Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
6.12.3 WPS 5GHz Wi-Fi Protected Setup (WPS) is an industry standard that simplifies wireless security setup for certified network devices. Every WPS certified device has both a PIN number and a push button, located on the device or accessed through device software. The VR-3060 has a 5GHz WPS button on the device. Devices with the WPS logo (shown here) support WPS.
IIa. PUSH-BUTTON CONFIGURATION The WPS push-button configuration provides a semi-automated configuration method. The WPS button on the front panel of the router can be used for this purpose. The WPS push-button configuration is described in the procedure below. It is assumed that the Wireless function is Enabled and that the router is configured as the Wireless Access Point (AP) of your WLAN. In addition, the wireless client must also be configured correctly and turned on, with WPS function enabled.
Enter STA PIN: a Personal Identification Number (PIN) has to be read from either a sticker or the display on the new wireless device. This PIN must then be inputted at representing the network, usually the Access Point of the network. B - For Unconfigured mode, click the Config AP button. Step 6: Activate the PIN function on the wireless client. For Configured mode, the client must be configured as an Enrollee. For Unconfigured mode, the client must be configured as the Registrar.
6.12.4 MAC Filter 5GHz This page is used to set allowed MAC addresses, and click the associated button for each interface to enable/disable the MAC address control. The current MAC control status is shown on the associated buttons. After clicking the Add button, the following screen appears. Enter the MAC address in the box provided and click Apply/Save.
.12.5 Wireless Bridge This screen allows for the configuration of wireless bridge features of the WiFi interface. See the table below for detailed explanations of the various options. Click Apply/Save to implement new configuration settings. Feature Description Bridge Restrict Selecting Disabled disables wireless bridge restriction, which means that any wireless bridge will be granted access. Selecting Enabled or Enabled (Scan) enables wireless bridge restriction.
6.12.6 Advanced 5GHz The Advanced screen allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used. Click Apply/Save to set new advanced wireless options.
Field Description Band 5GHz band is used for high speed wireless network as defined in IEEE 802.11ac Channel Drop-down menu that allows selection of a specific channel. Auto Channel Timer (min) Auto channel scan timer in minutes (0 to disable) 802.11n/EWC An equipment interoperability standard setting based on IEEE 802.11n Draft 2.0 and Enhanced Wireless Consortium (EWC) Bandwidth Select 20MHz or 40MHz or 80MHz bandwidth. To utilize maximum data throughput, select 80MHz band.
Field Description Fragmentation Threshold A threshold, specified in bytes, that determines whether packets will be fragmented and at what size. On an 802.11 WLAN, packets that exceed the fragmentation threshold are fragmented, i.e., split into, smaller units suitable for the circuit size. Packets smaller than the specified fragmentation threshold value are not fragmented. Enter a value between 256 and 2346. If you experience a high packet error rate, try to slightly increase your Fragmentation Threshold.
Field Description WMM (Wi-Fi Multimedia) The technology maintains the priority of audio, video and voice applications in a Wi-Fi network. It allows multimedia service get higher priority. WMM No Acknowledgement Refers to the acknowledge policy used at the MAC level. Enabling no Acknowledgement can result in more efficient throughput but higher error rates in a noisy Radio Frequency (RF) environment. WMM APSD This is Automatic Power Save Delivery. It saves power.
6.12.7 Basic 2.4GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. Click Apply/Save to configure the basic wireless options. Consult the table below for descriptions of these options.
Option Description Enable Wireless A checkbox that enables or disables the wireless LAN interface. When selected, a set of basic wireless options will appear. Enable Wireless Hotspot2.0 Enable Wireless Hotspot 2.0 (Wi-Fi Certified Passpoint) on the wireless interface. Hide Access Point Select Hide Access Point to protect the access point from detection by wireless active scans. If the access point is hidden, it will not be listed or listed with empty SSID in the scan result of wireless stations.
6.12.8 Security 2.4GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Please see 6.12.9 for WPS setup instructions. Click Apply/Save to implement new configuration settings. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below). Select SSID Select the wireless network name from the drop-down menu.
Different authentication type pops up different settings requests. Choosing 802.1X, enter RADIUS Server IP address, RADIUS Port, RADIUS key and Current Network Key. Also, enable WEP Encryption and select Encryption Strength. Select the Current Network Key and enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys and enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys. Choosing WPA2-PSK, you must enter WPA Pre-Shared Key and Group Rekey Interval.
Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
6.12.9 WPS 2.4GHz Wi-Fi Protected Setup (WPS) is an industry standard that simplifies wireless security setup for certified network devices. Every WPS certified device has both a PIN number and a push button, located on the device or accessed through device software. The VR-3060 has a 2.4GHz WPS button on the device. Devices with the WPS logo (shown here) support WPS.
IIa. PUSH-BUTTON CONFIGURATION The WPS push-button configuration provides a semi-automated configuration method. The WPS button on the front panel of the router can be used for this purpose. The WPS push-button configuration is described in the procedure below. It is assumed that the Wireless function is Enabled and that the router is configured as the Wireless Access Point (AP) of your WLAN. In addition, the wireless client must also be configured correctly and turned on, with WPS function enabled.
Enter STA PIN: a Personal Identification Number (PIN) has to be read from either a sticker or the display on the new wireless device. This PIN must then be inputted at representing the network, usually the Access Point of the network. B - For Unconfigured mode, click the Config AP button. Step 6: Activate the PIN function on the wireless client. For Configured mode, the client must be configured as an Enrollee. For Unconfigured mode, the client must be configured as the Registrar.
6.12.10 MAC Filter 2.4GHz This option allows access to the router to be restricted based upon MAC addresses. To add a MAC Address filter, click the Add button shown below. To delete a filter, select it from the MAC Address table below and click the Remove button. Option Select SSID Description Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN.
Enter the MAC address in the box provided and click Apply/Save.
6.12.11 Wireless Bridge 2.4GHz This screen allows for the configuration of wireless bridge features of the WiFi interface. See the table below for detailed explanations of the various options. Click Apply/Save to implement new configuration settings. Feature Description Bridge Restrict Selecting Disabled disables wireless bridge restriction, which means that any wireless bridge will be granted access. Selecting Enabled or Enabled (Scan) enables wireless bridge restriction.
6.12.12 Advanced 2.4GHz The Advanced screen allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used. Click Apply/Save to set new advanced wireless options.
Field Description Channel Drop-down menu that allows selection of a specific channel. Auto Channel Timer (min) Auto channel scan timer in minutes (0 to disable) 802.11n/EWC An equipment interoperability standard setting based on IEEE 802.11n Draft 2.0 and Enhanced Wireless Consortium (EWC) Bandwidth Select 20MHz or 40MHz bandwidth. 40MHz bandwidth uses two adjacent 20MHz bands for increased data throughput. Control Sideband Select Upper or Lower sideband when in 40MHz mode. 802.
Field Description RTS Threshold Request to Send, when set in bytes, specifies the packet size beyond which the WLAN Card invokes its RTS/CTS mechanism. Packets that exceed the specified RTS threshold trigger the RTS/CTS mechanism. The NIC transmits smaller packet without using RTS/CTS. The default setting of 2347 (maximum length) disables RTS Threshold. DTIM Interval Delivery Traffic Indication Message (DTIM) is also known as Beacon Rate. The entry range is a value between 1 and 65535.
Chapter 7 Diagnostics You can reach this page by clicking on the following icon located at the top of the screen. 7.1 Diagnostics – Individual Tests The first Diagnostics screen is a dashboard that shows overall connection status. Click the Diagnostics Menu item on the left side of the screen to display the individual connections.
7.2 Ethernet OAM The Ethernet OAM (Operations, Administration, Management) page provides settings to enable/disable 802.3ah, 802.1ag/Y1.731 OAM protocols. To enable Ethernet Link OAM (802.3 ah), click Enabled to display the full configuration list. At least one option must be enabled for 802.1ah.
To enable Ethernet Service OAM (802.1ag/Y1731), click Enabled to display the full configuration list. Click Apply/Save to implement new configuration settings.
7.3 Uptime Status This page shows System, DSL, ETH and Layer 3 uptime. If the DSL line, ETH or Layer 3 connection is down, the uptime will stop incrementing. If the service is restored, the counter will reset and start from 0. A Bridge interface will follow the DSL or ETH timer. The "ClearAll" button will restart the counters from 0 or show "Not Connected" if the interface is down.
7.4 Ping Input the IP address/hostname and click the Ping button to execute ping diagnostic test to send the ICMP request to the specified host.
7.5 Trace Route Input the IP address/hostname and click the TraceRoute button to execute the trace route diagnostic test to send the ICMP packets to the specified host.
Chapter 8 Management You can reach this page by clicking on the following icon located at the top of the screen. The Management menu has the following maintenance functions and processes: 8.1 Settings This includes Backup Settings, Update Settings, and Restore Default screens. 8.1.1 Backup Settings To save the current configuration to a file on your PC, click Backup Settings. You will be prompted for backup file location.
8.1.2 Update Settings This option recovers configuration files previously saved using Backup Settings. Enter the file name (including folder path) in the Settings File Name box, or press Browse… to search for the file, then click Update Settings to recover settings. 8.1.3 Restore Default Click Restore Default Settings to restore factory default settings. After Restore Default Settings is clicked, the following screen appears. Close the browser and wait for 2 minutes before reopening it.
NOTE: This entry has the same effect as the Reset button. The VR-3060 board hardware and the boot loader support the reset to default. If the Reset button is continuously pressed for more than 10 seconds, the current configuration data will be erased. If the Reset button is continuously pressed for more than 60 seconds, the boot loader will erase all configuration data saved in flash memory and enter bootloader mode.
8.2 System Log This function allows a system log to be kept and viewed upon request. Follow the steps below to configure, enable, and view the system log. STEP 1: Click Configure System Log, as shown below (circled in Red). STEP 2: Select desired options and click Apply/Save. Consult the table below for detailed descriptions of each system log option. Option Description Log Indicates whether the system is currently recording events. The user can enable or disable event logging.
Option Description Log Level Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the VR-3060 SDRAM. When the log buffer is full, the newer event will wrap up to the top of the log buffer and overwrite the old event. By default, the log level is “Debugging”, which is the lowest critical level.
8.3 SNMP Agent Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device. Select the Enable radio button, configure options, and click Save/Apply to activate SNMP.
8.4 TR-069 Client WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Select desired values and click Apply/Save to configure TR-069 client options. The table below is provided for ease of reference. Option Description Enable TR-069 Tick the checkbox OUI-serial The serial number used to identify the CPE when making a connection to the ACS using the CPE WAN Management Protocol.
Option Description ACS User Name Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE. ACS Password Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE. WAN Interface used by TR-069 client Choose Any_WAN, LAN, Loopback or a configured connection.
8.5 Internet Time This option automatically synchronizes the router time with Internet timeservers. To enable time synchronization, tick the corresponding checkbox , choose your preferred time server(s), select the correct time zone offset, and click Apply/Save. NOTE: Internet Time must be activated to use. See 5.5 Parental Control. The Internet time feature will not operate when the router is in bridged mode, since the router would not be able to connect to the NTP timeserver.
8.6 Access Control 8.6.1 Accounts This screen is used to configure the user account access passwords for the device. Access to the VR-3060 is controlled through the following user accounts: • The root account has unrestricted access to view and change the configuration of your Broadband router. • The support account is typically utilized by Carrier/ISP technicians for maintenance and diagnostics.
Note: Passwords may be as long as 16 characters but must not contain a space. Click Save/Apply to continue.
8.6.2 Services The Services option limits or opens the access services over the LAN or WAN. The access services available are: HTTP, SSH, TELNET, SNMP, HTTPS, FTP, TFTP and ICMP. Enable a service by selecting its dropdown listbox. Click Apply/Save to activate.
8.6.3 IP Address The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets. The services are the system applications listed in the Service Control List beside ICMP. Click the Add button to display the following.
8.7 Wake-on-LAN This tool allows you to wake up (power on) computers connected to the Broadband Router LAN interface by sending special "magic packets". The network interface card in the computer or device that is going to be woken up must support Wake-on-LAN. LAN Interface – Select the LAN interface to send the Wake-on-LAN packet. MAC Address – Specify the MAC address of the device that is going to be woken up.
8.8 Update Software This option allows for firmware upgrades from a locally stored file. STEP 1: Obtain an updated software image file from your ISP. STEP 2: Select the configuration from the drop-down menu. Configuration options: No change – upgrade software directly. Erase current config – If the router has save_default configuration, this option will erase the current configuration and restore to save_default configuration after software upgrade.
8.9 Reboot To save the current configuration and reboot the router, click Reboot. NOTE: You may need to close the browser window and wait for 2 minutes before reopening it. It may also be necessary, to reset your PC IP configuration.
Chapter 9 Logout To log out from the device simply click the following icon located at the top of your screen. When the following window pops up, click the OK button to exit the router. Upon successful exit, the following message will be displayed.
Appendix A - Firewall STATEFUL PACKET INSPECTION Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. DENIAL OF SERVICE ATTACK Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
Example 1: Filter Name Protocol Policy Source IP Address Source Subnet Mask Source Port Dest. IP Address Dest. Subnet Mask Dest. Port Selected WAN interface : : : : : : : : : : In_Filter1 TCP Allow 210.168.219.45 255.255.0.0 80 NA NA NA br0 This filter will ACCEPT all TCP packets coming from WAN interface “br0” with IP Address/Subnet Mask 210.168.219.45/16 with a source port of 80, irrespective of the destination. All other incoming packets on this interface are DROPPED.
DAYTIME PARENTAL CONTROL This feature restricts access of a selected LAN device to an outside Network through the VR-3060, as per chosen days of the week and the chosen times. Example: User Name : Browser's MAC Address : Days of the Week : Start Blocking Time : End Blocking Time : FilterJohn 00:25:46:78:63:21 Mon, Wed, Fri 14:00 18:00 With this rule, a LAN device with MAC Address of 00:25:46:78:63:21 will have no access to the WAN on Mondays, Wednesdays, and Fridays, from 2pm to 6pm.
Appendix B - Pin Assignments Giga ETHERNET Ports (RJ45) Pin Name Description 1 BI_DA+ Bi-directional pair A + 2 BI_DA- Bi-directional pair A - 3 BI_DB+ Bi-directional pair B + 4 BI_DC+ Bi-directional pair C + 5 BI_DC- Bi-directional pair C - 6 BI_DB- Bi-directional pair B - 7 BI_DD+ Bi-directional pair D + 8 BI_DD- Bi-directional pair D - 171
Appendix C – Specifications Hardware Interface RJ-11 X 1 for ADSL2+/VDSL2, RJ-45 X 4 for LAN, RJ-45 X 1 for WAN, Reset Button X 1, WPS/WiFi on/off button x2, Internal Wi-Fi Antennas X 2, External Wi-Fi Antennas X 2, Power Switch X 1, USB 3.0 Host X 1 WAN Interface Comply with ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2, AnnexM ADSL2+ Downstream: 24 Mbps Upstream: 1.3 Mbps Comply with G.993.
Bridge Functions Transparent bridging .............................. Yes VLAN support ....................................... Yes Spanning Tree Algorithm ........................ Yes IGMP Proxy ..........................................
Appendix D - SSH Client Unlike Microsoft Windows, Linux OS has a ssh client included. For Windows users, there is a public domain one called “putty” that can be downloaded from here: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the ssh client you must first enable SSH access for the LAN or WAN from the Management Access Control Services menu in the web user interface. To access the router using the Linux ssh client For LAN access, type: ssh -l root 192.168.1.
Appendix E - Printer Server These steps explain the procedure for enabling the Printer Server. NOTE: This function only applies to models with a USB host port. STEP 1: Enable Print Server from Web User Interface. Select Enable on-board print server checkbox and enter Printer name and Make and model. Click the Apply/Save button. NOTE: The Printer name can be any text string up to 40 characters. The Make and model can be any text string up to 128 characters.
STEP 3: Click Next to continue when you see the dialog box below. STEP 4: Select Network Printer and click Next.
STEP 5: Select Connect to a printer on the Internet and enter your printer link. (e.g. http://192.168.1.1:631/printers/hp3845) and click Next. NOTE: The printer name must be the same name entered in the ADSL modem WEB UI “printer server setting” as in step 1. STEP 6: Click Have Disk and insert the printer driver CD.
STEP 7: Select driver file directory on CD-ROM and click OK. STEP 8: Once the printer name appears, click OK.
STEP 9: Choose Yes or No for default printer setting and click Next. STEP 10: Click Finish.
STEP 11: Check the status of printer from Windows Control Panel, printer window. Status should show as Ready.
Appendix F - Connection Setup Creating a WAN connection is a two-stage process. 1 - Setup a Layer 2 Interface (ATM, PTM or Ethernet). 2 - Add a WAN connection to the Layer 2 Interface. The following sections describe each stage in turn. F1 ~ Layer 2 Interfaces Every layer2 interface operates in Multi-Service Connection (VLAN MUX) mode, which supports multiple connections over a single interface. Note that PPPoA and IPoA connection types are not supported for Ethernet WAN interfaces.
Heading Description Interface WAN interface name VPI ATM VPI (0-255) VCI ATM VCI (32-65535) DSL Latency {Path0} portID = 0 {Path1} port ID = 1 {Path0&1} port ID = 4 Category ATM service category Peak Cell Rate Maximum allowed traffic rate for the ATM PCR service connection Sustainable Cell Rate The average allowable, long-term cell transfer rate on the VBR service connection Max Burst Size The maximum allowable burst size of cells that can be transmitted continuously on the VBR service conn
There are many settings here including: VPI/VCI, DSL Link Type, Encapsulation Mode, Service Category and Queue Weight. Here are the available encapsulations for each xDSL Link Type: EoA- LLC/SNAP-BRIDGING, VC/MUX PPPoA- VC/MUX, LLC/ENCAPSULATION IPoA- LLC/SNAP-ROUTING, VC MUX STEP 3: Click Apply/Save to confirm your choices. On the next screen, check that the ATM interface is added to the list. For example, an ATM interface on PVC 0/35 in Default Mode with an EoA Link type is shown below.
To add a WAN connection go to Section F2 ~ WAN Connections. F1.2 PTM Interfaces Follow these procedures to configure a PTM interface. NOTE: The VR-3060 supports up to four PTM interfaces. STEP 1: Go to Basic Setup the drop-down menu. WAN Setup This table is provided here for ease of reference. Heading Description Interface WAN interface name.
Heading Description DSL Latency {Path0} portID = 0 {Path1} port ID = 1 {Path0&1} port ID = 4 PTM Priority Normal or High Priority (Preemption). Connection Mode Default Mode – Single service over one interface. Vlan Mux Mode – Multiple Vlan services over one interface. IP QoS Quality of Service (QoS) status. Remove Select interfaces to remove. STEP 2: Click Add to proceed to the next screen.
F1.3 Ethernet WAN Interface The VR-3060 supports a single Ethernet WAN interface over the ETH WAN port. Follow these procedures to configure an Ethernet interface. STEP 1: Go to Basic Setup from the drop-down menu. WAN Setup Select ETHERNET Interface This table is provided here for ease of reference. Heading Description Interface/ (Name) WAN interface name. Connection Mode Default Mode – Single service over one interface. Vlan Mux Mode – Multiple Vlan services over one interface.
STEP 3: Select an Ethernet port and Click Apply/Save to confirm your choices. On the next screen, check that the ETHERNET interface is added to the list. To add a WAN connection go to Section F2 ~ WAN Connections.
F2 ~ WAN Connections The VR-3060 supports one WAN connection for each interface, up to a maximum of 16 connections. To setup a WAN connection follow these instructions. STEP 1: Go to Basic Setup WAN Setup. STEP 2: Click Add to create a WAN connection. The following screen will display. STEP 3: Choose a layer 2 interface from the drop-down box and click Next. The WAN Service Configuration screen will display as shown below.
NOTE: The WAN services shown here are those supported by the layer 2 interface you selected in the previous step. If you wish to change your selection click the Back button and select a different layer 2 interface. STEP 4: For VLAN Mux Connections only, you must enter Priority & VLAN ID tags. Select a TPID if VLAN tag Q-in-Q is used. STEP 5: You will now follow the instructions specific to the WAN service type you wish to establish.
F2.1 PPP over ETHERNET (PPPoE) STEP 1: Select the PPP over Ethernet radio button and click Next. You can also enable IPv6 by selecting from the drop-down box at the bottom of this screen. STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
Click Next to continue or click Back to return to the previous step. The settings shown above are described below. PPP SETTINGS The PPP Username, PPP password and the PPPoE Service Name entries are dependent on the particular requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. For Authentication Method, choose from AUTO, PAP, CHAP, and MSCHAP.
ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port. An external host can send a packet to the internal host, by sending a packet to the mapped external address. DIAL ON DEMAND The VR-3060 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox .
ENABLE PPP DEBUG MODE When this option is selected, the system will put more PPP connection information into the system log. This is for debugging errors and not for normal usage. BRIDGE PPPOE FRAMES BETWEEN WAN AND LOCAL PORTS (This option is hidden when PPP IP Extension is enabled) When Enabled, this creates local PPPoE connections to the WAN side. Enable this option only if all LAN-side devices are running PPPoE clients, otherwise disable it.
STEP 4: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Click Next to continue or click Back to return to the previous step.
STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
F2.2 IP over ETHERNET (IPoE) STEP 1: *Select the IP over Ethernet radio button and click Next. * For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID.
STEP 2: The WAN IP settings screen provides access to the DHCP server settings. You can select the Obtain an IP address automatically radio button to enable DHCP (use the DHCP Options only if necessary). However, if you prefer, you can use the Static IP address method instead to assign WAN IP address, Subnet Mask and Default Gateway manually. NOTE: If IPv6 networking is enabled, an additional set of instructions, radio buttons, and text entry boxes will appear at the bottom of the screen.
STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step. ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox . The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e.
STEP 4: To choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step.
STEP 5: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Click Next to continue or click Back to return to the previous step.
STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
F2.3 Bridging STEP 1: *Select the Bridging radio button and click Next. Allow as IGMP Multicast Source Click to allow use of this bridge WAN interface as IGMP multicast source. Allow as MLD Multicast Source Click to allow use of this bridge WAN interface as MLD multicast source. * For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID. For VLAN tag Q-in-Q service, select the TPID from the list.
STEP 2: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to return to the previous screen. After clicking Apply/Save, the new service should appear on the main screen. NOTE: If this bridge connection is your only WAN service, the VR-3060 will be inaccessible for remote management or technical support from the WAN.
F2.4 PPP over ATM (PPPoA) STEP 1: Click Next to continue.
STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step. PPP SETTINGS The PPP username and password are dependent on the requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. (Authentication Method: AUTO, PAP, CHAP, or MSCHAP.
ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port. An external host can send a packet to the internal host, by sending a packet to the mapped external address. DIAL ON DEMAND The VR-3060 can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox .
ENABLE PPP DEBUG MODE When this option is selected, the system will put more PPP connection information into the system log. This is for debugging errors and not for normal usage. ENABLE IGMP MULTICAST PROXY Tick the checkbox to enable Internet Group Membership Protocol (IGMP) multicast. This protocol is used by IPv4 hosts to report their multicast group memberships to any neighboring multicast routers. Enable IGMP Multicast Source Enable the WAN interface to be used as IGMP multicast source.
STEP 4: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Click Next to continue or click Back to return to the previous step.
STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
F2.5 IP over ATM (IPoA) STEP 1: Click Next to continue. STEP 2: Enter the WAN IP settings provided by your ISP. Click Next to continue. STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step.
ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox . The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox should not be selected, so as to free up system resources for improved performance. ENABLE FULLCONE NAT This option becomes available when NAT is enabled.
NOTE: If the DHCP server is not enabled on another WAN interface then the following notification will be shown before the next screen. STEP 5: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Click Next to continue or click Back to return to the previous step.
STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen.
