Industrial Managed PoE Switch 8 - 10/100BASE-TX PoE Plus Ports 2 - Gigabit RJ45/SFP Combo Ports User Guide
Copyright Notice Comtrol and RocketLinx are trademarks of Comtrol Corporation. Microsoft and Windows are trademarks of Microsoft Corporation. FireFox is a trademark of Mozilla Foundation. PuTTY is a copyright of Simon Tatham. Other product names mentioned herein may be trademarks and/or registered trademarks of their respective owners. Fourth Edition, October 21, 2014 Copyright © 2012-2014. Comtrol Corporation. All Rights Reserved.
Table of Contents Introduction .......................................................................................................................................... 7 Hardware Installation ........................................................................................................................ 9 Connect the Power and Ground................................................................................................................. 9 Connect the Digital Inputs and Relay Outputs .....
Table of Contents Backup and Restore.................................................................................................................................. 60 Backup the Configuration - Local File Method ................................................................................ 61 Restore the Configuration - Local Method........................................................................................ 61 Backup the Configuration - TFTP Server Method ..................................
Table of Contents Security ........................................................................................................................................................ 111 Port Security ........................................................................................................................................... 111 IP Security............................................................................................................................................... 112 802.
Table of Contents Complete CLI List............................................................................................................................191 User EXEC Mode ........................................................................................................................................ 191 Privileged EXEC Mode ............................................................................................................................. 192 Global Configuration Mode................
Introduction The ES7510-XT is an industrial ten port managed PoE Plus switch that provides: • Eight 10/100BASE-TX PoE Plus ports that are IEEE 802.3af (15.4W) and IEEE 802.
Introduction 8 - Introduction RocketLinx ES7510-XT User Guide: 2000571 Rev.
Hardware Installation You can use the following subsections to install the RocketLinx ES7510-XT: • Connect the Power and Ground • Connect the Digital Inputs and Relay Outputs on Page 11 • Mount the ES7510-XT on Page 12 • Connect the Ethernet Ports on Page 13 • Connect SFP Transceivers (Combo Ports 9-10) on Page 14 • LED Descriptions on Page 14 • Reset Button on Page 15 Connect the Power and Ground You can use the following procedure to connect power and the ground to the ES7510-XT. 1.
Hardware Installation ELectrical Specifications Value Power Input Voltage DC1/DC2 IEEE 802.3af 46-57VDC IEEE 802.3at 50-57VDC Maximum PoE Power/Port IEEE 802.3af 15.4W IEEE 802.3at 30W Power Budget DC1/DC2 120W Power Consumption Without PD 15W load (maximum) PoE with PD 140W load (maximum) • PWR1 and PWR2 support power redundancy and reverse polarity protection. • Accepts a positive or negative power source but PWR1 and PWR2 must apply to the same mode.
Hardware Installation Connect the Digital Inputs and Relay Outputs The ES7510-XT provides one digital input and one digital output (dry relay output) on the terminal block connectors on the bottom of the unit.
Hardware Installation Connect the Surge/Lightening Protection Connect a ground wire between the earth ground (surge) screw and earth ground to provide enhanced surge and lighting immunity. 1. Loosen the earth ground screw located on the back of the unit next to the compliance label. 2. Insert the ground wire (12-24AQWG). 3. Tighten the surge screw after the ground wire is inserted. Make sure that you remove the surge ground screw before insulation/Hi-pot testing.
Hardware Installation Connect the Ethernet Ports You can use the following information to connect standard Ethernet cables between the ES7510-XT Ethernet ports and the network nodes. • Ports 1-8 are Fast Ethernet (10/100BASE-TX) PoE ports that are IEEE 802.3af (PoE) and IEEE 802.3at (PoE Plus) compliant. • Ports 9-10 are RJ45/SFP Combo Gigabit ports that support 10/100/1000BASE-TX, 100BASE-FX, and 1000BASE-X with digital diagnostic monitoring (DDM).
Hardware Installation Connect SFP Transceivers (Combo Ports 9-10) The ES7510-XT provides two SFP ports combined with RJ45 Gigabit Ethernet ports (Ports 9-10). The SFP ports accept standard mini GBIC DDM SFP transceivers that support 100BASE-FX/1000BASE-X. To ensure system reliability, Comtrol recommends using Comtrol certified SFP Transceivers. The SFP cage is 2 x1 design. 1. Plug the SFP transceiver into the SFP fiber transceiver. 2. Connect the transmit channel to the receive channel at each end. 3.
Hardware Installation Reset Button The ES7510-XThas a reset button that you can use to reboot the ES7510-XT or reset the configuration to the factory default. Reset Button Description Depress 5 Seconds This reboots the ES7510-XT without changing the configuration. Depress > 10 Seconds This loads the factory default configuration values into the ES7510-XT including the IP address. The Reset button is located on the front panel of the ES7510-XT below the Console port.
Hardware Installation 16 - Reset Button RocketLinx ES7510-XT User Guide: 2000571 Rev.
Using PortVision DX There are several ways to configure network information. Comtrol Technical Support recommends connecting the ES7510-XT to a PC or laptop running Windows and installing PortVision DX for initial configuration.
Using PortVision DX PortVision DX Overview PortVision DX automatically detects Comtrol Ethernet attached products physically attached to the local network segment so that you can configure the network address, upload firmware, and manage the following products: • RocketLinx switches • DeviceMaster family - DeviceMaster PRO - DeviceMaster RTS - DeviceMaster Serial Hub - DeviceMaster UP - DeviceMaster 500 • DeviceMaster LT • IO-Link Master family In addition to identifying Comtrol Ethernet a
Using PortVision DX Installing PortVision DX During initial configuration, PortVision DX automatically detects and identifies ES7510-XT switches, if they are in the same network segment. Use the Software and Documentation CD that came with the ES7510-XT to check for the latest version of PortVision DX or use the link below to download the latest version. 1.
Using PortVision DX 6. Click Next to configure the shortcuts. 7. Click Install. 8. Depending on the operating system, you may need to click Yes to the Do you want to allow the following program to install software on this computer? query. 9. Click Launch PortVision DX and Finish in the last installation screen. 10. Depending on the operating system, you may need to click Yes to the Do you want to allow the following program to make changes to this computer? query. 11.
Using PortVision DX Configuring the Network Settings The ES7510-XT has the following default values when shipped from the factory: • IP address: 192.168.250.250 • Subnet mask: 255.255.0.0 • Gateway address: 192.168.250.1 Use the following procedure to change the default network settings on the ES7510-XT for your network. 1. If necessary, start PortVision DX using the PortVision DX desktop shortcut or from the Start button, click All Programs > Comtrol > PortVision DX > PortVision DX.
Using PortVision DX 4. Highlight the ES7510-XT for which you want to program network information and open the Properties screen using one of these methods. • Double-click the ES7510-XT in the Device Tree or Device List pane. • Highlight the ES7510-XT in the Device Tree or Device List pane and click the Properties button. • Right-click the ES7510-XT in the Device Tree or Device List pane and click Properties in the popup menu • Highlight the ES7510-XT, click the Manage menu and then Properties.
Using PortVision DX 5. Optionally, rename the ES7510-XT in the Device Name field for a PortVision DX friendly name. The default name displays as Device and the last three sets of hex numbers from the MAC address. Note: The MAC address and Device Status fields are automatically populated and you cannot change these values. 6. Optionally, enter the serial number, which is on a label on the ES7510-XT. 7. Select DHCP IP or Static IP for the IP Mode. • If you select DHCP IP, go to Step 8.
Using PortVision DX Checking the Firmware Version Checking your web interface and bootloader versions is easy in PortVision DX. Comtrol recommends loading the latest firmware and bootloader so that you have all of the latest feature enhancements and bug fixes. 1. If the ES7510-XT is not displayed in PortVision DX, click the Scan button. 2. Select the Comtrol Ethernet attached product type and click the Scan button. 3. Locate the ES7510-XT in the Device List pane.
Using PortVision DX Uploading the Latest Firmware or Bootloader You can use the following procedure to upload the latest firmware or bootloader. 1. If you have not done so, download the latest firmware and bootloader using the previous subsection. 2. Right-click the ES7510-XT in the Device List pane that you want to update, click Advanced --> Upload firmware. 3. Navigate to the location of the firmware files, select the appropriate file, and then click Open. 4. Click Yes to the Upload Firmware message. 5.
Using PortVision DX Uploading Firmware to Multiple ES7510-XT Switches You can use this procedure if your ES7510-XT is connected to the host PC, laptop, or if the ES7510-XT resides on the local network segment. Note: Technical support does not advise uploading bootloader to multiple ES7510-XT switches. Remember that uploading firmware reboots the ES7510-XT, which depending on your network connections may cause firmware uploading to fail on another ES7510-XT. 1.
Using PortVision DX Adding a New Device in PortVision DX You can add a new ES7510-XT manually, if you do not want to scan the network to locate it or you want to preconfigure an ES7510-XT before connecting it to the network. Optionally, you can also add unmanaged devices or RocketLinx switches to maintain information about devices on the network. See the PortVision DX help system for additional information about adding unmanaged RocketLinx switches or third party devices or switches.
Using PortVision DX 6. Enter the IP Address for the ES7510-XT. It is not necessary to enter the Subnet Mask and Default Gateway 7. Click Ok to close the Add New Device window. It may take a few moments to save the ES7510-XT. 8. If necessary, click Refresh for the new RocketLinx to display in the Device Tree or Device List panes. The RocketLinx shows OFF-LINE if it is not connected to the local network or if an incorrect IP address was entered.
Using PortVision DX Using the LED Tracker RocketLinx managed switches support the LED Tracker feature, which allows you to toggle on/off the LEDs on a specific device so that you can locate the physical unit. Use this procedure to toggle the LED Tracker feature on RocketLinx switches. 1. Right-click the ES7510-XT in the Device List pane, click Tracker, and then click ON. The ES7510-XT SYS LED will flash for five seconds. 2.
Using PortVision DX Customizing PortVision DX You can customize how PortVision DX displays the devices. You can even create sessions tailored for specific audiences. You can also add shortcuts to other applications using Tools > Applications > Customize feature. The following illustrates how you can customize your view. See the PortVision DX Help system for detailed information about modifying the view. For example, the above screen shot illustrates devices layered in folders.
Using PortVision DX Accessing RocketLinx Documentation from PortVision DX You can use this procedure in PortVision DX to download and open the previously downloaded documents for the RocketLinx. How to Download Documentation Use this procedure to initially download a document or documents. 1. If necessary, open PortVision DX. 2. Click Help > Documentation. 3.
Using PortVision DX How to Open Previously Downloaded Documents Use the following procedure to access previously downloaded documents in PortVision DX. Note: Optionally, you can browse to the Program Files (x86) > Comtrol > PortVision DX > Docs subdirectory and open the document. 1. If necessary, open PortVision DX > Start/Programs > Comtrol > PortVision DX > PortVision DX or use the desktop shortcut. 2. Click Help > Documentation. 3.
Configuration Using the Web User Interface The ES7510-XT provides in-band and out-band configuration methods: • Out-band management means that you configure the ES7510-XT using the RS-232 console cable and the Command Line Interface (CLI) to access the ES7510-XT without attaching an admin PC to the network. You can use out-band management if you lose the network connection to the ES7510-XT. The CLI and Telnet are discussed in Configuration Using the Command Line Interface (CLI) on Page 131.
Configuration Using the Web User Interface Web User Interface The ES7510-XT web management page was developed with Java. You can use any standard web browser, which is compatible with Java Runtime to configure and communicate with the ES7510-XT from anywhere on the network. If you did not program the IP address for your network using PortVision DX (Programming Network Information on Page 20), you need to change your computer IP address to 192.168.250.x (Network Mask: 255.255.0.0).
Configuration Using the Web User Interface 4. Enter the user name, the password, and click OK. The default user name and password are both admin. The Welcome page of the web management interface then appears. 5. If you have not done so, you can change the ES7510-XT IP address to meet your network environment. a. Double-click Basic Setting. b. Click IP Configuration. To use static addressing, enter a valid IP add dress, subnet mask and default gateway.
Configuration Using the Web User Interface Secure Web User Interface The ES7510-XT web user interface also provides secured management through an HTTPS login so that all of the configuration commands are secure. If you did not program the IP address for your network using PortVision DX (Configuring the Network Settings on Page 21), you need to change your computer IP address to 192.168.250.x (Network Mask: 255.255.0.0). The default IP address for the ES7510-XT is 192.168.250.250. 1.
Configuration Using the Web User Interface Windows XP and Windows Server 2003 a. Click No when the popup screen appears and requests you to trust the secured HTTPS connection distributed by the ES7510-XT. b. Click Always trust content from this publisher and then Run when requested to run the application (IP address) in the Warning - Security message. Windows Vista - Windows 7 a. Click the Continue button. b. If necessary, click Show all content. c.
Configuration Using the Web User Interface 4. Enter the user name and the password and click OK. The default user name and password are both admin. The Welcome page of the web management interface then appears. 5. If you have not done so, you can change the ES7510-XT IP address to meet your network environment. a. Double-click Basic Setting. b. Click IP Configuration. c. - To use static addressing, enter a valid IP address, subnet mask and default gateway.
Configuration Using the Web User Interface Feature Overview The following table provides detailed information about ES7510-XT features and provides the location of the configuration information in the web user interface. Type 802.1x Port-Based Network Access Control Configuration Category 802.
Configuration Using the Web User Interface Type Category Details • DHCP Server Configuration on Page 55 DHCP Server Configuration DSCP-Queuing Mapping Event Selection DHCP Leased Entries on Page 57 DHCP Server Configuration - Excluded Addresses and Manual Binding Port and IP Address Option 82 • DHCP Leased Entries DHCP Relay Agent on Page 58 • DHCP Relay Agent DSCP-Queue Mapping on Page 103 • DSCP 0 through 7 • Queue 0 through 3 • Queue 3 highest priority • Device Cold Start • Devic
Configuration Using the Web User Interface Type IGMP Query IGMP Snooping Category IGMP Query on Page 106 IGMP Snooping on Page 105 Details • Version - Version 1, Version 2, or Disable • Query Intervals • Query Maximum Response Time • Enable/Disable • VID • Port by Port IGMP Snooping Table - IP Address - VID IP Configuration IP Security Loop Protection MAC Address Table (8K) MSTP Configuration Basic Settings on Page 48 IP Security on Page 112 Loop Protection on Page 90 MAC Address T
Configuration Using the Web User Interface Type MSTP Information Category Details • Instance ID • Root Information - MSTP Information on Page 86 • Root Address Root Priority Root Port Root Path Cost Maximum Age Hello Time Forward Delay Port Information - Role Port State Path Cost Port Priority Link Type Edge Port Instance ID MSTP Port Configuration Ping Utility PoE Control MSTP Port Configuration on Page 85 Ping Utility on Page 128 • Port • Path Cost • Priority • Link Type • Edge P
Configuration Using the Web User Interface Type PoE Status Port Control Category PoE Status on Page 77 Port Control on Page 67 Port Mirror Mode Port Mirroring on Page 125 Port Security Port Security on Page 111 Details • Power Budget • Output Power • Power Budget Warning Level • Utilization • Event • PoE Mode Port by Port: • Operation Status • PD Class • Budget (W) • Consumption (W) • Voltage • Current • Enable/Disable Port State • Speed/Duplex - Auto-Negotiation, 10 Fu
Configuration Using the Web User Interface Type Port Status Category Port Status on Page 69 Details • Port Type • Link - Up/Down • State - Enable/Disable • Speed/Duplex • Flow Control • SFP Vendor, Wavelength, and Distance • SFP DDM - Temperature, Tx Power, and Rx Power Aggregation Settings • Port Trunk Group ID - Trunk 1-8 Aggregation Setting on Page 71 Trunk Type - Static or 802.
Configuration Using the Web User Interface Type Redundant Ring Redundant Ring Information Reset/Reboot SNMP Configuration SNMP Traps Category Details • Ring ID and Name • Ring Configuration - Redundant Ring on Page 88 Redundant Ring Information on Page 89 Load Default on Page 66 System Reboot on Page 66 SNMP Configuration on Page 108 SNMP Traps on Page 110 ID Name Version (Super Ring and Rapid Super Ring) Device Priority Ring Port Path Cost Ring Port2 Path Cost Rapid Dual Homing Ring Status
Configuration Using the Web User Interface Type STP Configuration STP Information Category STP Configuration on Page 79 STP Information on Page 81 Details • STP, RSTP, MSTP, or Disable • Bridge Address • Bridge Priority • Maximum Age • Hello Time • Forward Delay • Root Information - • Root Address Root Priority Root Port Root Path Cost Maximum Age Hello Time Forward Delay Port Information - Role Port State Path Cost Port Priority Link Type Edge Port Aggregated (D/Type) Port by Port
Configuration Using the Web User Interface Type Topology Discovery Unknown Multicast Upgrade Firmware VLAN Configuration VLAN Port Configuration VLAN Table Warning - SMTP Configuration Category Topology Discovery (LLDP) on Page 127 Unknown Multicast on Page 106 Firmware Upgrade on Page 64 VLAN Configuration on Page 93 VLAN Port Configuration on Page 92 VLAN Table on Page 97 SMTP Configuration on Page 121 RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Basic Settings The Basic Setting group allows you the ability to configure switch information, IP address, User name/ Password of the system. It also allows you to do firmware upgrade, backup and restore configuration, reload factory default, and reboot the system.
Configuration Using the Web Interface Switch Setting Page (Continued) Device MAC Displays a unique hardware address (MAC address) assigned at the factory. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 130), if you want to maintain these settings if the ES7510-XT is powered off. Admin Password You can change the user name and the password here to enhance security. Admin Password Page Administrator Name You can enter a new user name here. The default name is admin.
Configuration Using the Web Interface IP Configuration This function allows you to configure the ES7510-XT’s IP address settings. IP Configuration Page DHCP Client You can select to Enable or Disable the DHCP Client function. When the DHCP Client function is enabled, an IP address is assigned to the switch from the network’s DHCP server. In this mode, the default IP address is replaced by the one assigned by DHCP server. If DHCP Client is disabled, then the IP address that you specified is used.
Configuration Using the Web Interface IP Configuration Page (Continued) You can assign the subnet mask for the IP address here. If the DHCP Client function is enabled, you do not need to assign the subnet mask. The default Subnet Mask is 255.255.255.0. Subnet Mask Default Gateway Note: In the CLI, the enabled bit of the subnet mask is used to represent the number displayed in the web management interface. For example, 8 represents: 255.0.0.0,16 represents: 255.255.0.0, 24 represents: 255.255.255.0.
Configuration Using the Web Interface Time Setting Time Setting allows you to set the time manually or through a Network Time Protocol (NTP) server. NTP is used to synchronize computer clocks on the internet. You can configure NTP settings here to synchronize the clocks of several switches on the network. The ES7510-XT also provides Daylight Saving functionality. Time Setting Page Manual Setting: Click Manual Setting to change time as needed.
Configuration Using the Web Interface Switch(config)# clock timezone 01 (GMT-12:00) Eniwetok, Kwajalein 02 (GMT-11:00) Midway Island, Samoa 03 (GMT-10:00) Hawaii 04 (GMT-09:00) Alaska 05 (GMT-08:00) Pacific Time (US & Canada), Tijuana 06 (GMT-07:00) Arizona 07 (GMT-07:00) Mountain Time (US & Canada) 08 (GMT-06:00) Central America 09 (GMT-06:00) Central Time (US & Canada) 10 (GMT-06:00) Mexico City 11 (GMT-06:00) Saskatchewan 12 (GMT-05:00) Bogota, Lima, Quito 13 (GMT-05:00) Eastern Time (US & Canada) 14 (G
Configuration Using the Web Interface 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 (GMT+05:45) (GMT+06:00) (GMT+06:00) (GMT+06:00) (GMT+06:30) (GMT+07:00) (GMT+07:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+08:00) (GMT+09:00) (GMT+09:00) (GMT+09:00) (GMT+09:30) (GMT+09:30) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+10:00) (GMT+11:00) (GMT+12:00) (GMT+12:00) (GMT+13:00) 54 - Time Setting Kathmandu Almaty, Novosibirsk Astana, Dhaka Sri Jayawardenepur
Configuration Using the Web Interface DHCP Server Configuration Use this page to configure DHCP server services. DHCP Server Configuration Page DHCP Server You can select to Enable or Disable the DHCP Server function. The ES7510-XT assigns a new IP address to link partners. DHCP Server Configuration Network Enter the IPv4 address for the DHCP server. RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface DHCP Server Configuration Page (Continued) Subnet Mask Enter the subnet mask for the DHCP server. Default Gateway Enter the IP gateway address for the DHCP server. Lease Time Enter the Lease Time in seconds for the client. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 130), if you want to maintain these settings if the ES7510-XT is powered off.
Configuration Using the Web Interface DHCP Leased Entries The ES7510-XT provides an assigned IP address. DHCP Leased Entries Page Index Index of DHCP leased entries. Binding Manual or auto binding IP addresses and MAC addresses. IP Address The IP address of the leased entry. MAC Address The MAC Address of the leased entry. Lease Time(s) The lease time of the leased entry (in seconds). Reload Click to reload DHCP leased entries. RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface DHCP Relay Agent This subsection discusses the DHCP Relay Agent page. DHCP Relay Agent Page Relay Agent You can select to Enable or Disable the DHCP Relay Agent function. The ES7510-XT assigns a new IP address to link partners. Relay Policy Relay policy drop Drops the option 82 field and do not add any option 82 field. Relay policy keep Keeps the original option 82 field and forwards to server.
Configuration Using the Web Interface DHCP Relay Agent Page (Continued) DHCP Option82 Relay Agent Default: Default value of the Circuit-ID. Port: Port of the switch. Circuit ID Circuit ID: The Circuit ID includes information specific to which circuit the request came in on. It is an identifier that is specific to the relay agent, so the type of circuit varies depending on the relay agent. Default: Default value of the Remote-ID. Remote-ID IP Address: IP Address of the switch.
Configuration Using the Web Interface Backup and Restore You can use the Backup option to save the current configuration saved in the ES7510-XT flash to a PC/laptop or a TFTP server. This allows you to use the Restore option to restore a configuration file back to the ES7510-XT or load the same settings to another ES7510-XT. Before you can restore a configuration file, you must save the backup configuration file in the PC or TFTP server. The ES7510-XT then downloads this file back into the flash.
Configuration Using the Web Interface Backup the Configuration - Local File Method You can use Local File method to backup (or restore) with a Windows XP system. Note: If you have a Windows Server 2003 through Windows 7operating system, you must use the TFTP server method (Page 63). You can use PortVision DX which does not have any operating system restrictions. 1. Open the web user interface for the ES7510-XT and open the Backup and Restore page under Basic Settings. 2.
Configuration Using the Web Interface 3. Click the Folder icon, browse to the location where the backup configuration file is located., highlight the file, and click Open. 4. Click the Restore button. 5. Click Yes to the Confirm Dialog. 6. Click Ok to the Success Message. 62 - Restore the Configuration - Local Method RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Backup the Configuration - TFTP Server Method You must use a TFTP server to create or load backup files if you are using Windows Server 2003 through Windows 8.1 or PortVision DX. If you do not have a TFTP server, you can download one from Comtrol using the Start the TFTP Server subsection. Start the TFTP Server Use this procedure to download either the 32-bit or the 64-bit version from Comtrol. 1. If necessary, download the appropriate .
Configuration Using the Web Interface Restore the Configuration - TFTP Server Method To restore a configuration file, you must open a TFTP server. If necessary, use Start the TFTP Server on Page 63. The backup file must be located in the same directory that the TFTP server resides for this procedure to work. 1. Open the web user interface for the ES7510-XT, open the Backup and Restore page under Basic Settings. 2.
Configuration Using the Web Interface Upgrading Firmware (Local File) You can use this procedure to upgrade the firmware (not Bootloader) using Windows XP. Note: You can use PortVision DX to upload firmware. You must use PortVision DX or the CLI to upload Bootloader. 1. Open the web user interface for the ES7510-XT, open the Firmware Upgrade page under Basic Settings. 2. Select Local in the Firmware Upgrade drop list. 3. Click the folder icon, browse to the firmware location, highlight the .
Configuration Using the Web Interface Upgrading Firmware (TFTP Server) You can use this procedure to upgrade the firmware (not Bootloader) using a Windows operating systems. Note: You can use PortVision DX to upload firmware. You must use PortVision DX or the CLI to upload Bootloader. 1. Open a TFTP server, if necessary, see Start the TFTP Server on Page 63. 2. Place the ES7510-XT .bin file in the same directory where the TFTP server resides. 3.
Configuration Using the Web Interface Port Configuration The Port Configuration group allows you to enable/disable port state, or configure port auto-negotiation, speed, duplex, flow control, port aggregation settings (port trunking), and rate limit control. It also allows you to view port status and aggregation information.
Configuration Using the Web Interface Port Configuration Page State You can enable or disable the state of this port. Once you click Disable, the port stops to link to the other end and stops to forward any traffic. The default setting is Enable which means all the ports are workable when you receive the ES7510-XT. You can configure port speed and duplex mode of each port.
Configuration Using the Web Interface Port Status The Port Status page displays the current port status. Port Status Page Type 100BASE-TX displays for Fast Ethernet ports and 1000BASE-TX displays for Gigabit Ethernet ports Link Shows link status; Up means the link is up and Down means that the link is down. State Shows the port state. If the state is enabled it displays Enable. If the port is disabled or shutdown, it displays Disable. Speed/Duplex Current working status of the port.
Configuration Using the Web Interface Rate Control Rate limiting is a form of flow control used to enforce a strict bandwidth limit at a port. You can program separate transmit (Egress Rule) and receive (Ingress Rule) rate limits at each port, and even apply the limit to certain packet types as described below. Rate Control Page You can select the packet type that you want to filter.
Configuration Using the Web Interface Port Trunking Port Trunking allows you to group multiple Ethernet ports in parallel to increase link bandwidth. The aggregated ports can be viewed as a physical port that has a bandwidth equal to the combined bandwidth of each trunked port.The member ports of the same trunk group can balance the loading and backup for each other. The Port Trunking feature is usually used when you need higher bandwidth for the network backbone.
Configuration Using the Web Interface Aggregation Status The Port Trunk - Aggregation Information page shows the status of port aggregation. Once the aggregation ports are negotiated, you see the following status. Aggregation Status Page Group ID Displays Trunk 1 to Trunk 5 set up. Type The Type is Static or LACP. Static means that LACP is disabled and configured statically by the Administrator. Aggregated Ports When LACP links, you can see the member ports in the Aggregated column.
Configuration Using the Web Interface Power over Ethernet Power over Ethernet is one of the key features of the ES7510-XT. The ES7510-XT is IEEE 802.3af and IEEE 802.3at compliant. The ES7510-XT supports up to eight PoE injectors ports, each port with the ability to deliver 30W of power.
Configuration Using the Web Interface You can use these steps to configure PoE settings. Refer to the figure and the following table if you need more detailed information. 1. Select Enable in the PoE System drop list. 2. Select the appropriate Power Budget method. • Managed, which uses port-based rules and priorities to manage PoE output power budget • Unmanaged, which disables the rules and system controls. 3. Managed Power Budget: Enter the DC1 and DC2 power budget value. 4.
Configuration Using the Web Interface PoE Control (Continued) Voltage (V) This is the voltage applied to the power supply. Typically, you should use the same value for DC1 and DC2, otherwise the ES7510-XT draws more current from the power supply with the highest voltage. Power Budget If the power utilization is more than the warning level, the ES7510-XT sends a warning Warning Level event. The range is 0-100%. 0 is disabled.
Configuration Using the Web Interface PoE Scheduling The PoE Scheduling control is a powerful function to help you save power and money. You can schedule a PoE port after the PoE Mode has been set to Schedule in the PoE Control page. Select the port in the PoE Schedule on drop list. Click time blocks that you want to enable the PoE port and click.Apply. 76 - PoE Scheduling RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface PoE Status The PoE Status page shows the operating status of each PoE port. You can use the PoE Control page (Page 73) if you need to make any changes. RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Network Redundancy It is critical for industrial applications that the network remains running at all times. The ES7510-XT supports: • Standard Rapid Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) The ES7510-XT supports RSTP versions IEEE 802.1D-2004, IEEE 802.1D-1998 STP, and IEEE 802.1w RSTP. • Multiple Spanning Tree Protocol (MSTP) MSTP implements IEEE 802.
Configuration Using the Web Interface STP Configuration This page allows you to select the STP mode and configure the global STP/RSTP bridge configuration. Spanning Tree Protocol (STP; IEEE 802.1D) provides a loop-free topology for any LAN or bridged network. Rapid Spanning Tree Protocol (RSTP; IEEE 802.1w) is an evolution of the Spanning Tree Protocol (STP), and was introduced with the IEEE 802.1w standard, and provides faster spanning tree convergence after a topology change. In most cases, IEEE 802.
Configuration Using the Web Interface STP Port Configuration This page allows you to configure the port parameter after you have enabled STP, RSTP, or MSTP. STP Port Configuration Page You can enable/disable STP/RSTP/MSTP on a port by port basis. STP State You can disable the STP state when connecting a device in order to avoid STP waiting periods. Path Cost The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000.
Configuration Using the Web Interface STP Information The STP Information page allows you to see the ES7510-XT root information and port status. STP Information Page Root Information Root Address Root bridge address, which is the bridge with the smallest (lowest) bridge ID. Root Priority Root bridge priority, the bridge with the lowest value has the highest priority and is selected as the root. Root Port Root port of this bridge. Root Path Cost Root path cost.
Configuration Using the Web Interface STP Information Page (Continued) Port Information Port Role Descriptive information about the STP/RSTP switch port role. Role: Root, Designated, Alternate, Backup, Disabled, Unknown. Port State Descriptive information about the STP/RSTP switch port state. State: Blocking, Listening, Learning, Forwarding, Disabled, Unknown. Path Cost The cost of the path to the other bridge from this transmitting bridge at the specified port. Path cost range is 1 through 200000000.
Configuration Using the Web Interface MSTP Configuration Multiple Spanning Tree Protocol (MSTP) is a direct extension of RSTP. It can provide an independent spanning tree for different VLANs. It simplifies network management, creates a faster convergence than RSTP by limiting the size of each region, and prevents VLAN members from being segmented from the rest of the group (as sometimes occurs with IEEE 802.1D STP). While using MSTP, there are some new concepts of network architecture.
Configuration Using the Web Interface This is the MSTP Configuration page. MSTP Configuration Page MST Region Configuration Region Name A name used to identify the MST Region. Revision A value used to identify the MST Region. Apply Click the Apply button to apply the MST Region Configuration. New MST Instance Instance ID A value used to identify the MST instance, valid value are 1 through 15.
Configuration Using the Web Interface MSTP Configuration Page (Continued) Current MST Instance Configuration Instance ID A value used to identify the MST instance. Instance 0 (CIST, Common Internal Spanning Tree) is a special instance of spanning-tree known as IST or Internal Spanning Tree (=MSTI00). VLAN Group Provide a VLAN group to map this MST instance. Use the VLAN number, for example: 10. You can set a range, for example: 1-10) or set specific VLANs, for example: 2,4,6,4-7.
Configuration Using the Web Interface MSTP Port Configuration Page (Continued) Edge Port Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, and skipping the listening and learning stages. When the non-bridge device connects an edge port, this port is in a blocking state and turn to forwarding state in 2*Hello Time seconds.
Configuration Using the Web Interface MSTP Information Page Instance ID Select an instance ID to display MSTP instance information. Instance 0 (CIST, Common Internal Spanning Tree) is a special instance of spanning-tree known as IST or Internal Spanning Tree (=MSTI00). Root Information Root Address Root bridge address, which is the bridge with the smallest (lowest) bridge ID. Root Priority Root bridge priority, the bridge with the lowest value has the highest priority and is selected as the root.
Configuration Using the Web Interface Redundant Ring The most common industrial network redundancy is to form a ring or loop. Typically, managed switches are connected in series and the last switch is connected back to the first one. In such connection, you can implement Redundant Ring technology. Redundant Ring Page New Ring (Ring ID/Name) To create a Redundant Ring enter the Ring ID, which has range from 0 to 31.
Configuration Using the Web Interface Redundant Ring Page (Continued) Rapid Dual Homing Ring status Rapid Dual Homing is an important feature of Rapid Super Ring redundancy technology. When you want to connect multiple RSR or form redundant topology with other vendors, RDH allows you to have a maximum of seven multiple links for redundancy without any problem. In RDH, you do not need to configure a specific port to connect to other protocol.
Configuration Using the Web Interface Loop Protection Loop protection prevents broadcast loops in Layer 2 switching configurations. Loop Protection Page Transmit Interval Port Loop Protection Status Apply Enable/Disable All Reload 90 - Loop Protection Loop protection mechanism detection packet transmitting interval 1 ~ 10 seconds (default is 1). The port ID. Enable/Disable loop protection mechanism on port. The status of loop protection. Click Apply to apply the settings.
Configuration Using the Web Interface VLAN A Virtual LAN (VLAN) is a logical grouping of nodes for the purpose of limiting a broadcast domain to specific members of a group without physically grouping the members. The VLAN allows you to isolate network traffic so that only members of the VLAN could receive traffic from the same VLAN members.
Configuration Using the Web Interface Optionally, you can use the CLI for configuration, see VLAN (CLI) on Page 168. VLAN Port Configuration The VLAN Port Configuration page allows you to configure VLAN port parameters on a specific port. These parameters include the port VLAN ID (PVID), Tunnel Mode, Accept Frame Type and Ingress Filtering VLAN Port Configuration Page PVID Enter the port VLAN ID (PVID). The PVID allows the switches to identify which port belongs to which VLAN.
Configuration Using the Web Interface VLAN Port Configuration Page (Continued) Ingress filtering instructs the VLAN engine to filter out undesired traffic on a port. • When you Enable Ingress Filtering, the port checks whether the incoming frames belong to the VLAN they claimed or not. The port then determines if the frames can be processed or not.
Configuration Using the Web Interface VLAN Configuration Page The management VLAN ID is the VLAN ID of the CPU interface so that only member ports of the management VLAN can ping and access the switch. The default Management VLAN management VLAN ID is 1. ID Click Apply after you enter the VLAN ID. You can assign a VLAN ID and VLAN Name for the new static VLAN. Static VLAN • VLAN ID: This is used by the switch to identify different VLANs. A valid VLAN ID is between 1 and 4,094, 1 is the default VLAN.
Configuration Using the Web Interface This figure displays how to configure the Egress rule of the ports. Use the following steps to configure Egress rules: 1. Select the VLAN ID. The entry of the selected VLAN turns to light blue. 2. Assign Egress rule of the ports to U or T. 3. Press Apply to apply the setting. If you want to remove one VLAN, select the VLAN entry and then click the Remove button. RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface GVRP Configuration GARP VLAN Registration Protocol (GVRP) allows you to set-up VLANs automatically rather than manual configuration on every port on every switch in the network. GVRP conforms to the IEEE 802.1Q specification. This defines a method of tagging frames with VLAN configuration data that allows network devices to dynamically exchange VLAN configuration information with other devices.
Configuration Using the Web Interface VLAN Table This table displays the current settings of your VLAN table, including VLAN ID, Name, Status, and Egress rule of the ports. VLAN Table Page VLAN ID The ID of the VLAN. Name The name of the VLAN. Static means that this is a manually configured static VLAN. Unused means this VLAN is created by web user interface/CLI and has no member ports and the VLAN is not workable yet. Dynamic means this VLAN was learnt by GVRP. Status • -- No VLAN setting.
Configuration Using the Web Interface Private VLAN A private VLAN helps to resolve the primary VLAN ID shortage, client ports’ isolation and network security issues. The private VLAN features provides primary and secondary VLANs within a single switch. Primary VLAN: The uplink port is usually a member of the primary VLAN. A primary VLAN contains promiscuous ports that can communicate with Secondary VLANs. Secondary VLAN: The client ports are usually defined within secondary VLAN.
Configuration Using the Web Interface Private VLAN Configuration Page (Continued) Private VLAN Type • None: The VLAN is not included in private VLAN. • Primary: A primary VLAN contains promiscuous ports that can communicate with the secondary VLANs. • Isolated: The member ports of the VLAN are isolated. • Community: The member ports of the VLAN can communicate with each other. Click Apply to apply the settings.
Configuration Using the Web Interface For example: 1. VLAN Create: VLANs 2-5 are created in the VLAN Configuration page. 2. Private VLAN Type: VLANs 2-5 has their own Private VLAN Type configured in the Private VLAN Configuration page. VLAN 2 belongs to the Primary VLAN. VLANs 3-5 belong to the secondary VLAN (Isolated or Community). 3. Private VLAN Association: Associate VLANs 3-5 to VLAN 2 in the Private VLAN Association first. 4.
Configuration Using the Web Interface Traffic Prioritization Quality of Service (QoS) provides a traffic prioritization mechanism which allows you to deliver better service to certain flows. QoS can also help to alleviate congestion problems and ensure high-priority traffic is delivered first. This section allows you to configure Traffic Prioritization settings for each port with regard to setting priorities.
Configuration Using the Web Interface QoS Setting Page (Continued) Port Setting CoS The CoS column indicates that the default port priority value for untagged or prioritytagged frames. When the ES7510-XT receives the frames, the ES7510-XT attaches the value to the CoS field of the incoming VLAN-tagged packets. You can enable 0,1,2,3,4,5,6 or 7 to the port. Trust Mode indicates the Queue Mapping types that you can select.
Configuration Using the Web Interface DSCP-Queue Mapping Use this page to change DSCP values to Physical Queue mapping table. Since the switch fabric of the ES7510XT only supports four queues. Lowest, Low, Middle and High users should therefore assign how to map DSCP values to the level of the physical queue. You should therefore assign how to map DSCP value to the level of the queue. You can change the mapping table to follow the upper layer 3 switch or routers’ DSCP setting.
Configuration Using the Web Interface Multicast Filtering For multicast filtering, the ES7510-XT uses IGMP (Internet Group Management Protocol) Snooping technology. IGMP is an internet protocol that provides a way for internet device to report its multicast group membership to adjacent routers. Multicasting allows one computer on the internet to send data to a multitude of other computers that have identified themselves as being interested in receiving the originating computer’s data.
Configuration Using the Web Interface IGMP Snooping Use this page to enable the IGMP Snooping feature, assign IGMP Snooping for specific VLANs, and view the IGMP Snooping table from a dynamic learnt or static that you provide. IGMP Snooping Page You can select Enable or Disable. After enabling IGMP Snooping, you can then enable IGMP Snooping for specific VLAN. IGMP Snooping You can Enable IGMP Snooping for some VLANs so that some of the VLANs support IGMP Snooping and others do not.
Configuration Using the Web Interface IGMP Query Use this page to configure the IGMP Query feature. Since the ES7510XT can only be configured by member ports of the management VLAN, the IGMP Query can only be enabled on the management VLAN. If you want to run IGMP Snooping feature in several VLANs, first check to see whether each VLAN has its own IGMP Querier. The IGMP querier periodically sends query packets to all end-stations on the LANs or VLANs that are connected to it.
Configuration Using the Web Interface GMRP Configuration GARP Multicast Registration Protocol (GMRP) is a Generic Registration Protocol (GARP) application that provides a multicast traffic management facility at Layer 2 similar to what IGMP provides at Layer 3. GMRP and GARP are industry-standard protocols first introduced as part of IEEE 802.1D. GMRP Configuration GMRP Protocol Enable/Disable GMRP protocol. State The state of the GMRP operation on this port.
Configuration Using the Web Interface SNMP Simple Network Management Protocol (SNMP) is a protocol to exchange management information between network devices. SNMP is a member of the TCP/IP protocol suite. The ES7510-XT supports SNMP v1 and v2c and v3. An SNMP managed network consists of two main components: agents and a manager. An agent is a management software module that resides in a managed switch.
Configuration Using the Web Interface SNMP V3 Profile SNMP v3 can provide more security functions when you perform remote management through SNMP protocol. It delivers SNMP information to the administrator with user authentication; all of data between the ES7510-XT and the administrator are encrypted to ensure secure communication. SNMP V3 Profile Page User Name SNMP v3 user name. Security Level Select the following levels of security: None, Authentication, and Authentication and Privacy.
Configuration Using the Web Interface SNMP Traps SNMP Trap is the notification feature defined by SNMP protocol. All the SNMP management applications can understand such trap information. So you do not need to install new applications to read the notification information. SNMP Trap Page SNMP Trap Click Enable or Disable SNMP trap functionality. Click Apply to apply the settings. Apply Note: You must Save the settings (Page 130), if you want to maintain these settings if the ES7510-XT is powered off.
Configuration Using the Web Interface Security The ES7510-XT provides several security features for you to secure your connection. The following pages are included in this group: • Port Security on Page 111 • IP Security on Page 112 • 802.1x Configuration on Page 113 • 802.1x Port Configuration on Page 114 • 802.1x Port Status on Page 116 Optionally, you can use the CLI for configuration, see Security (CLI) on Page 182.
Configuration Using the Web Interface IP Security Use the Security IP page to set up specific IP addresses to grant authorization for management access to this ES7510-XT through a web browser or Telnet. IP Security Page IP Security Select Enable and Apply to enable the IP security function. You can assign specific IP addresses and then click Add. Only these IP addresses can access and manage Add Security IP ES7510-XT through a web browser or Telnet. The maximum security IP is 10.
Configuration Using the Web Interface 802.1x Configuration IEEE 802.1x is the protocol that performs authentication to obtain access to IEEE 802 LANs. It is port-base network access control. With the function, the ES7510-XT could control which connection is available or not. IEEE 802.1x Page System Auth Control Enable or Disable the IEEE 802.1x authentication. Authentication Method RADIUS is an authentication server that provides a key for authentication.
Configuration Using the Web Interface IEEE 802.1x Page (Continued) Shows the account information, select Remove to remove a selected account. Local RADIUS User List • User name: The user name of the local RADIUS user. • Password: The password of the local RADIUS user. • VID: The VLAN ID (VID) of the local RADIUS user. 802.
Configuration Using the Web Interface 802.1x Port Configuration Page Port control Force Authorized means that this port is authorized; the data is free to move in/out. Force unauthorized is just the opposite, the port is blocked. To control this port with a RADIUS server, select Auto for port control. Reauthentication If this field is enabled, the ES7510-XT requests the client to reauthenticate. The default time interval is 3600 seconds.
Configuration Using the Web Interface 802.1x Port Status Use the 802.1x Port Status page to observe the port status for Port Control Status, Authorize Status, Authorized Supplicant, and Oper Control Direction for each port. 116 - 802.1x Port Status RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Warning The ES7510-XT provides several types of warning features for you to remotely monitor the status of the attached devices or changes in your network. The features include System Log and SMTP Email Alert. The following web pages are included in this group: • Fault Relay • Event Selection on Page 119 • SysLog Configuration on Page 120 • SMTP Configuration on Page 121 Optionally, you can use the CLI for configuration, see Warnings (CLI) on Page 184.
Configuration Using the Web Interface Fault Relay The relay continuously opens and closes the contacts. The available range is 0-65535 seconds. Dry Output DI Note: Do not use this function with any other event. • On Period: Duration of the relay output short (closed). • Off Period: Duration of the relay output open. Relay triggered when DI changes state to high or low. Click Apply to apply the settings.
Configuration Using the Web Interface Event Selection Event Types can be divided into three basic groups: System Events, PoE Events, and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of specific ports. System Event Warning is sent when…. Device Cold Start Power is cut off and then reconnected. Device Warm Start Reboot the device by CLI or web user interface.
Configuration Using the Web Interface Port Event Warning is sent when….. Link-Up The port is connected to another device. Link-Down The port is disconnected. For example, the cable is pulled out or the opposing devices is down. Both The link status changed. PoE Powering Event Warning is sent when….. Enable The PoE port is powering. Disable The PoE port is not powering. Click Apply to apply the settings.
Configuration Using the Web Interface SMTP Configuration The ES7510-XT supports an email alert feature. The ES7510-XT sends the events that have occurred to a remote email server. The email warning conforms to the SMTP standard. The E-mail Alert page allows you to assign the SMTP Server IP, Sender E-mail, and Receiver E-mail. If the SMTP server requests authentication, you can set up the user name and password. SMTP Configuration Page SMTP Server IP Address Enter the IP address of the email server.
Configuration Using the Web Interface Monitor and Diag The ES7510-XT provides several web user interface pages for you to monitor the status of the switch or diagnostics when encountering problems related to the ES7510-XT. The features include MAC Address Table, Port Statistics, Port Mirror, Event Log, and Ping.
Configuration Using the Web Interface MAC Address Table Page Each switch fabric has a size limit to write the learnt MAC address. To save more entries for a new MAC address, the switch fabric ages out a non-used MAC address entry per the Aging Time timeout. Aging Time (Sec) This value determines the interval that an automatically learnt MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged.
Configuration Using the Web Interface Port Statistics Use this page to view operation statistics for each port. The statistics that can be viewed include Link Type, Link State, Rx Good, Rx Bad, Rx Abort, Tx Good, Tx Bad and Collisions. Note: If you see an increase of Bad, Abort or Collision counts, that may mean the network cable is not properly connected or the network performance of the port is poor.
Configuration Using the Web Interface Port Mirroring Port mirroring (also called port spanning) is a tool that allows you to mirror the traffic from one or more ports onto another port, without disrupting the flow of traffic on the original port. Any traffic that goes into or out of the Source Ports is duplicated at the Destination Ports. This traffic can then be analyzed at the Destination Port using a monitoring device or application.
Configuration Using the Web Interface Event Log The System Log feature was introduced in SysLog Configuration on Page 120. When System Log Local mode is selected, the ES7510-XT records events that occurred in the local log table. This page shows the log table. The entry includes the index, occurred data and time, and content of the events. Click Clear to clear the entries. Click Reload to refresh the table. 126 - Event Log RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Topology Discovery (LLDP) The ES7510-XT supports topology discovery or LLDP (IEEE 802.1AB Link Layer Discovery Protocol) functionality that can help to discovery multi-vendor’s network devices on the same segment by a network monitoring system (NMS) that supports LLDP functionality. With LLDP functionality, NMS can easily maintain the topology map, display port ID, port description, system description, and VLAN ID.
Configuration Using the Web Interface Ping Utility This page provides a Ping Utility to ping a remote device and check whether the device is alive or not. Type the Target IP address of the target device and click Start to start the ping. After few seconds, you can see the result in the Result field. 128 - Ping Utility RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Web Interface Device Front Panel The Device Front Panel allows you to see the LED status of the ES7510-XT.
Configuration Using the Web Interface Save to Flash The Save Configuration page saves any changes to the configuration to the flash. If the switch loses power before clicking Save Configuration causes loss of the new settings. Applying changes on web user interface pages do not save the changes to the flash. After selecting Save Configuration, click Save to Flash to save your new configuration. Optionally, you can use the CLI, see Saving to Flash (CLI) on Page 190.
Configuration Using the Command Line Interface (CLI) Overview The ES7510-XT provides in-band and out-band configuration methods: • Out-band management means that you configure the ES7510-XT using the RS-232 console cable and the Command Line Interface (CLI) to access the ES7510-XT without attaching an admin PC to the network. You can use out-band management if you lose the network connection to the ES7510-XT.
Configuration Using the Command Line Interface (CLI) Using the Serial Console Comtrol provides one RS-232 RJ45 console cable with the ES7510-XT. Note: A system COM port is required to use a serial console connection. If you do not have an available COM port, use the Using a Telnet/SSH Console procedure on Page 134. 1. Attach the RS-232 DB9 connector to your PC COM port and connect the other end to the Console port of the ES7510-XT.
Configuration Using the Command Line Interface (CLI) • HyperTerminal (Windows XP, unless installed manually) - Windows XP: Go to Start -> Program -> Accessories -> Communications -> HyperTerminal - Enter a name for the new console connection and click OK. - Enter the IP address in the Host Address text box. - Select TCP/IP (Winsock) in the Connect using drop-list and click Ok. - Set the serial settings using the Serial Settings table (above). - Press the Enter key in the Terminal window.
Configuration Using the Command Line Interface (CLI) Using a Telnet/SSH Console The ES7510-XT supports a Telnet console or SSH console with the Command Line Interface (CLI), which is the same as what you see using the RS-232 console port. The SSH connection can secure all the configuration commands you send to the ES7510-XT. SSH is a client/server architecture while the ES7510-XT is the SSH server.
Configuration Using the Command Line Interface (CLI) If you selected SSH, click Yes. • Enter the user name (default = admin). • Enter the password (default = admin). If you selected Telnet: • Enter the user name (default = admin). • Enter the password (default = admin). All the commands you see in SSH are the same as the CLI commands you see through the RS-232 console. Command Line Interface Introduction The Command Line Interface (CLI) is the user interface to the ES7510-XT embedded software.
Configuration Using the Command Line Interface (CLI) User EXEC Mode When you login to the ES7510-XT with the CLI, you are in User EXEC mode. In User EXEC mode, you can ping, telnet to a remote device, and show some basic information.
Configuration Using the Command Line Interface (CLI) 4. Type show ip route and press the Enter key to view the IP routing tables for the ES7510-XT. Switch> show ip route Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, B - BGP, > - selected route, * - FIB route S>* 0.0.0.0/0 [1/0] via 192.168.0.254, vlan1 C>* 127.0.0.0/8 is directly connected, lo C>* 192.168.0.0/16 is directly connected, vlan1 5.
Configuration Using the Command Line Interface (CLI) Privileged EXEC Mode If you type enable in User EXEC mode, you can access Privileged EXEC mode. In this mode, the ES7510-XT allows you to view current configuration, reset default, reload switch, show system information, save configuration, and enter Global Configuration mode. Type the following commands and press the Enter key: • configure terminal to access Global Configuration mode (Global Configuration Mode on Page 139). • exit to close the CLI.
Configuration Using the Command Line Interface (CLI) Global Configuration Mode If you type configure terminal in Privileged EXEC mode, you can then access Global Configuration mode. In Global Configuration mode, you can configure all ES7510-XT features. Type the following commands and press the Enter key: • interface IFNAME/VLAN, to access the corresponding Interface Configuration mode. • exit to return to Privileged EXEC mode. • ? to see the command list.
Configuration Using the Command Line Interface (CLI) (Port) Interface Configuration When you type interface IFNAME in Global Configuration mode, you can access Interface Configuration mode. In this mode you can configure port settings. The port interface names for the Fast Ethernet ports are fa1 through fa7. The port interface names for Gigabit Ethernet port are gi910. Type the interface name, for example fa1, when you want to enter certain interface configuration mode.
Configuration Using the Command Line Interface (CLI) (VLAN) Interface Configuration If you type interface VLAN VLAN-ID in Global Configuration mode, you can access VLAN Interface Configuration mode. In this mode, you can configure the settings for the specific VLAN. Switch(config)# interface vlan 1 Switch(config-if)# The VLAN interface name of VLAN 1 is VLAN 1, VLAN 2 is VLAN 2. Type exit to return to the previous mode. Type ? to see the available command list.
Configuration Using the Command Line Interface (CLI) Mode: Main Function Access and Exit Mode • VLAN Interface Configuration: Configure settings for a • specific VLAN. • Prompt Access VLAN Interface Configuration mode: Type interface VLAN VID in Global Configuration mode. Exit: Type exit or Ctrl+Z to return to Global Configuration mode. Switch(config-vlan)# Type end to return to Privileged EXEC mode. The following are useful commands to save you typing time and to avoid typing errors.
Configuration Using the Command Line Interface (CLI) VTY Configuration Locked (Error Message) An alert message appears when multiple users are attempting to configure the ES7510-XT. If the administrator is in Configuration mode, then the web users cannot change settings. The ES7510-XT allows only one administrator to configure the switch at a time. RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Command Line Interface (CLI) Basic Settings (CLI) The Basic Setting group provides you with the ability to configure switch information, IP address, User name/ Password of the system. It also allows you to do firmware upgrade, backup and restore configuration, reload factory default, and reboot the system. Optionally, you can use the web user interface for configuration, see Basic Settings on Page 48.
Configuration Using the Command Line Interface (CLI) IP Configuration IP Address/Mask (192.168.250.250, 255.255.255.0 The enabled bit of the subnet mask is used to represent the number displayed in the web user interface. For example, 8 represents: 255.0.0.0, 16 represents: 255.255.0.0, 24 represents:255.255.255.0. Switch(config)# int vlan 1 Switch(config-if)# ip address dhcp Switch(config-if)# ip address 192.168.250.
Configuration Using the Command Line Interface (CLI) Time Setting (Cont.
Configuration Using the Command Line Interface (CLI) DHCP Server (Cont.) Show DHCP server information Switch# show ip dhcp server statistics DHCP Server ON Address Pool 1 network:192.168.17.0/24 default-router:192.168.17.
Configuration Using the Command Line Interface (CLI) DHCP Server (cont.) DHCP Server Enable Switch(config-dhcp)# service dhcp DHCP Server IP Pool (Network/Mask) Switch(config-dhcp)# network A.B.C.D/M network/mask ex. 10.10.1.0/24 Switch(config-dhcp)# network 192.168.10.0/24 DHCP Server – Default Gateway Switch(config-dhcp)# default-router A.B.C.D address Switch(config-dhcp)# default-router 192.168.10.
Configuration Using the Command Line Interface (CLI) Backup and Restore Switch# copy startup-config tftp: 192.168.250.33/ default.conf Writing Configuration [OK] Backup Startup Configuration File Note: To backup the latest startup configuration file, you should save current settings to flash first. You can refer to Save to Flash on Page 130 to see how to save settings to the flash. In the example above, 192.168.250.33 is the TFTP server’s IP and default.conf is name of the configuration file.
Configuration Using the Command Line Interface (CLI) Port Configuration (CLI) The Port Configuration group allows you to enable/disable port state, or configure port auto-negotiation, speed, duplex, flow control, rate limit control, and port aggregation settings. It also allows you to view port status and aggregation information. Optionally, you can use the web user interface for configuration, see Port Configuration on Page 67.
Configuration Using the Command Line Interface (CLI) Port Control (continued) Port Control – Flow Control Port Status Switch(config-if)# flowcontrol on Flowcontrol on for port 1 set ok! Switch(config-if)# flowcontrol off Flowcontrol off for port 1 set ok! Switch# show interface fa1 Interface fastethernet1 Administrative Status : Enable Operating Status : Connected Duplex : Full Speed : 100 Flow Control :off Default Port VLAN ID: 1 Ingress Filtering : Disabled Acceptable Frame Type : All Port Security : D
Configuration Using the Command Line Interface (CLI) Port Control (continued) Switch(config-if)# rate-limit ingress mode all Limit all frames broadcast Limit Broadcast frames Rate Control flooded-unicast Limit Broadcast, Multicast and flooded unicast frames – Filter Packet Type multicast Limit Broadcast and Multicast frames Switch(config-if)# rate-limit ingress mode broadcast Set the ingress limit mode broadcast ok.
Configuration Using the Command Line Interface (CLI) Power over Ethernet (CLI) Power over Ethernet is one of the key features of ES7510-XT. It is fully IEEE 802.3af compliant, and supports IEEE 802.3at, including two-event and LLDP classification. The ES7510-XT supports up to 8Port PoE injectors in Port 1 to Port 8, each port with the ability to deliver 30W of power. For more information or to use the web user interface, see Power over Ethernet on Page 73.
Configuration Using the Command Line Interface (CLI) PoE Schedule Display Status Switch# show poe schedule [IFNAME] Inteface name Switch# show poe schedule fa1 Interface fastethernet1 PoE Schedule Status : Disabled Weekly Schedule : Sunday : All day disable Monday : 6,7,8,9,10,11,12,13,14,15,16,17,18 Tuesday : 6,7,8,9,10,11,12,13,14,15,16,17,18 Wednesday : 6,7,8,9,10,11,12,13,14,15,16,17,18 Thursday : 6,7,8,9,10,11,12,13,14,15,16,17,18 Friday : 6,7,8,9,10,11,12,13,14,15,16,17,18 Saturday : All day disabl
Configuration Using the Command Line Interface (CLI) Set PoE Powering Mode (cont.) Forced Powering Mode Switch> enable Switch# config term Switch(config)# interface fa1 Switch(config-if)# poe powering-mode forced 802.3at 2-event Switch> enable Switch# config term Switch(config)# interface fa1 Switch(config-if)# poe powering-mode 802.3at 2-event 2-event physical layer classification lldp Data link layer classification Switch(config-if)# poe powering-mode 802.3at 2-event 802.
Configuration Using the Command Line Interface (CLI) Port Type String Set Switch> enable Switch# config term Switch(config)# interface fa1 Switch(config-if)# poe type TYPE Type string, maximum 20 characters Switch> enable Switch# config term Switch(config)# interface fa1 Switch(config-if)# poe type IPCam-1 Set Port Budget Set Power Consumption (Max) to 12W Switch> enable Switch# config term Switch(config)# interface fa1 Switch(config-if)# poe budget [POWER] 0.
Configuration Using the Command Line Interface (CLI) PoE Schedule Weekday Hour Switch> enable Switch# config term Enable Hour 1, 3, 5 Switch(config)# interface fa1 and 10 to 23 on Switch(config-if)# poe schedule Sunday <0-6> Weekday: valid range 0-6 (0=Sun, 1=Mon...
Configuration Using the Command Line Interface (CLI) Network Redundancy (CLI) It is critical for industrial applications that the network remains running at all times. The ES7510-XT supports: • Standard Rapid Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) The ES7510-XT supports RSTP versions IEEE 802.1D-2004, IEEE 802.1D-1998 STP, and IEEE 802.1w RSTP. • Multiple Spanning Tree Protocol (MSTP) MSTP implements IEEE 802.
Configuration Using the Command Line Interface (CLI) GLobal (STP, RSTP, and MSTP) (Cont.
Configuration Using the Command Line Interface (CLI) MSTP (Continued) Switch(config-mst)# show current Current MST configuration Name [comtrol] Revision 65535 Instance Vlans Mapped Display Current -------- -------------------------------------0 1,4-4094 MST Configuration 1 2 2 3 -----------------------------------------------Config HMAC-MD5 Digest: 0xB41829F9030A054FB74EF7A8587FF58D ------------------------------------------------ Remove Region Name Switch(config-mst)# no name name configure revision rev
Configuration Using the Command Line Interface (CLI) MSTP (Continued) Switch(config-mst)# abort discard all mst configuration changes Switch(config)# spanning-tree mst configuration Switch(config-mst)# show pending Abort the Pending MST configuration Setting and go Name [comtrol] (->The name is not applied after Abort settings.) to the configuration Revision 65535 mode.
Configuration Using the Command Line Interface (CLI) Port Configuration Mode (Continued) Link Type – Share Switch(config-if)# spanning-tree link-type shared Edge Port Switch(config-if)# spanning-tree edge-port enable Switch(config-if)# spanning-tree edge-port disable MSTP Port Configuration Switch(config-if)# spanning-tree mst MSTMAP cost <1-200000000> the value of mst instance port cost Switch(config-if)# spanning-tree mst MSTMAP port-priority <0-240> the value of mst instance port priority in multip
Configuration Using the Command Line Interface (CLI) Global Information (cont.) Port Info Switch# show spanning-tree summary Spanning-Tree : Enabled Protocol : MSTP Root Address : 0014.7c42.3aa0 Priority : 32768 Root Path Cost : 420000 Root Port : 10 Root Times : max-age 20, hello-time 2, forward-delay 15 Bridge Address 00c0.4e38.
Configuration Using the Command Line Interface (CLI) MSTP Information (Continued) MSTP Root Information MSTP Instance Information MSTP Port Information Switch# show spanning-tree mst root MST Root Root Root Root Max Hello Fwd Instance Address Priority Cost Port age dly -------- -------------- -------- ----------- ------ ----- ----- ----MST00 00C0.4E38.0001 32768 0 N/A 20 2 15 MST01 00C0.4E38.0001 32768 0 N/A 20 2 15 MST02 00C0.4E38.
Configuration Using the Command Line Interface (CLI) Redundant Ring Switch(config)# redundant-ring 1 Ring 1 created Create or configure a Ring Switch(config-redundant-ring)# Note: 1 is the target Ring ID which is going to be created or configured.
Configuration Using the Command Line Interface (CLI) Ring Info Ring Info Switch# show redundant-ring [Ring ID] [Ring1] Ring1 Current Status : Disabled : Disabled Role Ring Status : Abnormal Ring Manager : 0000.0000.
Configuration Using the Command Line Interface (CLI) VLAN (CLI) A Virtual LAN (VLAN) is a logical grouping of nodes for the purpose of limiting a broadcast domain to specific members of a group without physically grouping the members. The VLAN allows you to isolate network traffic so that only members of the VLAN could receive traffic from the same VLAN members.
Configuration Using the Command Line Interface (CLI) VLAN Port Configuration (continued) Switch# show running-config …… ! interface ethernet1 Display – Port switchport access vlan 1 Egress Rule (Egress switchport access vlan 3 rule, IP address, switchport trunk native vlan 2 status) ……. interface vlan1 ip address 192.168.250.
Configuration Using the Command Line Interface (CLI) VLAN Configuration (continued) Display – VLAN table Switch# sh vlan VLAN Name Status Trunk Ports Access Ports ---- --------- ------------ -------------------------1 VLAN1 Static 1-,gi9-10 2 VLAN2 Unused 3 test Static fa4-8,gi9-10 fa1-3,fa7,gi9-10 Display – VLAN interface information Switch# show interface vlan1 interface vlan1 is up, line protocol detection is disabled index 14 metric 1 mtu 1500 HWaddr: 00:c0:4e:ff:01
Configuration Using the Command Line Interface (CLI) Private VLAN (CLI) A private VLAN helps to resolve the primary VLAN ID shortage, client ports’ isolation and network security issues. The Private VLAN features provides primary and secondary VLANs within a single switch. Primary VLAN: The uplink port is usually a member of the primary VLAN. A primary VLAN contains promiscuous ports that can communicate with Secondary VLANs. Secondary VLAN: The client ports are usually defined within secondary VLAN.
Configuration Using the Command Line Interface (CLI) Private VLAN Port Configuration Go to the port configuration Private VLAN Port Type Promiscuous Port Type Switch(config)# interface (port_number, ex: fa1) Switch(config-if)# switchport private-vlan host-association Set the private VLAN host association mapping map primary VLAN to secondary VLAN Switch(config-if)# switchport mode private-vlan Set private-vlan mode Switch(config-if)# switchport mode private-vlan host Set the mode to private-vlan host pro
Configuration Using the Command Line Interface (CLI) Private VLAN Information (Continued) Switch# show run Building configuration... Current configuration: hostname Switch vlan learning independent ! vlan 1 Running Config ! Information vlan 2 private-vlan primary ! vlan 3 private-vlan isolated ! vlan 4 private-vlan community ! vlan 5 private-vlan community Private VLAN Type ! ……….. ………..
Configuration Using the Command Line Interface (CLI) Private VLAN Information (Continued) PVLAN Type Switch# show vlan private-vlan type Vlan Type Ports ---- ----------------- ----------------2 primary fa3 isolated 3 fa2 4 fa1 community 5 fa4,fa5 community 10 primary - Host List Switch# show vlan Ports Mode ----- ----------normal 1 2 normal 3 normal 4 normal 5 normal 6 normal 7 host 8 host 9 host promiscuous 10 174 - Private VLAN (CLI) private-vlan port-list Vlan ---5 4 3 2 RocketLinx ES7510-XT User
Configuration Using the Command Line Interface (CLI) Traffic Prioritization (CLI) Quality of Service (QoS) provides a traffic prioritization mechanism which allows you to deliver better service to certain flows. QoS can also help to alleviate congestion problems and ensure high-priority traffic is delivered first. This section allows you to configure Traffic Prioritization settings for each port with regard to setting priorities.
Configuration Using the Command Line Interface (CLI) QoS Setting (cont.
Configuration Using the Command Line Interface (CLI) CoS-Queue Mapping (cont.) Switch# sh qos cos-map CoS to Queue Mapping : CoS Queue ---- + -----0 1 1 0 Display – CoS-Queue mapping 2 0 3 1 4 2 5 2 6 3 7 3 DSCP-Queue Mapping Switch(config)# qos dscp-map PRIORITY Assign an priority (63 highest) Switch(config)# qos dscp-map 0 Format QUEUE Assign an queue (0-3) Format: qos dscp-map priority_value queue_value. Switch(config)# qos dscp-map 0 1 Map DSCP 0 to Queue 1 The TOS/DSCP to queue mapping is set ok.
Configuration Using the Command Line Interface (CLI) Multicast Filtering (CLI) For multicast filtering, the ES7510-XT uses IGMP (Internet Group Management Protocol) Snooping technology. IGMP is an internet protocol that provides a way for internet device to report its multicast group membership to adjacent routers. Multicasting allows one computer on the internet to send data to a multitude of other computers that have identified themselves as being interested in receiving the originating computers data.
Configuration Using the Command Line Interface (CLI) IGMP Snooping (Continued) Switch# sh ip igmp interface vlan1 enabled: Yes version: IGMPv1 query-interval; 125s Display – IGMP Snooping Setting query-max-response-time: 10s Switch# sh ip igmp snooping IGMP snooping is globally enabled Vlan1 is IGMP snooping enabled Vlan2 is IGMP snooping enabled Vlan3 is IGMP snooping disabled Switch# sh ip igmp snooping multicast all VLAN IP Address Display – IGMP Table ---- --------------- 1 1 Type Ports -------
Configuration Using the Command Line Interface (CLI) IGMP Query (Continued) Switch# sh ip igmp interface vlan1 Display enabled: Yes version: IGMPv2 query-interval: 125s query-max-response-time: 10s Force Filtering Enable Disable Switch(config)# mac-address-table force filtering Filtering unknown multicast addresses ok! Switch(config)# no mac-address-table force filtering Flooding unknown multicast addresses ok! 180 - Multicast Filtering (CLI) RocketLinx ES7510-XT User Guide: 2000571 Rev.
Configuration Using the Command Line Interface (CLI) SNMP (CLI) Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. The ES7510-XT supports SNMP v1 and v2c and V3. An SNMP managed network consists of two main components: agents and a manager. An agent is a management software module that resides in a managed switch.
Configuration Using the Command Line Interface (CLI) Security (CLI) The ES7510-XT provides several security features for you to secure your connection. Optionally, you can use the web user interface for configuration, see Security on Page 111. This table provides information about the command lines for security configuration. Port Security Add MAC Port Security Switch(config)# mac-address-table static 00c0.4e38.
Configuration Using the Command Line Interface (CLI) 802.
Configuration Using the Command Line Interface (CLI) Warnings (CLI) The ES7510-XT provides several types of warning features for you to remotely monitor the status of the attached devices or changes in your network. The features include System Log and SMTP Email Alert. Optionally, you can use the web user interface for configuration, see Warning on Page 117. This table provides detailed information about the command lines of the warning configuration.
Configuration Using the Command Line Interface (CLI) Event Selection Event Selection Example: Cold Start event Example: Link Up event Display Switch(config)# warning-event coldstart Switch cold start event warmstart Switch warm start event linkdown Switch link down event linkup Switch link up event authentication Authentication failure event di Switch di event fault-relay Switch fault relay event loop-protect Switch loop protection event poe-powering Switch PoE powering or unpowered event power Switch
Configuration Using the Command Line Interface (CLI) SMTP Configuration SMTP Enable Switch(config)# smtp-server enable email-alert SMTP Email Alert set enable ok. Sender mail Switch(config)# smtp-server server 192.168.250.100 ACCOUNT SMTP server mail account, ex: admin@comtrol.com Switch(config)# smtp-server server 192.168.250.100 admin@comtrol.com SMTP Email Alert set Server: 192.168.250.100, Account: admin@comtrol.com ok. Receiver mail Switch(config)# smtp-server receipt 1 abc@comtrol.
Configuration Using the Command Line Interface (CLI) Monitor and Diag (CLI) The ES7510-XT provides several types of features for you to monitor the status of the switch or diagnostic for you to check the problem when encountering problems related to the switch. The features include MAC Address Table, Port Statistics, Port Mirror, Event Log, and Ping. Optionally, you can use the web user interface for configuration, see Monitor and Diag on Page 122.
Configuration Using the Command Line Interface (CLI) MAC Address Table (continued) Show MAC Address Table – Static MAC addresses Switch# show mac-address-table static Destination Address Address Type Vlan ------------------- --------------- ------Static 1 00c0.4e38.0101 00c0.4e38.0102 Static 1 Show Aging timeout time Switch# show mac-address-table aging-time the mac-address-table aging-time is 300 sec.
Configuration Using the Command Line Interface (CLI) Port Mirroring (continued) Display Switch# show mirror Mirror Status : Enabled Ingress Monitor Destination Port : fa6 Egress Monitor Destination Port : fa6 Ingress Source Ports :fa1,fa2, Egress Source Ports :fa1,fa2, Event Log Display Switch# <1>Jan <2>Jan <3>Jan <4>Jan show event-log 1 02:50:47 snmpd[101]: 1 02:50:50 snmpd[101]: 1 02:50:51 snmpd[101]: 1 02:50:53 snmpd[101]: Event: Event: Event: Event: Link Link Link Link 4 5 5 4 Down. Up.
Configuration Using the Command Line Interface (CLI) Saving to Flash (CLI) Save Configuration allows you to save any configuration you just made to the flash. Powering off the switch without saving the configuration causes loss of the new settings. Saving to Flash SWITCH# write Building Configuration… [OK] Save to Flash Switch# copy running-config startup-config Building Configuration...
Complete CLI List This section provides the complete listing of RocketLinx ES7510-XT commands with the supporting options: • User EXEC Mode • Privileged EXEC Mode on Page 192 • Global Configuration Mode on Page 197 • Port Interface Configuration Mode on Page 202 • VLAN Interface Configuration Mode on Page 204 User EXEC Mode For information about accessing User EXEC mode, see User EXEC Mode on Page 191. Switch> list enable exit list ping A.B.C.
Complete CLI List Privileged EXEC Mode For information about accessing Privileged EXEC mode, see Privileged EXEC Mode on Page 192.
Complete CLI List Privileged EXEC Mode (continued) dot1x reauthenticate interface IFNAME end exit hardware sensor (enable|disable) list no debug dot1x all no debug dot1x errors no debug dot1x events no debug dot1x packets no debug dot1x registry no debug dot1x state-machine no debug gmrp no debug gvrp (all|rcv|tx|gvrp_event|vlan_event) no debug ip dhcp (all|event) no debug ip dhcp snooping no debug ip igmp no debug ip igmp snooping (all|group|management|router|timer) no debug l2 mac (all|trace|debug) no de
Complete CLI List Privileged EXEC Mode (continued) show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show debugging spanning-tree deny host mac-address dot1q-tunnel dot1x dot1x all dot1x authentic-method dot1x interface IFNAME dot1x radius dot1x statistics interface IFNAME dot1x username ethertype event-
Complete CLI List Privileged EXEC Mode (continued) show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show show lldp statistics loop-protect mac-address-table mac-address-table aging-time mac-address-table dynamic mac-address-table dynamic address MACADDR mac-address-table dynamic interface IFNAME mac-address-
Complete CLI List Privileged EXEC Mode (continued) show spanning-tree active show spanning-tree interface IFNAME show spanning-tree mst show spanning-tree mst <0-15> show spanning-tree mst <0-15> interface IFNAME show spanning-tree mst configuration show spanning-tree mst interface IFNAME show spanning-tree mst root show spanning-tree summary show startup-config show system status show trunk group [1-8] show version show vlan show vlan (static|dynamic) [VLANID] show vlan VLANID show vlan management show vl
Complete CLI List Global Configuration Mode For information about accessing Global Configuration mode, see Global Configuration Mode on Page 197. Switch(config)# list administrator NAME PASSWORD arp A.B.C.D H.H.
Complete CLI List Global Configuration Mode (continued) log file FILENAME log stdout log syslog local log syslog remote A.B.C.
Complete CLI List Global Configuration Mode (continued) no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no no log syslog local log syslog remote loop-protect transmit-interval mac-address-table aging-time mac-address-table multicast MACADDR vlan VLANID mac-address-table multicast MACADDR vlan VLANID interface IFLIST mac-address-table multicast filtering mac-address-table static MACADDR vlan VLANID interfa
Complete CLI List Global Configuration Mode (continued) no vlan [VLANID] no warning-event (coldstart|warmstart) no warning-event (linkdown|linkup) [IFLIST] no warning-event authentication no warning-event di 1 no warning-event fault-relay no warning-event loop-protect no warning-event poe-powering [IFLIST] no warning-event power <1-2> no warning-event ring no warning-event sfp no warning-event time-sync no write-config (daemon|integrated) ntp peer (enable|disable) ntp peer (primary|secondary) IPADDRESS poe
Complete CLI List Global Configuration Mode (continued) snmp-server host A.B.C.D version (1|2) [COMMUNITY] snmp-server location .DWORD snmp-server name .
Complete CLI List Port Interface Configuration Mode For information about accessing Port Interface Configuration mode, see Port Interface Configuration Mode on Page 202. Switch(config)# interface fa1 Switch(config-if)# list acceptable frame type (all|vlantaggedonly) auto-negotiation description .
Complete CLI List Port Interface Mode (continued) no rate-limit ingress bandwidth no rate-limit ingress mode no shutdown no spanning-tree bpdufilter no spanning-tree bpduguard no spanning-tree cost no spanning-tree edge-port no spanning-tree link-type no spanning-tree mst MSTMAP cost no spanning-tree mst MSTMAP port-priority no spanning-tree port-priority no spanning-tree stp-state no speed no switchport access vlan VLANID no switchport block no switchport dot1q-tunnel mode (access|uplink) no switchport mo
Complete CLI List Port Interface Mode (continued) switchport switchport switchport switchport switchport switchport switchport switchport switchport switchport switchport switchport switchport access vlan remove VLANLIST block (multicast|unicast|both) dot1q-tunnel mode (access|uplink) dot1q-tunnel mode uplink add-pvid mode private-vlan host mode private-vlan promiscuous port-security private-vlan host-association <2-4094> <2-4094> private-vlan mapping <2-4094> add VLANLIST private-vlan mapping <2-4094> re
ModBus TCP /IP Support This section provides the following information: • Modbus TCP Function Codes on Page 206 • Error Checking on Page 206 • Exception Response on Page 206 • Modbus TCP Register Table on Page 207 • CLI Commands for Modbus TCP on Page 214 Overview The ES7510-XT supports Modbus TCP communications through the CLI, which does not support Modbus ASCII or Modbus RTU. This functionality is not available on a web user interface page.
ModBus TCP /IP Support through Ethernet, thus the Modbus TCP master can read or write to the Modbus registers provided by the Modbus TCP. The ES7510-XT firmware provides Modbus TCP registers that map to the ES7510-XT operating system information which, includes the description, IP address, power status, interface status, interface information and inbound/outbound packet statistics.
ModBus TCP /IP Support Code Name Descriptions 05 Acknowledge The slave has accepted the request and processing it, but a long duration of time is required to do so. 06 Slave Device Busy The slave is engaged in processing a long-duration program command. 07 Negative Acknowledge The slave cannot perform the program function received in the query. 08 Memory Parity Error The slave attempted to read extended memory, but detected a parity error in the memory.
ModBus TCP /IP Support Word Address Data Type Description Product Name = "ES7510-XT" Word 0 Hi byte = ‘E’ Word 0 Lo byte = ‘S’ Word 1 Hi byte = ‘7’ Word 1 Lo byte = ‘5’ 0x0010 16 words Word 2 Hi byte = ‘1’ Word 2 Lo byte = ‘0’ Word 3 Hi byte = ‘-’ Word 3 Lo byte = ‘X’ Word 4 Hi byte = ‘T’ Word 4 Lo byte = ‘\0’ 0x0020 0x00A0 128 words 128 words (other words = 0) SNMP system name (string) SNMP system location (string) 0x0120 128 words SNMP system contact (string) 0x01A0 32 words SNMP system OID
ModBus TCP /IP Support Word Address Data Type Description IP address For example: IP = 192.168.250.
ModBus TCP /IP Support Word Address Data Type Description DO2 0x0000:Off 0x0413 1 word 0x0414 to 0x041F 12 words 0xFFFF: unavailable Reserved address space RDY 0x0420 1 word 0x0000:Off 0x0001:On 0x0001:On RM 0x0421 1 word 0x0000:Off 0x0001:On RF 0x0422 0x0423 1 word 0x0000:Off 1 word 0x0001:On RS Port Information (32 Ports) 0x1000 to 0x11FF 16 words Port Description Administrative Status 0x1200 to 0x121F 1 word 0x0000: disable 0x0001: enable Operating Status 0x1220 to 0x123F 1 wo
ModBus TCP /IP Support Word Address Data Type Description Speed 0x0001: 10 0x0002: 100 0x0003: 1000 0x0004: 2500 0x0005: 10000 0x1260 to 0x127F 1 word 0x0101: auto 10 0x0102: auto 100 0x0103: auto 1000 0x0104: auto 2500 0x0105: auto 10000 0x0100: auto 0xFFFF: unavailable Flow Control 0x1280 to 0x129F 1 word 0x12A0 to 0x12BF 1 word 0x12C0 to 0x12DF 1 word 0x0000: off 0x0001: on 0xFFFF: unavailable Default Port VLAN ID 0x0001-0xFFFF Ingress Filtering 0x0000: disable 0x0001: enable Acceptable Fram
ModBus TCP /IP Support Word Address Data Type Description STP Status 0x0000: disabled 0x1360 to 0x137F 1 word 0x0001: blocking 0x0002: listening 0x0003: learning 0x1380 to 0x139F 1 word 0x0004: forwarding Default CoS Value for untagged packets MDIX 0x0000: disable 0x13A0 to 0x13BF 1 word 0x0001: enable 0x0002: auto 0xFFFF: unavailable Medium mode 0x0000: copper 0x13C0 to 0x13DF 1 word 0x0001: fiber 0x0002: none 0x13E0 to 0x14FF 288 words 0xFFFF: unavailable Reserved address space SFP Info
ModBus TCP /IP Support Word Address 0x21C0 to 0x21FF 0x2200 to 0x223F 0x2240 to 0x227F 0x2280 to 0x22BF 0x22C0 to 0x22FF 0x2300 to 0x233F 0x2340 to 0x237F 0x2380 to 0x23BF 0x23C0 to 0x23FF 0x2400 to 0x243F 0x2440 to 0x24FF Data Type 2 words 2 words 2 words 2 words 2 words 2 words 2 words 2 words 2 words 2 words 191 words Description Fragments Oversize Jabbers Discards Filtered frames RxError FCSError Collisions Dropped Frames Last Activated SysUpTime Reserved address space Outbound Packet Information 0x
ModBus TCP /IP Support CLI Commands for Modbus TCP The CLI commands for Modbus TCP are listed in the following table.
Technical Support Comtrol Private MIB Comtrol supports many standard MIBs for users to configure or monitor the switch configuration by SNMP. However, since some commands can’t be found in standard MIBs, Comtrol provides a Private MIB file. Compile the private MIB file with your SNMP tool. The private MIB can be downloaded it from the Comtrol FTP Site. The Private MIB tree is the same as the web tree. This is easier to understand and use.
Technical Support 216 - Comtrol Support RocketLinx ES7510-XT User Guide: 2000571 Rev.