CT-5624 4-Port ADSL2+ Router User Manual Version A1.
Preface This manual provides information related to the installation, operation, and application of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at INT-support@comtrend.com For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.
Table of Contents CHAPTER 1 INTRODUCTION........................................................................................................4 CHAPTER 2 INSTALLATION..........................................................................................................5 CHAPTER 3 CONNECTING THE HARDWARE ..........................................................................6 CHAPTER 4 LOGIN VIA THE WEB BROWSER .........................................................................7 4.
9.5.2 IP Addresses ...................................................................................................................69 9.5.3 Passwords .......................................................................................................................70 9.6 UPDATE SOFTWARE ........................................................................................................................71 9.7 SAVE AND REBOOT ..........................................................................
Chapter 1 Introduction The CT-5624 series ADSL2+ compact and high performance Ethernet router provides four 10/100 Ethernet Interfaces, and one ADSL line interface to access the Internet, incorporating LAN or Video on Demand over one ordinary telephone line, at speeds of up to 24 Mbps. It also has full routing capabilities to segment/route IP protocol and supports advanced security functions. The CT-5624 is for ADSL over POTS (i.e. Annex A). The CT-5624 series can operate in router or bridge mode.
Chapter 2 Installation Front Panel The front panel contains lights called LEDs that indicate the status of the unit. Front Panel LEDs INTERNET/DSL Red: No ADSL link LAN 1x-4X (Green) Orange on: The ADSL connection is established and the device had attempted to obtain an IP address but failed (reason: no DHCP response, no PPPoE response, PPPoE authentication failed, no IP address from IPCP, etc.) Red/Orange interlacing: the DSL is training.
Chapter 3 Connecting the Hardware You connect the device to the phone jack, the power outlet, and your computer or network. Step 1. Connect the ADSL cable and optional telephone. Connect one end of the provided phone cable to the port labeled ADSL on the rear panel of the device. Connect the other end to your wall phone jack. You can attach a telephone line to the device. This is helpful when the ADSL line uses the only convenient wall phone jack.
Chapter 4 Login via the Web Browser This section describes how to manage the router via a Web browser via the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. The Web page is best viewed with Microsoft Internet Explorer 5.0 and later. 4.1 IP Configuration The default IP address of the CT-5624 (LAN port) is 192.168.1.1. To configure the CT-5624 for the first time, the configuration PC must have a static IP address within the 192.168.1.x subnet.
4.2 Login Procedure Perform the following steps to bring up the Web user interface and configure the CT-5624. To log on to the system from the Web browser, follow the steps below: STEP 1: Start your Internet browser. Type the IP address for the router in the Web address field. For example, if the IP address is 192.168.1.1, type http://192.168.1.1 STEP 2: You will be prompted to enter your user name and password. Type root in the user name and 12345 in the password field, and click OK.
4.3 Default Settings The following default settings are present when setting up the router for the first time. The PC running the browser can be attached to the Ethernet. • One PPPoE PVC (VPI=8, VCI=35) • NAT Enabled and Firewall Disabled • DHCP server on LAN interface: Enabled • WAN IP address: None • LAN port IP address: 192.168.1.
Chapter 5 Device Information The Summary screen appears as shown below. NOTE: The selections available on the main menu are based upon the configured connections and the active user account.
5.1 WAN This screen displays the configured PVC(s) and their status. VPI/VCI Con. ID Category Service Interface Protocol IGMP NAT FIREWALL QoS State Status IP Address Shows the values of the ATM VPI/VCI Shows the connection ID Shows the ATM service classes Shows the name for WAN connection Shows connection interfaces Shows the connection type, such as PPPoE, PPPoA, etc.
5.2 Statistics Selection of the Statistics screen provides statistics for the Network Interface of LAN, WAN, ATM and ADSL. All statistics screens are updated every 15 seconds. 5.2.1 LAN Statistics The Network Statistics screen shows interface statistics for the Ethernet interface. (The Network Statistics screen shows interface statistics for LAN of Ethernet interface. Here provides byte transfer, packet transfer, Error and Drop statistics for the LAN interface.
5.2.2 WAN Statistics Service VPI/VCI Protocol Interface Received/Transmitted - Bytes - Pkts - Errs - Drops Shows the service type Shows the values of the ATM VPI/VCI Shows the connection type, such as PPPoE, PPPoA, etc.
5.2.3 ATM statistics The following figure shows the ATM statistics screen. ATM Interface Statistics Field Description In Octets Number of received octets over the interface Out Octets Number of transmitted octets over the interface In Errors In Unknown Number of cells dropped due to uncorrectable HEC errors Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with invalid cell header patterns.
Out Errors In Discards Out Discards Number of received AAL5/AAL0 CPCS PDUs that could be transmitted due to errors. Number of received AAL5/AAL0 CPCS PDUs discarded due to an input buffer overflow condition.
5.2.4 ADSL Statistics The following figure shows the ADSL Network Statistics screen. Within the ADSL Statistics window, a bit Error Rate Test can be started using the ADSL BER Test button. The Reset button refreshes the ADSL statistics.
Field Mode Type Line Coding Status Link Power State SNR Margin (dB) Attenuation (dB) Output Power (dBm) Attainable Rate (Kbps) Rate (Kbps) Description T1.413, G.lite, G.DMT, ADSL2/2+ or Re-ADSL Channel type Interleave or Fast Line Coding format, that can be selected G.dmt, G.lite, T1.413, ADSL2, Annex L and Annex M Lists the status of the DSL link Link output power state. Signal to Noise Ratio (SNR) margin Estimate of average loop attenuation in the downstream direction.
Within the ADSL Statistics window, a Bit Error Rate (BER) test can be started using the ADSL BER Test button. A small window will open when the button is pressed; it will appear as shown below. Click Start to start the test or Close. If the test is successful, the pop-up window will display as follows.
5.3 Route Choose Route to display the routes that the route information has learned. 5.4 ARP Click ARP to display the ARP information.
5.5 DHCP Click DHCP to display the DHCP information.
Chapter 6 Quick Setup The Quick Setup allows the user to configure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup. You can either manually customize the router or follow the online instruction to set up the router. The CT-5624 ADSL router supports the following five network operating modes over an ATM PVC WAN interface.
6.1 Auto Quick Setup The auto quick setup requires the ADSL link to be up. The ADSL router will automatically detect the PVC. You only need to follow the online instructions that you are prompted. 1. Select Quick Setup to display the DSL Quick Setup screen. 2. Click Next to start the setup process. Follow the online instructions to complete the setting. This procedure will skip some processes like PVC index, or encapsulation. 3. After the settings are complete, you can use the ADSL service.
6.2 Manual Quick Setup STEP 1: Click Quick Setup and un-tick the DSL Auto-connect checkbox to enable manual configuration of the connection type. Un-tick this checkbox to enable manual setup and display the following screen. STEP 2: Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI). Select Enable Quality Of Service if required. Enabling IP QoS for a PVC improves performance for selected classes of applications.
6.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) 1. Select the PPP over ATM (PPPoA) or PPP over Ethernet (PPPoE) radio button and click Next. The following screen appears: PPP Username/PPP Password Give “PPP Username”, “PPP Password” and “PPPoE Service Name”, then select the “Authentication Method” (AUTO/PAP/CHAP/MSCHAP). Please contact your ISP for the information. The WEB user interface allows a maximum of 256 characters in the PPP user name and a maximum of 32 characters in PPP password.
PPP IP Extension The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specially requires this setup, do not select it. The PPP IP Extension supports the following conditions: • Allows only one PC on the LAN • The public IP address assigned by the remote side using the PPP/IPCP protocol is actually not used on the WAN PPP interface. Instead, it is forwarded to the PC’s LAN interface through DHCP.
Enable WAN Service checkbox: Tick this item to enable the ATM service. Untick it to stop the ATM service. Service Name: This is user-defined. 3. After entering your settings, select Next. The following screen appears. This page allows the user to configure the LAN interface IP address, subnet mask and DHCP server.
4. Click Next to display the WAN Setup-Summary screen that presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
5. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5624 is ready for operation and the LEDs display as described in the LED description tables. 6.2.2 To 1. 2. 3. MAC Encapsulation Routing (MER) configure MER, do the following. Select Quick Setup and click Next.
4. Click Next to display the following screen. Enable NAT checkbox: If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side, this checkbox should be de-selected to free up system resources for better performance.
5. Upon completion, click Next. The following screen appears. The Device Setup page allows the user to configure the LAN interface IP address and DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server and enter the Start and End IP address and the DHCP Leased Time.
7. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5624 is ready for operation and the LEDs display as described in the LED description tables. 6.2.3 To 1. 2. 3. 4. IP Over ATM configure IP Over ATM, Select Quick Setup and click Next. Enter the PVC Index and click Next.
NOTE: DHCP is not supported over IPoA. The user must enter the IP address or WAN interface for the default gateway setup, and the DNS server addresses provided by the ISP. 5. Click Next. The following screen appears. Enable NAT checkbox If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up.
The user must configure the IP Address and the Subnet Mask. To use the DHCP service on the LAN, select the Enable DHCP server checkbox, and enter the Start IP addresses, the End IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs.
7. Click Next to display the following screen. 8. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5624 is ready for operation and the LEDs display as described in the LED description tables. 6.2.4 Bridging Select the bridging mode. 1. 2. 3. 4. To configure Bridging, do the following.
5. Click the Next button to continue. Enter the IP address for the LAN interface. The default IP address is 192.168.1.1. The LAN IP interface in bridge operating mode is needed for local users to manage the ADSL router. Notice that there is no IP address for the WAN interface in bridge mode, and the remote technical support cannot access the ADSL router.
6. The following screen will be displayed. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
Chapter 7 Advanced Setup This chapter includes the following sections: WAN, LAN, NAT, Security, QoS, Routing, DNS, DSL, and Port Mapping 7.1 WAN This screen shows the default WAN interface. Users can choose to Add, Edit, or Remove these WAN interfaces. The Save/Reboot button saves the current configuration and reboots the router. VlanID This function means one can add an 802.1Q VLAN tag on PPPoE/MER or Bridge mode. It means the packets are sent to WAN and a specific VlanID (802.
7.2 LAN Configure the DSL Router IP Address and Subnet Mask for LAN interface. Save button only saves the LAN configuration data. Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable IGMP Snooping: Enable by ticking the box.
Configure the second IP address by ticking the checkbox shown below. IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port. NOTE: The Save button saves new settings to allow continued configuration while the Save/Reboot button not only saves new settings but also reboots the device to apply the new configuration (i.e. all new settings). Ethernet Media Type: Choose Auto, 10_Half, 10_Full, 100_Half or 100_Full for each Ethernet port. 7.
To add a Virtual Server, click the Add button. The following will be displayed. Select a Service Or Custom Server Server IP Address User should select the service from the list. Or User can enter the name of their choice. Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server). When a service is selected the port ranges are automatically configured. Enter the ending external port number (when you select Custom Server).
7.3.2 Port Triggering Some applications require that specific ports in the Router's firewall be opened for access by the remote parties. Port Trigger dynamically opens up the 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.
7.3.3 DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. Enter the computer's IP address and click "Apply" to activate the DMZ host. Clear the IP address field and click "Apply" to deactivate the DMZ host.
7.4 Security To display the Security function, you must enable the firewall in WAN Setup. 7.4.1 IP Filtering IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click 'Save/Apply' to save and activate the filter. Outgoing Note: The default setting for all Outgoing traffic is Accepted.
Filter Name Protocol Source IP address Source Subnet Mask Source Port (port or port:port) Destination IP address Destination Subnet Mask Destination port (port or port:port) Type a name for the filter rule. User can select from: TCP, TCP/UDP, UDP or ICMP. Enter source IP address. Enter source subnet mask. Enter source port number. Enter destination IP address. Enter destination subnet mask. Enter destination port number. Incoming Note: The default setting for all Incoming traffic is Blocked.
To configure the parameters, please reference Outgoing table above. 7.4.2 MAC Filter NOTE: This function is only available when in bridge mode. PPPoE, PPPoA, IPoA and MER use IP Filtering (pg. 43) to perform a similar function. Each network device has a unique 48-bit MAC address. This can be used to filter (block or forward) packets based on the originating device. MAC filtering policy and rules for the CT-5624 can be set according to the following procedure.
Choose Add or Remove to configure MAC filtering rules. The following screen will appear when you click Add. Create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them must be met. Click Save/Apply to save and activate the filter rule.
7.5 Quality of Service To display this function, you must enable QoS in WAN Setup. Choose Add to configure network traffic classes.
The screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header TOS byte. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect. Click 'Save/Apply' to save and activate the rule.
Destination Subnet Mask Destination port (port or port:port) SET-2 802.1p Priority Traffic Class Name Priority IP Precedence IP Type Of Service Physical LAN Port Protocol Source IP Address Source Subnet Mask Source Port (port or port:port) Destination IP address Destination Subnet Mask Destination port (port or port:port) 802.1p Priority Enter destination subnet mask. Enter destination port number. Select between 0-7. Enter name for traffic class Select Low, Medium or High. Select between 0-7.
7.6.2 Static Route Choose Static Route to display the Static Route screen. The Static Route screen lists the configured static routes, and allows configuring static routes. Choose Add or Remove to configure the static routes. To add static route, click the Add button to display the following screen. Enter the destination network address, subnet mask, gateway and available WAN interface then click Save/Apply to add the entry to the routing table.
7.6.3 RIP To activate RIP for the device, select the 'Enabled' radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface. Click the 'Save/Apply' button to save the configuration, and to start or stop RIP based on the Global RIP mode selected. Note: This screenshot is based on PPPoE encapsulation.
7.7 DNS 7.7.1 DNS Server If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, enter the primary and optional secondary DNS server IP addresses. Click 'Save' button to save the new configuration. You must reboot the router to make the new configuration effective. 7.7.
NOTE: The Add/Remove buttons will only be displayed if the CPE has already been assigned an IP address from the remote server. To add a dynamic DNS service, simply click the Add button. The following screen will be displayed: D-DNS provider Hostname Interface Username Password Select a dynamic DNS provider from the list. Enter the name for the dynamic DNS server. Select the interface from the list. Enter the username for the dynamic DNS server. Enter the password for the dynamic DNS server.
7.8 DSL To access the DSL settings, first click On Advanced Setup and then click on DSL. The DSL Settings dialog box allows you to select an appropriate modulation mode. Option G.dmt Enabled G.Lite Enabled T1.413 Enabled Description Sets G.Dmt if you want the system to use G.Dmt mode. Sets G.Lite if you want the system to use G.Lite mode. Sets the T1.413 if you want the system to use only T1.413 mode. ADSL2 Enabled The device can support the functions of the ADSL2.
7.9 Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. As shown below, when you tick the Enable virtual ports on, all of the LAN interfaces will be grouped together as a default.
To create a group from the list, first enter the group name and then select from the available interfaces on the list. Automatically Add Clients With the Following DHCP Vendor IDs: Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Port Mapping is enabled. There are 4 PVCs (0/33, 0/36, 0/37, 0/38).
In the LAN side, PC can get IP address from CPE's dhcp server and access Internet via PPPoE (0/33). If the setup-box was connected with interface "ENET1" and send a dhcp request with vendor id "Video", CPE's dhcp server will forward this request to ISP's dhcp server. And CPE will change the port mapping configuration automatically. The portmapping configuration will become: 1. Default : ENET2, ENET3, and ENET4. 2. Video: nas_0_36, nas_0_37, nas_0_38 and ENET1. 7.
7.11 TraceRoute This screen performs the same function as the console command of the same name. It allows you to trace the path between the router and any location on the LAN or WAN within 30 hops of the router. Enter the IP address of the location you wish to trace and click TraceRoute. NOTE: In the example above, the final IP address listed is the target IP address (i.e. 172.16.2.199). If the target IP address does not appear at the end of this list, ping the target IP address to test the connection.
Chapter 8 Diagnostics The Diagnostics menu provides feedback on the connection status of the CT-5624 and the ADSL link. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click Help and follow the troubleshooting procedures.
In router modes, such as PPPoE, this screen will also include ISP tests as shown. ISP Connection Pass: Indicates that the router can access the ISP Default Gateway or Domain Name Server (DNS). Fail: Indicates that the router cannot access the ISP Default Gateway or Domain Name Server (DNS).
Chapter 9 Management The system administrator can do the following functions to manage the configurations, events, SNMP information, user accounts, and software update of the CT-5624. 9.1 Settings The Settings option allows you to back up your settings to a file and retrieve the file settings. The settings can be saved from ATUR to PC. The saved setting file can also be loaded from PC to ATUR. These 2 functions can help the system administrator to manage large amount of ATURs efficiently.
9.1.2 Update Settings This option under Management>Settings updates your router settings using your saved files.
9.1.3 Restore Default Clicking the Restore Default Configuration option in the Restore Settings screen can restore the original factory installed settings. NOTE: This entry has the same effect as the hardware reset-to-default button. The CT-5624 board hardware and the boot loader support the reset to default button. If the reset button is continuously pushed for more than 5 seconds, the boot loader will erase the entire configuration data saved on the flash memory.
9.2 System Log The System Log option under Management>Settings allows you to view the system events log, or to configure the System Log options. The default setting of system log is disabled. Follow the steps below to enable and view the system log. 1. Click Configure System Log to display the following screen. 2. Select from the desired Log options described in the following table, and then click SAVE/Apply.
Option Log Log level Description Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled. To enable it, tick Enable and then Apply button. Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the CT-5624 SDRAM.
9.3 SNMP Agent Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device. Select desired settings and click Save/Apply to apply changes. Enable or Disable the SNMP Agent. Relationship between an Agent and Managers Read Default is “public” Community: Set Community: Default is “private” System Name: Default is “Comtrend” System Location: Shows the location of the system.
9.4 Internet Time The Internet Time option under Management menu bar configures the Modem’s time. To automatically synchronize with Internet time servers, tick the corresponding box displayed on the screen. Then click Save/Apply.
9.5 Access Control The Access Control option under Management menu bar configures the access-related parameters, including three parts: Services, IP Address, and Passwords. 9.5.1 Services The Services option limits or opens the access services over the LAN or WAN. These services are provided FTP, HTTP, ICMP, SNMP, TELNET, and TFTP. The “Services” can be enabled for LAN side, WAN side, or both. Enable the service by checking the item in the corresponding checkbox, and then click Save/Apply.
9.5.2 IP Addresses The IP Addresses option limits the access by IP address. If the Access Control Mode is enabled, only the allowed IP addresses can access the router. Before you enable it, configure the IP addresses by clicking the Add button. Enter the IP address and click Apply to allow the PC with this IP address to manage the router.
9.5.3 Passwords The Passwords option configures the access passwords for the router. Access to your DSL router is controlled through the following user accounts: • root has unrestricted access to change and view the configuration • support is used for remote maintenance and diagnostics. • user has limited access to device information, statistics and software updates. Use the fields below to enter up to 16 characters and click Save/Apply to change or create passwords.
9.6 Update software The Update Software screen allows you to obtain an updated software image file from your ISP. Manual software upgrades from a locally stored file can be performed using the following screen. Step 1: Obtain an updated software image file from your ISP. Step 2: Enter the path to the image file location in the box below or click the Browse button to locate the image file. Step 3: Click the "Update Software" button once to upload the new image file.
9.7 Save and Reboot The Save/Reboot options saving the configurations and reboot the router. Close the DSL Router Configuration window and wait for 2 minutes before reopening your web browser. If necessary, reconfigure your PC's IP address to match your new configuration.
Appendix A: Firewall Stateful Packet Inspection Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. Denial of Service attack Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
This filter will Drop all TCP packets coming from LAN with IP Address/Sub. Mask 192.168.1.45/24 having a source port of 80 irrespective of the destination. All other packets will be Accepted. 2. Filter Name Protocol Source Address Source Subnet Mask Source Port Dest. Address Dest. Sub. Mask Dest. Port : : : : : : : : Out_Filter2 UDP 192.168.1.45 255.255.255.0 5060:6060 172.16.13.4 255.255.255.0 6060:7070 This filter will drop all UDP packets coming from LAN with IP Address/Sub.Mask 192.168.1.
mer_0_35/nas_0_35 with IP Address/Sub. Mask 210.168.219.45/16 having a source port of 80 irrespective of the destination. All other incoming packets on this interface are DROPPED. 2. Filter Name Protocol Source Address Source Subnet Mask Source Port Dest. Address Dest. Sub. Mask Dest. Port : : : : : : : : In_Filter2 UDP 210.168.219.45 255.255.0.0 5060:6060 192.168.1.45 255.255.255.0 6060:7070 This rule will ACCEPT all UDP packets coming from WAN interface mer_0_35/nas_0_35 with IP Address/Sub.Mask 210.
Example 1: Global Policy: Forwarded Protocol Type: PPPoE Dest. MAC Addr: 00:12:34:56:78 Source MAC Addr: Null Frame Direction: LAN => WAN WAN Interface Selected: br_0_34/nas_0_34 Addition of this rule drops all PPPoE frames going from LAN-side to WAN-side with a Dest. MAC Addr. of 00:12:34:56:78 irrespective of its Source MAC Addr. on the br_0_34 WAN interface. All other frames on this interface are forwarded. Example 2: Global Policy: Blocked Protocol Type: PPPoE Dest.
Appendix B: Pin Assignments Line Port (RJ11) Pin 1 2 3 Definition ADSL_RING Pin 4 5 6 Definition ADSL_TIP - LAN Port (RJ45) Pin 1 2 3 4 Definition Transmit data+ Transmit dataReceive data+ NC - 77 - Pin 5 6 7 8 Definition NC Receive dataNC NC
Appendix C: Specifications Rear Panel RJ-11 X1 for ADSL, RJ-45 X 4 for LAN, Power Button X 1, Reset Button X 1 ADSL ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2 G.992.5 (ADSL2+) Downstream : 24 Mbps Upstream : 1.3 Mbps G.992.3 (ADSL2) Downstream : 12 Mbps Upstream : 1.3 Mbps G.DMT Downstream : 8 Mbps Upstream : 832 Kbps Ethernet Standard IEEE 802.3, IEEE 802.
Power Supply External power adapter 110 Vac or 220 Vac Environment Condition Operating temperature 0 ~ 50 degrees Celsius Relative humidity 5 ~ 90% (non-condensing) Dimensions 140 mm (W) x 40 mm (H) x 133 mm (D) NOTE: Specifications are subject to change without notice - 79 -
