in RTF format please go to www.camfilfarr.com.
© Copyright Camfil Farr # 1002 - 0212
Specification
1.0 General
1.1 - Air filters shall be medium efficiency ASHRAE pleated
panels consisting of cotton and synthetic media, welded wire
media support grid, and beverage board enclosing frame.
1.2 - Sizes shall be noted on drawings or other supporting
materials.
2.0 Construction
2.1 - Filter media shall be a cotton and synthetic blend, lofted
to a uniform depth of 0.15”, and formed into a uniform radial
pleat.
2.2 - A welded wire grid, spot-welded on one-inch centers
and treated for corrosion resistance shall be bonded to the
downstream side of the media to maintain radial pleats and
prevent media oscillation.
2.3 - An enclosing frame of no less than 28-point high wet-
strength beverage board shall provide a rigid and durable
enclosure. The frame shall be bonded to the media on all
sides to prevent air bypass. Integral diagonal support mem-
bers on the air entering and air exiting side shall be bonded
to the apex of each pleat to maintain uniform pleat spacing in
varying airflows.
3.0 Performance
3.1 - The filter shall have a Minimum Efficiency Reporting Value of
MERV 8 when evaluated under the guidelines of ASHRAE Standard
52.2. It shall also have a MERV-A of 8 when tested per Appendix
J of the same standard. The media shall maintain or increase in
efficiency over the life of the filter.
3.2 - Initial resistance to airflow shall not exceed 0.23”, 0.31” or
0.27” w.g. at an airflow of 350, 500 or 500 fpm on 1”, 2” or 4”
deep models respectively.
3.3 - The filter shall have an Energy Cost Index (ECI) value of five
stars.
3.4 - Filter shall be listed UL 900 by Underwriters Laboratories.
3.5 - Manufacturer shall provide evidence of facility certification to
ISO 9001:2008.
3.6 - Manufacturer shall guarantee the integrity of the filter pack to
2.0” w.g.
Supporting Data - Provide product test report including all details
as prescribed in ASHRAE Standards 52.2, including Appendix J.
Air filters shall be Camfil Farr 30/30 or equal.