NexusLink 5700 Wireless ADSL bonding IAD User’s Manual Version C1.
Warning Before servicing or disassembling this equipment, always disconnect all power and telephone lines from the device. Use an appropriate power supply and a UL Listed telephone line cord. Specification of the power supply is clearly stated in Appendix C. Preface This manual provides information to network administrators. It covers the installation, operation and applications of the Wireless ADSL bonding IAD.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter.
Table of Contents CHAPTER 1 INTRODUCTION ....................................................................................................6 1.1 FEATURES ........................................................................................................................................6 1.2 APPLICATION ...................................................................................................................................7 1.3 FRONT PANEL LED INDICATORS ....................................
7.1 STATUS ..........................................................................................................................................53 7.2 SIP ................................................................................................................................................53 7.2.1 Global Parameters .......................................................................................................54 7.2.2 Service Provider.....................................................
APPENDIX A: FIREWALL ................................................................................................................85 APPENDIX B: PIN ASSIGNMENTS.................................................................................................89 APPENDIX C: SPECIFICATIONS....................................................................................................90 APPENDIX D: SSH CLIENT .................................................................................................
Chapter 1 Introduction The NexusLink 5700 Wireless ADSL bonding IAD features flexible networking connectivity with dual ADSL line capability, four 10/100 Ethernet ports, and an 802.11g wireless LAN access point. It has robust routing capabilities to segment and direct data streams and allows for multiple data encapsulations. The NexusLink 5700 is a black box solution for deploying Triple Play architectures, doubling bandwidth (48Mbps) performance over traditional ADSL2 modems.
1.2 Application This diagram depicts the application of the NexusLink 5700 on a wireless network.
1.3 Front Panel LED Indicators The front panel LED indicators are shown in the picture below, followed by an explanation in the table below. LED POWER Color Mode Function Green On The router is powered up. Off The router is powered down. On An Ethernet Link is established. Off An Ethernet Link is not established. Green LAN 1X~4X Green Blink Data transmitting or receiving over LAN.
Chapter 2 Installation 2.1 Hardware Installation Follow the instructions below to complete the hardware installation. A schematic of the back of the router is shown below for reference. Reset button Connection to Power Connect the power jack to the shipped power cord. Attach the power adapter to the wall outlet or other AC source. After all connections have been made the router will perform a self-test. Wait a few moments and the router will be ready to operate.
Chapter 3 Login via Web Browser This section describes how to manage the router via a web browser. The web page is best viewed with Microsoft Internet Explorer 5.0 and later. Access Code Required: #0009@3BFA. The user can change the Access Code later (see 9.5 Password). 3.1 IP Address The default IP address of the router (LAN port) is 192.168.1.254 To configure the router for the first time, the configuration PC must have a static IP address within the 192.168.1.x subnet.
3.2 Login Procedure Perform the following steps to bring up the web browser and configure the router. STEP 1: Start the Internet browser. Type the IP address for the router in the Web address field. For example, if the IP address is 192.168.1.254, type http://192.168.1.
Chapter 4 Device Select the Device button from the main menu to display the Device Summary information as here.
4.1 Device Summary The main menu has several options, and selecting each of these options opens a submenu with more selections. Subsequent sections will introduce the other main menu options in sequence. The Device Summary screen will display at startup.
4.2 Reset Statistics To reset all statistics including LAN, WAN and xDSL click Reset Statistics. When the following window is displayed, simply click the Reset Statistics button to confirm your choice.
4.3 Troubleshoot Your device is capable of testing your DSL connection. Click Troubleshoot and the diagnostics window will display. The Diagnostics menu provides feedback on the connection status of the device and the ADSL link. Click Troubleshoot to bring up the following window. The individual test results are explained below.
Test Description Ethernet Connection Pass: indicates that the Ethernet interface from your computer is connected to the LAN port of your DSL router. A flashing or solid green LAN LED on the router also signifies that an Ethernet connection is present and that this test is successful. Fail: Indicates that the DSL router does not detect the Ethernet interface on your computer. Wireless Connection Pass: Indicates that the Wireless interface from your computer is connected to the wireless network.
4.4 Wireless This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. Click Wireless to bring up the following window. Input the access code (which is located ______) and click the 17 button.
The options shown here allow you to configure security features of the wireless LAN interface.
4.4.1 Enable Wireless Option Description Enable Wireless A checkbox that enables or disables the wireless LAN interface. When selected, the Web UI displays Hide Access point, SSID, and County settings. The default is Enable Wireless. 4.4.2 Wireless - Security Configure Wireless security settings can be configured according to Wi-Fi Protected Setup (WPS) or Manual Setup. The WPS method configures security settings automatically (see 4.4.
The settings for WPA authentication are shown below. The settings for WPA-PSK authentication are shown next. WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key.
Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
4.4.3 WPS Setup Wi-Fi Protected Setup (WPS) is an industry standard that simplifies wireless security setup for certified network devices. Every WPS certified device has both a PIN number and a push button, located on the device or accessed through device software. The NexusLink 5700 has both a WPS button on the device and a virtual button accessible from the web user interface (WUI). To configure security settings with WPS, follow the procedures below.
Step 2: Set the WPS AP Mode. Configured is used when the NexusLink 5700. will assign security settings to clients. Unconfigured is used when an external client assigns security settings to the NexusLink 5700. NOTES: Your client may or may not have the ability to provide security settings to the NexusLink 5700. If it does not, then you must set the WPS AP mode to Configured. Consult the device documentation to check its capabilities.
will see the following dialog box if the Key is too short or too long. Step 5: Click the IIIa. button at the bottom of the window. PUSH-BUTTON CONFIGURATION The WPS push-button configuration provides a virtual button (accessible from the web user interface) configuration method. The WPS push-button configuration is described in the procedure below. It is assumed that the Wireless function is Enabled and that the router is configured as the Wireless Access Point (AP) of your WLAN.
Now go to Step 8 (part IV. Check Connection) to check the WPS connection. IIIb. WPS – PIN CONFIGURATION Using this method, security settings are configured with a personal identification number (PIN). The PIN can be found on the device itself or within the software. The PIN may be generated randomly in the latter case. To obtain a PIN number for your client, check the device documentation for specific instructions. The WPS PIN configuration is described in the procedure below.
Step 7: Activate the PIN function on the wireless client. For Configured mode, the client must be configured as an Enrollee. For Unconfigured mode, the client must be configured as the Registrar. This is different from the External Registrar function provided in Windows Vista. The figure below provides an example of a WPS client PIN function in-progress. Now go to Step 8 (part IV. Check Connection) to check the WPS connection. IV.
4.5 Restart Your System Should you want to reboot the NexusLink 5700, please follow the instructions provided below.
Click Restart your System to bring up the following window. When the following window is displayed, simply click the Reboot button to confirm your choice. The following window will display.
4.6 Home Network Click Home Network to bring up the following window.
Heading Description Interface LAN interface(s) Received/Transmitted: Click the - Bytes Number of Bytes - Pkts Number of Packets - Errs Number of packets with errors - Drops Number of dropped packets button to refresh this screen.
4.7 Gaming and Applications This window allows you to modify your firewall settings. Click Gaming and Applications to bring up the following window.
4.7.1 Incoming Traffic Control IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. The default setting for all Incoming traffic is Blocked. To add or remove IP filters, Click Input the access code (which is located ______) and click the button.
Filter Name Type a name for the filter rule. Rule Order Execute IP Filter order. (Available in future versions). IP Version IPv4 selected by default. Protocol User can select: TCP, TCP/UDP, UDP or ICMP. Source IP address Input source IP address. Source Subnet Mask Input source subnet mask. Source Port (port or port:port) Input source port number. Destination IP address Input destination IP address. Destination Subnet Mask Input destination subnet mask.
4.7.2 Outgoing Traffic Control IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. The default setting for all Outgoing traffic is Accepted. To add or remove IP filters, Click Input the access code (which is located ______) and click the The options are shown (on the following page) 35 button.
To add a filtering rule, click the button. The following window will be displayed. Filter Name Type a name for the filter rule. Rule Order Execute IP Filter order. (Available in future versions). IP Version IPv4 selected by default. Protocol User can select: TCP, TCP/UDP, UDP or ICMP. Source IP address Input source IP address. Source Subnet Mask Input source subnet mask. Source Port (port or port:port) Input source port number. Destination IP address Input destination IP address.
Click to delete a filter. 4.8 Reset Access Code To help prevent unauthorized access to your router, be sure you record your Modem Access Code and safeguard it just as you would any other password or PIN number. Should you need access to your router (for example, to make configuration changes or to change your Internet Service Provider login password) you will need the modem access code.
to se to default.
Chapter 5 Broadband This window shows the existing WAN status. 5.1 Status Click Broadband to display the status of all configured PVC(s). Port/VPI/VCI Shows the values of the ATM Port/VPI/VCI VLAN Mux Shows 802.1Q VLAN ID Con. ID Shows the connection ID Category Shows the ATM service classes Service Shows the name for WAN connection Interface Shows connection interfaces Protocol Shows the connection type, such as PPPoE, PPPoA, etc.
5.2 Configure Click Configure will bring up the following window. Input the access code (which is located ______) and click the The options are shown (on the following page) 40 button.
Select the configuration for the broadband utilization of the DSL lines. Any Changes to DSL Bonding Config will require a reboot. Select one of the three options (DSL Auto, DSL on inner pair, DSL on outer pair) from the drop down menu and tick the Enable 802.1x auto start box if required. Click the button to confirm your choice(s).
Chapter 6 Home Network The Home Network – LAN Status screen shows interface statistics for Ethernet and Wireless interfaces. 6.1 LAN Status The Network Statistics screen shows interface statistics for LAN of Ethernet interface. Here provides byte transfer, packet transfer, Error and Drop statistics for the LAN interface.) Click the button to refresh this screen.
6.2 Configure Click Configure to bring up the following window. Input the access code (which is located ______) and click the The options are shown (on the following page) 43 button.
Configure the DSL router IP address and subnet mask for the LAN interface. IP ADDRESS: ENTER THE IP ADDRESS FOR THE LAN PORT. SUBNET MASK: ENTER THE SUBNET MASK FOR THE LAN PORT. DHCP Server: To enable DHCP, select Enable DHCP server and enter Start and End IP addresses and the Leased Time. This setting configures the router to automatically assign IP, default gateway and DNS server addresses to every PC on your LAN. Static IP Lease List: A maximum of 32 entries can be configured.
Click to add a DHCP static IP lease. The following window will be displayed. Input the MAC address and Static IP address and then click To remove an entry, tick the corresponding checkbox in the Remove column and then click the Click button. to input the secondary subnet mask for the LAN port.
To create a new subnet group for LAN Devices: 1. Enter the Group name and the group name must be unique 2. Select the intended application of the new subnet group 3. Enter the corresponding IP and DHCP address 4. Passthrough MAC Address only needs to be entered in passthrough mode for the specific device that needs to share the WAN IP address 5.
IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port. Click to confirm. Ethernet Media Type: Each LAN port has Speed/Duplex Negotiation detection capability, the LAN ports detect the speed (for example, 10MBps, 100Mbps) and duplex (half-duplex or full-duplex) settings of the device on the other end of the wire and subsequently adjusts to match those settings.
6.3 Wireless Status Click Wireless Status to bring up the following window. Click to reset the screen.
6.4 Wireless Configure This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. See section: 4.4 Wireless for a detailed description.
6.5 Wireless MAC Filter When a device is using MAC filtering, any address not explicitly defined will be denied access. This MAC Filter page allows access to be restricted/allowed based on a MAC address. All (Network Interface Cards) NICs have a unique 48-bit MAC address burned into the ROM chip on the card. When MAC address filtering is enabled, you are restricting the NICs that are allowed to connect to your access point.
MAC Restrict mode: Off- disables MAC filtering; Allow – permits access for the specified MAC address; deny; reject access of the specified MAC address, then click the SET button. Option MAC Restrict Mode Description Radio buttons that allow settings of; Off: MAC filtering function is disabled. Allow: Permits PCs with listed MAC addresses to connect to access point. Deny: Prevents PCs with listed MAC from connecting to the access point.
Chapter 7 VOIP This chapter first describes the various options for configuration of the SIP voice service. It then provides detailed instructions for making telephone calls using VoIP (Voice over IP) or PSTN (Public Switched Telephone Network)(1) services. Session Initiation Protocol (SIP) is a peer-to-peer protocol used for Internet conferencing, telephony, events notification, presence and instant messaging.
7.1 Status Displays the call summary. 7.2 SIP Click SIP to bring up the following window.
servicer. 7.2.1 Global Parameters Start SIP client: Active SIP service (Internet telephony calls) Stop SIP client: Inactive SIP service (Internet telephony calls) About the setting of Global Parameters or want to know any detail information please contact with your ISP servicer. A common parameter setting.
7.2.2 Service Provider This screen contains basic SIP configuration settings. Start SIP client: Active SIP service (Internet telephony calls) Stop SIP client: Inactive SIP service (Internet telephony calls) About the setting of Service Provider or want to know any detail information please contact with your ISP servicer. VoIP settings are set by your service provider.
Once settings are configured, click Click to begin using the service. to cease using the service.
7.3 RTCP For VoIP voice quality reporting, a SIP event package is specified to report RTCP and RTCP-XR summaries; SIP method options are provided to convey such events to a collector. 7.3.1 Global Parameters A common parameter setting.
7.3.2 Service Provider This screen contains basic SIP configuration settings. NL5700 will collect and report on a set of voice quality metrics on a per-call basis to a centralized collector via SIP. There are two primary components: First, an IETF-proposed specification is customized to define the format of a Voice Quality (VQ) report and to select metrics contained within the report. Second, two candidates SIP methods are proposed for the gateway to convey the VQ report to a third-party collector.
7.4 Telephone Calls AT&T CVoIP Star Codes This tab is a list of star codes planned for use by AT&T CVoIP.
*81 Distinctive ring *82 Calling Line Identification Restriction – Cancel (make public) *83 Selective Call Forwarding - Deactivate *84 Selective Call Acceptance - Deactivate *86 Automatic Call Back Deactivate *87 Anonymous Call Rejection - Deactivate *89 Automatic Recall Deactivate *90 Call Forwarding Busy - Activate *91 Call Forwarding Busy - Deactivate *92 Call Forwarding No Answer - Activate *93 Call Forwarding No Answer - Deactivate *95 Automatic Call Control VRU *98 Voicemail
Chapter 8 Firewall The gateway is protected by firewall from unfriendly network attacks on the system. 8.1 Status Displays your firewall setting. 8.2 Inbound Filter See section: 4.7.1 Incoming Traffic Control for a detailed description. 8.3 Outbound Filter See section: 4.7.
8.4 Port Forwarding Port forwarding allows you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the Internal server with private IP addresses on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum of 32 entries can be configured. Click Port Forwarding will bring up the following window.
Click to display the following window. Select a Service User should select the service from the list. or or Custom Server User can enter the name of their choice. Server IP Address Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server). When a service is selected the port ranges are automatically configured. External Port End Enter the ending external port number (when you select Custom Server).
Custom Server). When a service is selected the port ranges are automatically configured Internal Port End Enter the internal port ending number (when you select Custom Server). When a service is selected the port ranges are automatically configured. Click Click to forward IP packets for this service to the specified server. to delete an entry.
8.5 Port Triggering Some applications require that specific ports in the router’s firewall be opened for access by the remote parties. Port Trigger dynamically opens up the ‘Open Ports’ in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the ‘Triggering Ports’. The router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the ‘Open Ports’. A maximum 32 entries can be configured.
Select an Application User should select the application from the list. Or Custom Application Or User can enter the name of their choice. Trigger Port Start Enter the starting trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured. Trigger Port End Enter the ending trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured.
Chapter 9 Maintenance The Diagnostics menu provides feedback on the connection status of the device and the ADSL link. The individual tests are listed below. 9.1 Test The individual tests are listed below. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click "Help" and follow the troubleshooting procedures.
9.2 DSL Click DSL to display the xDSL Diagnostics window. Consult the table below for descriptions of each field.
Field Description Mode Line Coding format, that can be selected G.dmt, G.lite, T1.413, ADSL2 Traffic Type Channel type Interleave or Fast Status Lists the status of the DSL link Link Power State Link output power state. Line Coding Trellis On/Off SNR Margin (dB) Signal to Noise Ratio (SNR) margin Attenuation (dB) Estimate of average loop attenuation in the downstream direction. Output Power (dBm) Total upstream output power Attainable Rate (Kbps) The sync rate you would obtain.
(BER). A small pop-up window will open after the button is pressed, as shown below. Click Start to start the test or click Close to cancel the test. After the BER testing is complete, the pop-up window will display as follows.
9.2.2 Reset Statistics Click to refresh the screen. 9.2.3 Draw Graph Tone Click to display the current xDSL bits per tone status. The X axis represents Tone Number and the Y axis represents Bit Allocation.
9.2.4 Draw Loss of Signal Graph Click to display the loss of signal within each 15 minute intervals for the last 24 hours. The X axis represents Time and the Y axis represents Errors Observed. 9.2.
intervals for the last 24 hours. The X axis represents Time and the Y axis represents Errors Observed. 9.2.6 Loss of Power Click to display the loss of power within each 15 minute intervals for the last 24 hours. The X axis represents Time and the Y axis represents Errors Observed.
9.3 Ping/Traceroute/NSLookup Click Ping/Traceroute/NSLookup to bring up the following window. 9.3.1 Ping Ping: Used to test the reach ability of a host on an Internet Protocol (IP) network and to measure the round-trip time for messages sent from the originating host to a destination computer Click to seek a reply from an IP address.
9.3.2 TraceRoute TraceRoute: Used to show the route taken by packets across an IP network Traceroute is often used for network troubleshooting. By showing a list of routers traversed, it allows the user to identify the path taken to reach a particular destination on the network. Click to trace the route of an IP address. 9.3.
Click to lookup the name server of an IP address. 9.4 System Log The System Log option allows you to view the system events log. Click System Log to bring up the following window.
9.4.1 Refresh Click to update the System Log. 9.4.2 Export Syslog Click to bring up the following window.
Click to save the system log file.
9.5 Password Click Password to bring up the following window.
9.5.1 Use New Access Code Select User, enter the current access code and the new access code. Hen retype the new access code. Click 9.5.2 Clear Input Click to delete what you have entered. 9.5.3 Reset to Default Access Code Click to reset to default.
9.6 Upgrade Click Upgrade to bring up the following window. Input the access code (which is located ______) and click The options are shown (on the following page) Click to start the upgrade process.
9.7 Reboot Click to reboot the gateway. The following window will be displayed.
9.8 Factory Reset Click Factory Reset to bring up the following window. Input the access code (which is located ______) and click The options are shown (on the following page) Click to restore the DSL gateway to the factory defaults.
Click OK to confirm. Click OK to confirm.
Appendix A: Firewall Stateful Packet Inspection Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. Denial of Service attack Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
Destination Port: This can take on either a single port number or a range of port numbers. Packets having a destination port equal to this value or falling within the range of port numbers (portX : portY) will be dropped. Examples: 1. Filter Name : Out_Filter1 Protocol : TCP Source Address : 192.168.1.45 Source Subnet Mask : 255.255.255.0 Source Port : 80 Dest. Address : NA Dest. Sub. Mask : NA Dest. Port : NA This filter will Drop all TCP packets coming from LAN with IP Address/Sub.
Protocol: Can take on any values from: TCP/UDP, TCP, UDP or ICMP Source IP Address/Source Subnet Mask: Packets with the particular "Source IP Address/Source Subnet Mask" combination will be accepted. Source Port: This can take on either a single port number or a range of port numbers. Packets having a source port equal to this value or falling within the range of port numbers (portX : portY) will be accepted.
2. Filter Name : In_Filter2 Protocol : UDP Source Address : 210.168.219.45 Source Subnet Mask : 255.255.0.0 Source Port : 5060:6060 Dest. Address :192.168.1.45 Dest. Sub. Mask : 255.255.255.0 Dest. Port : 6060:7070 This rule will ACCEPT all UDP packets coming from WAN interface mer_0_35/nas_0_35 with IP Address/Sub. Mask 210.168.219.45/16 and a source port in the range of 5060 to 6060, destined to 192.168.1.45/24 and a destination port in the range of 6060 to 7070.
Appendix B: Pin Assignments Line port (RJ14) Pin Definition Pin Definition 1 - 4 ADSL_TIP1 2 ADSL_TIP2 5 ADSL_RING2 3 ADSL_RING1 6 - LAN Port (RJ45) Pin Definition Pin Definition 1 Transmit data+ 5 NC 2 Transmit data- 6 Receive data- 3 Receive data+ 7 NC 4 NC 8 NC 89
Appendix C: Specifications Rear Panel RJ-14 X1 for ADSL2+ bonded, RJ-45 X 4 for LAN, Reset Button X 1, WPS button x1, WIFI button x1 Wi-Fi Antenna x 1 ADSL ADSL standard ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2AnnexM ADSL2 Bonded Downstream : 48 Mbps Upstream : 2.6 Mbps ADSL2+ Bonded Downstream : 48 Mbps Upstream : 2.6 Mbps ADSL2+ non-Bonded Downstream : 24 Mbps Upstream : 1.3 Mbps ADSL2 non-Bonded Downstream : 12 Mbps Upstream : 1.3 Mbps G.
selected according to the environment ATM Attributes RFC 2364 (PPPoA), RFC 2684 (RFC 1483) Bridge/Route; RFC 2516 (PPPoE); RFC 1577 (IPoA) Support PVCs 16 AAL type AAL5 ATM service class UBR/CBR/VBR-rt/VBR-nrt ATM UNI support UNI3.1/4.0 OAM F4/F5 Yes Management SNMP, Telnet, Web-based management, Configuration backup and restoration Software upgrade via HTTP, TFTP server, or FTP server Supports TR-069/TR-098/TR-111 for Remote Management Bridge Functions Transparent bridging and learning IEEE 802.
Application Passthrough PPTP, L2TP, IPSec, VoIP, Yahoo messenger, ICQ, RealPlayer, NetMeeting, MSN, X-box, etc OS Supported for USB driver Windows 2000/XP/ME/98SE Power Supply External power adapter 100-240Vac Environment Condition Operating temperature 0 ~ 40 degrees Celsius Relative humidity 5 ~ 95% (non-condensing) Dimensions 205 mm (W) x 48 mm (H) x 145 mm (D) Certifications FCC Part 15 class B, FCC Part 68, CE Kit Weight Kit 0.
Appendix D: SSH Client Linux OS comes with ssh client. Microsoft Windows does not have ssh client but there is a public domain one “putty” that you can download. http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the router using Linux ssh client: From LAN: Use the router WEB UI to enable SSH access from LAN. (default is enabled) type: ssh -l admin 192.168.1.1 From WAN: In the router, use WEB UI to enable SSH access from WAN.
