User Manual

ManualsBrandsComtrend ManualsElectronicsWireless Extender

Introduction

This Quick Installation Guide will help you to quickly and easily install

your Wireless Extender units by performing the few simple steps

described below. Before you begin, check that you have:

• One WAP-5834 Access Point unit (An “AP” is stated in chassis

label)

• One WAP-5834 Client unit (A “Client” is stated in chassis label)

• Two CAT5 ETHERNET cables

• Two power adapters

• One Quick Installation Guide

Easy Link

Step 1 - Power connection

Plug in the power adapter included in your package, and connect

it to the WAP-5834 AP and Client device.

QUICK

INSTALLATION

GUIDE

WAP-5834

Wireless Extender

BeamLink 5834, CT-5834, 5834, WL5538AP,

Summary of content (9 pages)

PAGE 1
BeamLink 5834, CT-5834, 5834, WL5538AP, WAP-5834 Wireless Extender QUICK INSTALLATION GUIDE Introduction This Quick Installation Guide will help you to quickly and easily install your Wireless Extender units by performing the few simple steps described below.
PAGE 2
LAN RESET DC-IN Using a power supply with different voltage rating than the one included with the WAP-5834 device may cause damage and void the warranty for this product. Step 2 - Placement and connections The WAP-5834 AP and Client device in your package are pre-configured to work together. Place the WAP-5834 AP device on an easily accessible surface near the Home Gateway or Cable/DSL Modem. A.
PAGE 3
Wireless Make sure that the LAN LED on the WAP-5834 AP is flashing blue. WPS LAN Power Place the WAP-5834 Client device on an easily accessible surface near the set top box. B. Plug one end of the Ethernet cable into the LAN port of the set top box device and the other end into the Ethernet port of the WAP-5834 Client. LAN RESET DC-IN IR STB-7 007 S TU STA N A W Set Top Box Make sure that the LAN LED on the WAP-5834 Client is flashing blue.
PAGE 4
Congratulations! You have finished installing your new Wireless Extender devices. To test your connectivity, turn on the TV and set top box, then watch any available TV channel. Pairing The WAP-5834 AP and Client device in your package are pre-configured to work together. To add additional WAP-5834 Clients you will need to perform the pairing procedures as explained below. Place the WAP-5834 Client device between 1 to 3 meters from the WAP-5834 AP device. Step 1.
PAGE 5
Step 2. Wait for the pairing process to complete by watching the LEDs on the devices: The LEDs will flash blue for WPS a few seconds. After successful pairing the WPS LEDs will change to solid blue, and after two minutes turn off. The Wireless WPS LEDs will then be solid blue. Wireless If pairing is unsuccessful, the LED will flash blue for two WPS minutes.
PAGE 6
Advanced Setting The instructions below are for users who have a basic Network knowledge. Users are not encouraged to configure the following settings because this may cause irreversible damage. Change AP or Client mode This is to enable users to change WAP-5834 to AP or Client in a real situation. Note: • If you are connecting to the WAP-5834 directly from a PC, be sure to set a static IP in the same range as the AP or Client unit (e.g. 10.0.0.25) to access the Web Configuration page.
PAGE 7
Advanced Troubleshooting • The WPS function is not working Make sure that: • The WPS function is activated in the AP device. a. Enter into WAP-5834 AP Web GUI through browsers such as IE by default IP address 10.0.0.2. b. Type default username and password: root/12345 c. Change the security mode to WPA2-PSK in Security Settings by selecting it in the drop-down menu.
PAGE 8
d. Enable WPS in WPS setting and press the “Apply” button. • Complete the pairing procedures as described in the Pairing section. • The Wireless LED is not on • Make sure that you have completed a successful pairing procedure as described in the Pairing section. FOR MORE HELP: If you have further questions or require personal assistance, please contact your equipment provider.
PAGE 9
This equipment also should be installed and operated with minimum distance 20cm between the radiator & your body. This device within the 5.15~5.25 GHz band is restricted to indoor operations to reduce any potential for harmful interference to cochannel MSS operations. The range of product's temperture is -20℃ to 50℃ that can keep normal operating function, and it won't affect to frequency stability.