CT-5611T ADSL2+ Combo Router User’s Manual Version A1.
Warning Before servicing or disassembling this equipment, always disconnect all power and telephone lines from the device. Use an appropriate power supply and a UL Listed telephone line cord. Specification of the power supply is clearly stated in Appendix B - Specifications. Preface This manual provides information to network administrators. It covers the installation, operation and applications of the ADSL2+ combo router.
Table of Contents CHAPTER 1 1.1 1.2 1.3 FEATURES ............................................................................................................ 4 APPLICATION ....................................................................................................... 5 FRONT PANEL LED INDICATORS ......................................................................... 6 CHAPTER 2 2.1 2.2 2.3 2.4 INSTALLATION..................................................................................
6.4.1 IP Filtering................................................................................................ 65 6.4.2 Parental Control ....................................................................................... 68 6.5 QUALITY OF SERVICE......................................................................................... 69 6.6 ROUTING ............................................................................................................ 71 6.6.1 Default Gateway ...................
Chapter 1 Introduction The CT-5611T ADSL2+ compact and high performance combo router provides one 10/100 Ethernet Interface and one USB interface, offering ADSL connectivity at speeds of up to 24 Mbps. It also has full routing capabilities to segment/route IP protocol, and supports advanced security functions. 1.
1.2 Application The following diagram depicts the application of the CT-5611T.
1.3 Front Panel LED Indicators The front panel LEDs are shown in the picture below, followed by an explanation in the table below. LED Color Mode Function On The router is powered up. Off The router is powered down. Red On POST (Power On Self Test) fail (not bootable) or router failure which could be any error of internal sequence or state that will not allow the router to connect to the DSLAM, or send data. Green On The ADSL link is established. Off The ADSL link is not established.
On A USB link is established. Off A USB link is not established. Green Blink Data transmitting or receiving over USB. Green On Normal operating status. Off The ADSL link is terminated. Blink Data transmitting or receiving over ADSL. On Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, PPPoE authentication failed, no IP address from IPCP, etc.) For bridged mode, the indicator light is off.
Chapter 2 Installation 2.1 Hardware Installation Reset Button Follow the instructions below to complete the hardware connections. Connection to LINE port If you wish to connect both the router and a telephone, connect the LINE port to a POTS splitter with a RJ11 connection cable. Connection to LAN port To connect to a hub or PC, use a RJ45 cable. The port is auto-sensing MDI/X and either straight-through cable or crossover cable can be used.
After all connections have been made, turn the power-switch to the on position. After powering on, the router performs a self-test. Wait for a few seconds until the test is finished, then the router will be ready to operate. Reset Button Restore the default parameters of the router by holding down the device’s Reset button until the LED’s start blinking simultaneously (about 5 seconds).
STEP 2: When the screen displays as below, wait until the drivers are fully installed.
STEP 3: Click the Finish button, when the screen displays as below. STEP 4: Installation is complete.
2.3 USB Driver Manual Installation(64bit OS) Before you connect your router’s USB cable to your PC, you must load the ADSL USB drivers. This manual USB driver installation supports Windows XP 64 bit. To connect the router to a PC using the USB interface, you need to use a standard USB cable and install the USB interface software.
Note: This screen won’t be displayed if the USB Driver has been previously un/installed. STEP 3: If you are installing the software from a disk, insert the disk.
STEP 4: Select the location of the file using the Browse button. Normally, the file is on the CD-ROM shipped with the device. STEP 5: Locate the Vista folder, and click the OK button.
STEP 6: When the screen displays as below, click the NEXT button.
STEP 7: Click the Finish button, when the screen displays as below.
STEP 8: Installation is complete.
2.4 Un-installing the USB Driver STEP 1: Click Start, Settings and then Control Panel as shown here. STEP 2: When the following screen is displayed, click on the Add/Remove Hardware Icon. STEP 3: When the following screen is displayed, click Next.
STEP 4: When the following screen is displayed, select Uninstall/Unplug a device (as shown here). Then, click Next. STEP 5: When the following screen is displayed, select Uninstall a device (as shown here). Then, click Next.
STEP 6: When the following screen is displayed, select the device that you want to uninstall. Then, click Next.
STEP 7: When the following screen is displayed, click Next to confirm that you want to uninstall the device. STEP 8: When the following screen is displayed, click Finish as un-installation is complete.
Chapter 3 Login via the Web Browser This section describes how to manage the router via a Web browser via the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. (The Web page is best viewed with Microsoft Internet Explorer 5.0 and later): A unique default user account is assigned with user name root and password 12345. The user can change the default password later when logged in to the device. 3.
3.2 Login Procedure Perform the following steps to bring up the Web user interface and configure the CT5611T. To log on to the system from the Web browser, follow the steps below: STEP 1: Start your Internet browser. Type the IP address for the router in the Web address field. For example, if the IP address is 192.168.1.1, type http://192.168.1.1 STEP 2: You will be prompted to enter your user name and password. Type root in the user name field and 12345 in the password field, and click OK.
24
3.3 Default Settings During power on initialization, the CT-5611T initializes all configuration attributes to default values. It will then read the configuration profile from the Permanent Storage section on the flash memory. The default attributes are overridden when identical attributes with different values are configured. The configuration profile in Permanent Storage can be created via the Web user interface, the console, or telnet user interface, or other management protocols.
Chapter 4 Quick Setup After login, the Quick Setup screen appears as shown. Note: The selections available on the left side of menu are based upon the configured connection.
4.1 WAN Click Device Info on the menu bar to display the WAN option. Then, click WAN on the Device Info menu bar to display the configured PVC(s) and the status. VPI/VCI Shows the values of the ATM VPI/VCI Con. ID Shows the connection ID Category Shows the ATM service classes Service Shows the name for WAN connection Interface Shows connection interfaces Protocol Shows the connection type, such as PPPoE, PPPoA, etc.
4.2 Statistics Selection of the Statistics screen provides statistics for the Network Interface of LAN, WAN, ATM and ADSL. All statistics screens are updated every 15 seconds.
4.2.1 LAN Statistics The Network Statistics screen shows interface statistics for Ethernet and USB interfaces. (The Network Statistics screen shows interface statistics for LAN of Ethernet and USB interfaces. This shows byte transfer, packet transfer, Error and Drop statistics for the LAN interface.
4.2.2 WAN Statistics The following figure shows the WAN statistics screen. Service VPI/VCI Protocol Shows the service type Shows the values of the ATM VPI/VCI Shows the connection type, such as PPPoE, PPPoA, etc.
4.2.3 ATM statistics The following figure shows the ATM statistics screen. ATM Interface Statistics Field Description In Octets Number of received octets over the interface Number of transmitted octets over the interface Out Octets In Errors Number of cells dropped due to uncorrectable HEC errors In Unknown Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with invalid cell header patterns.
ATM AAL5 Layer Statistics over ADSL interface Field In Octets Out Octets In Ucst Pkts Out Ucast Pkts In Errors Out Errors In Discards Out Discards Description Number of received AAL5/AAL0 CPCS PDU octets Number of received AAL5/AAL0 CPCS PDUs octets transmitted Number of received AAL5/AAL0 CPCS PDUs passed to a higher-layer for transmission Number of received AAL5/AAL0 CPCS PDUs received from a higher layer for transmissions Number of received AAL5/AAL0 CPCS PDUs received that contain an error.
4.2.4 ADSL Statistics The following figure shows the ADSL Network Statistics screen. Within the ADSL Statistics window, a bit Error Rate Test can be started using the ADSL BER Test button. The Reset button resets the statistics.
Field Mode Type Line Coding Status Link Power State SNR Margin (dB) Attenuation (dB) Output Power (dBm) Attainable Rate (Kbps) Rate (Kbps) Super Frames Super Frame Errors RS Words RS Correctable Errors RS Uncorrectable Errors HEC Errors OCD Errors LCD Errors Total ES: Total SES: Total UAS: Description Modulation protocol G.dmt, G.lite, T1.413, ADSL2, ADSL2+ Channel type Interleave or Fast Trellis On/Off Lists the status of the DSL link Link output power state.
4.2.5 Route Choose Route to display the routes that the route information has learned. 4.2.6 ARP Click ARP to display the ARP information.
4.2.7 DHCP Click DHCP to display the DHCP information.
Chapter 5 Quick Setup The Quick Setup allows the user to configure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup. You can either manually customize the router or follow the online instruction to set up the router. The CT-5611T ADSL router supports the following five network operating modes over an ATM PVC WAN interface.
5.1 Auto Quick Setup The auto quick setup requires the ADSL link to be up. The ADSL router will automatically detect the PVC. You only need to follow the online instructions that you are prompted. 1. Select Quick Setup to display the DSL Quick Setup screen. 2. Click Next to start the setup process. Follow the online instructions to complete the setting. This procedure will skip some processes like PVC index, or encapsulation. 3. After the settings are complete, you can use the ADSL service. 5.
STEP 2: Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI). Select Enable Quality Of Service if required. Click Next. STEP 3: Then, choose the Encapsulation mode. STEP 4: Choosing different connection types pops up different settings requests. Enter appropriate settings that are requested by your service provider. The following descriptions state each connection type setup separately. Select Enable 802.1q (by ticking the box) if required, and input a number for the VLAN ID.
5.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) 1. Select the PPP over ATM (PPPoA) or PPP over Ethernet (PPPoE) radio button and click Next. The following screen appears: PPP USERNAME/PPP PASSWORD The PPP Username and the PPP password requirement are dependent on the particular requirements of the ISP or the ADSL service provider. The WEB user interface allows a maximum of 256 characters in the PPP user name and a maximum of 32 characters in PPP password.
Disconnect if no activity The CT-5611T can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand check box. When the checkbox is ticked, you need to enter the inactivity timeout period. The timeout period ranges from 1 minute to 4320 minutes. PPP IP Extension The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specially requires this setup, do not select it.
Use Static IP Address Unless your service provider specially requires this setup, do not select it. If selected, enter your static IP address. MTU This option allows us to change the MTU size for WAN interface, PPPoE and PPPoA. The default value is 1492 for PPPoE and 1500 for PPPoA. 2. Click Next to display the screen below. Enable IGMP Multicast checkbox: Tick the checkbox to enable IGMP multicast (proxy).
3. After entering your settings, select Next. The following screen appears. The Device Setup page allows the user to configure the LAN interface IP address, subnet mask and DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time.
4. Click Next to display the WAN Setup-Summary screen that presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. 5. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically.
5.2.2 MAC Encapsulation Routing (MER) To 1. 2. 3. configure MER, do the following. Select Quick Setup and click Next. Enter the PVC Index provided by the ISP and click Next and click Next Select the MAC Encapsulation Routing (MER) radio button, and click Next. The following screen appears. Enter information provided to you by your ISP to configure the WAN IP settings. Notice: DHCP Client can be enabled for PVC in MER mode if Obtain an IP address automatically is chosen.
4. Click Next to display the following screen appears. Enable NAT checkbox: If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side (i.e the LAN side is using a public IP), this checkbox should be de-selected.
5. Upon completion, click Next. The following screen appears. Note: If the NAT function is enabled, this DHCP Server Relay won’t be displayed as an option. The Device Setup page allows the user to configure the LAN interface IP address and DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time.
6. After entering your settings, select Next to display the following screen. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. The following screen will be displayed. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again.
5.2.3 IP Over ATM To 1. 2. 3. 4. configure IP Over ATM, Select Quick Setup and click Next. Enter the PVC Index and click Next. Type the VPI and VCI values provided by the ISP and click Next. Select the IP over ATM (IPoA) radio button and click Next. The following screen appears. Notice that DHCP is not supported over IPoA. The user must enter the IP address or WAN interface for the default gateway setup, and the DNS server addresses provided by the ISP. 5. Click Next. The following screen appears.
Enable NAT checkbox If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up. If a private IP address is not used on the LAN side (i.e the LAN side is using a public IP), this checkbox should be de-selected. When the system comes back after reboot, the NAT submenu will not be displayed on the left main panel.
The user must configure the IP Address and the Subnet Mask. To use the DHCP service on the LAN, select the Enable DHCP server checkbox, and enter the Start IP addresses, the End IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs. Select Enable DHCP Server Relay (if required), and enter the DHCP Server IP Address. Note that the router’s default IP address is 192.168.1.
8. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically. The CT-5611T is ready for operation and the LEDs display as described in the LED description tables.
5.2.4 Bridging Select the bridging mode. To configure Bridging, do the following. 1. 2. 3. 4. Select Quick Setup and click Next. Enter the PVC Index and click Next. Type in the VPI and VCI values provided by the ISP and click Next. Select the Bridging radio button and click Next. The following screen appears. To use the bridge service, tick the checkbox, Enable Bridge Service, and enter the service name. 5. Click the Next button to continue. Enter the IP address for the LAN interface.
6. Click the Next button The following screen will be displayed. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
Chapter 6 Advanced Setup This chapter explains: WAN, LAN, Routing, DSL and Port Mapping…... Note: Shown below for your reference are the available menu options for each different configuration. This screenshot is for PPPoE and PPPoA encapsulations. This screenshot is for Mer and IPoA encapsulations.
This screenshot is for Bridge encapsulation. 6.1 WAN VlanID • This function means one can add an 802.1Q VLAN tag on PPPoE/MER or Bridge mode. It means the packets are sent to WAN and a specific VlanID (802.1Q tag) will be added in the Ethernet header. The VlanID shows which 802.1Q tag will be added. For further information on WAN, please reference section: 4.1, Page 26.
6.2 LAN Configure the DSL Router IP Address and Subnet Mask for LAN interface. Save button only saves the LAN configuration data. Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable IGMP Snooping: Enable /Disable the function that is IGMP Snooping.
To configure a secondary IP address for the LAN port, click the box as shown below. IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port.
6.3 NAT To display the NAT function, you need to enable the NAT feature in the WAN Setup. 6.3.1 Virtual Servers Virtual Server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the Internal server with private IP address on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum 32 entries can be configured.
Select a Service Or Custom Server Server IP Address User should select the service from the list. Or User can enter the name of their choice. Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server). When a service is selected the port ranges are automatically configured. Enter the ending external port number (when you select Custom Server). When a service is selected the port ranges are automatically configured.
6.3.2 Port Triggering Some applications require that specific ports in the Router's firewall be opened for access by the remote parties. Port Trigger dynamically opens up the 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.
Select an Application Or Custom Application Trigger Port Start Trigger Port End Trigger Protocol Open Port Start Open Port End Open Protocol User should select the application from the list. Or User can enter the name of their choice. Enter the starting trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured. Enter the ending trigger port number (when you select custom application).
6.3.3 DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. Enter the computer's IP address and click "Apply" to activate the DMZ host. Clear the IP address field and click "Apply" to deactivate the DMZ host.
6.3.4 ALG SIP ALG is Application layer gateway. If the user has an IP phone(SIP) or VoIP gateway(SIP) behind the ADSL router, the SIP ALG can help VoIP packet passthrough the router (NAT enabled). Note: SIP (Session Initiation Protocol, RFC3261) is the protocol of choice for most VoIP (Voice over IP) phones to initiate communication. This ALG is only valid for SIP protocol running UDP port 5060.
6.4 Security To display the Security function, you need to enable the firewall feature in the WAN Setup. 6.4.1 IP Filtering IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. Click 'Save/Apply' to save and activate the filter. Outgoing Note: The default setting for Outgoing is Accepted.
Filter Name Protocol Source IP address Source Subnet Mask Source Port (port or port:port) Destination IP address Destination Subnet Mask Destination port (port or port:port) Type a name for the filter rule. User can select from: TCP, TCP/UDP, UDP or ICMP. Enter source IP address. Enter source subnet mask. Enter source port number. Enter destination IP address. Enter destination subnet mask. Enter destination port number. Incoming Note: The default setting for Incoming is Blocked.
To add a filtering rule, simply click the Add button. The following screen will be displayed. To configure the parameters, please reference Outgoing table above.
6.4.2 Parental Control Parental control: allows parents, schools, and libraries to set access times for Internet use. To add a parental control, simply click the Add button. The following screen will be displayed.
6.5 Quality of Service To display the Security function, you need to enable the QoS feature in the WAN Setup. Choose Add to configure network traffic classes.
Traffic Class Name Assign ATM Transmit Priority Mark IP Precedence Mark IP Type Of Service Mark 802.1p if 802.1q is enabled on WAN Physical LAN Port Protocol Source IP Address Source Subnet Mask UDP/TCP Source Port (port or port:port) Destination IP address Destination Subnet Mask UDP/TCP Destination port (port or port:port) 802.1p Priority Enter name for traffic class Select Low, Medium or High. Select between 1-7.
6.6 Routing The Routing dialog box allows you to configure Default gateway and Static Route. 6.6.1 Default Gateway If ‘Enable Automatic Assigned Default Gateway’ checkbox is selected, this router will accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the checkbox is not selected, enter the static default gateway AND/OR a WAN interface. Click 'Save/Apply' button to save it.
6.6.2 Static Route Choose Static Route to display the Static Route screen. The Static Route screen lists the configured static routes, and allows configuring static routes. Choose Add or Remove to configure the static routes. To add static route, click the Add button to display the following screen. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click Save/Apply to add the entry to the routing table.
6.7 DNS 6.7.1 DNS Server If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, enter the primary and optional secondary DNS server IP addresses. Click 'Save' button to save the new configuration. You must reboot the router to make the new configuration effective. 6.7.
To add a dynamic DNS service, simply click the Add button. The following screen will be displayed: D-DNS provider Hostname Interface Username Password Select a dynamic DNS provider from the list Enter the name for the dynamic DNS server. Select the interface from the list Enter the username for the dynamic DNS server. Enter the password for the dynamic DNS server.
6.8 DSL To access the DSL settings, First click On Advanced Setup and then click on DSL. The DSL Settings dialog box allows you to select an appropriate modulation mode. Option G.dmt Enabled Description Sets G.Dmt if you want the system to use G.Dmt mode. G.Lite Enabled T1.413 Sets G.Lite if you want the system to use G.Lite mode. Sets the T1.413 if you want the system to use only T1.413 mode. ADSL2 Enabled The device can support the functions of the ADSL2.
6.9 Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group. To add a port mapping group, simply click the Add button.
To create a group from the list, first enter the group name and then select from the available interfaces on the list. Automatically Add Clients With the Following DHCP Vendor IDs: Add support to automatically map LAN interfaces and USB to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Port Mapping is enabled. There are 4 PVCs (0/33, 0/36, 0/37, 0/38).
1. Default : ENET and USB. 2. Video: nas_0_36, nas_0_37 and nas_0_38. The DHCP vendor ID is "Video". The CPE's dhcp server is running on "Default". And ISP's dhcp server is running on PVC 0/36. It is for setup-box use only. In the LAN side, PC can get IP address from CPE's dhcp server and access Internet via PPPoE (0/33). If the setup-box was connected with interface "ENET" and send a dhcp request with vendor id "Video", CPE's dhcp server will forward this request to ISP's dhcp server.
6.10 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached on the certificate, indicating that these signers have verified that the owner information of this certificate is correct. 6.10.1 Local Click Create Certificate Request to generate a certificate signing request.
Click Apply to generate a private key and a certificate signing request. Certificate Name Common Name A user-defined name for the certificate. Usually, it is the fully qualified domain name for the machine. Organization Name The exact legal name of your organization. Do not abbreviate. State/Province Name The state or province where your organization is located. It cannot be abbreviated. Country/Region Name The two-letter ISO abbreviation for your country.
6.10.2 Trusted CA CA is the abbreviation for Certificate Authority. CA is a part of the X.509 system. It is itself a certificate, attached with the owner information of this certificate authority. But its purpose is not to do encryption/decryption. Its purpose is to sign and issue certificates; in order to prove the owner information of that certificate is correct. Click Import Certificate to paste the certificate content of your trusted CA.
Chapter 7 Diagnostics The Diagnostics menu provides feedback on the connection status of the CT-5611T and the ADSL link. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click Help and follow the troubleshooting procedures.
Chapter 8 Management The Management section of the CT-5611T supports the following maintenance functions and processes: • • • • • • • Settings System log TR-069 Client Internet Time Access Control Update software Save/Reboot 8.1 Settings The Settings option allows you to back up your settings to a file, retrieve the setting file, and restore the settings.
8.1.1 Configuration Backup The Backup option under Management>Settings, save your router configurations to a file on your PC. Click BACKUP Settings in the main window. You will be prompted to define the location of the backup file to save. After choosing the file location, click Backup Settings. Te file will then be saved to the assigned location. 8.1.2 Tools – Update Settings The Update option under Management>Settings update your router settings using your saved files.
8.1.3 Restore Default Clicking the Restore Default Configuration option in the Restore Settings screen can restore the original factory installed settings. NOTE: This entry has the same effect as the hardware reset-to-default button. The CT-5611T board hardware and the boot loader support the reset to default button. If the reset button is continuously pushed for more than 5 seconds, the boot loader will erase the entire configuration data saved on the flash memory.
8.2 System Log The System Log option under Management>Settings allows you to view the system events log, or to configure the System Log options. The default setting of system log is disabled. Follow the steps below to enable and view the system log. 1. Click Configure System Log to display the following screen. 2. Select from the desired Log options described in the following table, and then click Save/Apply.
Option Log Log level Display Level Mode Description Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled. To enable it, tick Enable and then Apply button. Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the CT-5611T SDRAM.
8.3 TR-069 Client WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Option Inform Inform Interval Description Disable/Enable TR-069 client on the CPE. The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method. ACS URL URL for the CPE to connect to the ACS using the CPE WAN Management Protocol.
Get RPC Methods This method may be used by a CPE or ACS to discover the set of methods supported by the ACS or CPE it is in communication with. This list may include both standard TR069 methods (those defined in this specification or a subsequent version) and vendor-specific methods. The receiver of the response MUST ignore any unrecognized methods. Click this button to force the CPE to immediately establish a connection to the ACS.
8.4 Internet Time The Internet Time option under Management menu bar configures the Modem’s time. To automatically synchronize with Internet timeservers, tick the corresponding box displayed on the screen. Then click Save/Apply. 8.5 Access Control The Access Control option under Management menu bar configures the accessrelated parameters, including three parts: Services, IP Address, and Passwords.
Note: LAN and WAN side are present on the screen if the WAN interface is UP. Only the LAN side will be displayed if the ADSL or WAN interface is down. 8.5.1 Services The Services option limits or opens the access services over the LAN or WAN. These services are provided FTP, HTTP, ICMP, SNMP, SSH (Security Socket Share), TELNET, and TFTP. Enable the service by checking the item in the corresponding checkbox, and then click Save/Apply.
8.5.2 Access IP Addresses The IP Addresses option limits the access by IP address. If the Access Control Mode is enabled, only the allowed IP addresses can access the router. Before you enable it, configure the IP addresses by clicking the Add button. Enter the IP address and click Apply to allow the PC with this IP address managing the DSL Router.
8.5.3 Passwords The Passwords option configures the access passwords for the router. Access to your DSL router is controlled through three user accounts: admin, support, and user. z z z “root” has unrestricted access to change and view configuration of your DSL Router. "support" is used to allow an ISP technician to access your DSL Router for maintenance and to run diagnostics. "user" can access the Router, view configuration settings and statistics, as well as, update the router's software.
8.6 Update Software The Update Software screen allows you to obtain an updated software image file from your ISP. Manual software upgrades from a locally stored file can be performed using the following screen. Step 1: Obtain an updated software image file from your ISP. Step 2: Enter the path to the image file location in the box below or click the Browse button to locate the image file. Step 3: Click the "Update Software" button once to upload the new image file.
8.7 Save and Reboot The Save/Reboot option saves the configurations and reboots the router. Close the DSL Router Configuration window and wait for 2 minutes before reopening your web browser. If necessary, reconfigure your PC's IP address to match your new configuration.
Appendix A: Pin Assignments Line port (RJ11) Pin 1 2 3 Definition ADSL_RING Pin 4 5 6 Definition ADSL_TIP - Pin Assignments of the RJ11 Port LAN Port (RJ45) Pin 1 2 3 4 Definition Transmit data+ Transmit dataReceive data+ NC Pin 5 6 7 8 Pin assignments of the LAN Port 96 Definition NC Receive dataNC NC
Appendix B: Specifications Rear Panel RJ-11 X1 for ADSL, RJ-45 X 1 for LAN, USB X 1 for LAN, Reset Button X 1, Power switch X 1 ADSL Standard ITU-T G.992.5, ITU-T G.992.3, ITU-T G.992.1, ANSI T1.413 Issue 2 G.992.5 (ADSL2+) Downstream : 24 Mbps Upstream : 1.3 Mbps G.992.3 (ADSL2) Downstream : 12 Mbps Upstream : 1.3 Mbps G.DMT Downstream: 8 Mbps Upstream: 832 Kbps Ethernet Standard 10/100 BaseT MDI/MDIX IEEE 802.3, IEEE 802.
Application Passthrough PPTP, L2TP, IPSec, VoIP, Yahoo messenger, ICQ, RealPlayer, NetMeeting, MSN, X-box, etc.
