CT-5072S ADSL2+ Router User Manual Version A2.
Preface This manual provides information related to the installation, operation, and application of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at INT-support@comtrend.com For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.
Table of Contents CHAPTER 1 INTRODUCTION...........................................................................................................4 1.1 FEATURES ........................................................................................................................................4 1.2 APPLICATION ...................................................................................................................................4 CHAPTER 2 INSTALLATION.........................................
8.1 SETTINGS .......................................................................................................................................59 8.1.1 Backup Settings...............................................................................................................59 8.1.2 Update Settings...............................................................................................................59 8.1.3 Restore Default .....................................................................
Chapter 1 Introduction CT-5072S with TR-069 compliant are a series of high performance ADSL2+ Ethernet Routers, providing one 10/100 Ethernet, and one ADSL line to access the Internet. Comtrend’s CT-5072S series also provide with TR-068 compliant panels and LED indicators making them more user-friendly. It incorporates LAN or Video on Demand over one ordinary telephone line at speeds of up to 24 Mbps.
Chapter 2 Installation 2.1 Hardware Setup Follow the instructions below to complete the hardware installation. The diagram below shows the back panel of the device. Power port Power button Reset button LINE Port Connect the ADSL line to this port with a RJ11 cable. LAN Port Use a RJ45 straight-through or crossover MDI/X cable to connect to the LAN. Power ON Press the power button to the OFF position (OUT). Connect the power adapter to the power port.
2.2 LED Indicators The LED indicators are shown below and explained in the table that follows. are useful for checking the power and connection status of the router.
Chapter 3 Web User Interface This section describes how to access the device via the web user interface (WUI) using an Internet browser such as Internet Explorer (version 5.0 and later). 3.1 Default Settings The factory default settings of this device are summarized below. • • • • LAN IP address: 192.168.1.1 LAN subnet mask: 255.255.255.
3.2 IP Configuration STATIC IP MODE To access router settings, your PC must have a static IP address within the 192.168.1.x subnet. Follow the steps below to configure your PC IP address to use subnet 192.168.1.x. The following steps assume you are running Windows XP. STEP 1: From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button.
DHCP MODE Set your PC to DHCP mode by selecting Obtain an IP address automatically in the Internet Protocol Properties dialog box, as shown below. 3.3 Login Procedure Perform the following steps to login to the web user interface. NOTE: The default settings can be found in section 3.1. STEP 1: Start the Internet browser and enter the default IP address for the device in the Web address field. For example, if the default IP address is 192.168.1.1, type http://192.168.1.1.
Click OK to continue. NOTE: The login password can be changed later (section 8.6.3 Passwords) STEP 3: After successfully logging in for the first time, you will reach this screen. NOTE1: If a PVC connection already exists then this Quick Setup screen will be bypassed and the Device Info – Summary screen will display instead. NOTE2: The selections available on the main menu (onscreen at left) are based upon the configured connection and user account privileges.
Chapter 4 Quick Setup The function allows the user to configure the ADSL router for DSL connectivity and Internet access. It guides the user though the WAN network setup first and then the LAN interface setup. The user can either manually customize the router or follow the auto quick setup procedure.
4.1 Auto Quick Setup The auto quick setup procedures require the ADSL link to be up to automatically detect PVCs. You simply need to follow the online instructions as prompted. Step 1: Select Quick Setup to display the DSL Quick Setup screen. Step 2: Click Next to start the setup process. Follow the online instructions to complete the setting. This procedure will skip some advanced setup procedures (such as PVC index and encapsulation selection).
4.2 Manual Quick Setup STEP 1: Click Quick Setup and un-tick the DSL Auto-connect checkbox ; to enable manual configuration of the connection type. Un-tick this checkbox to enable manual setup and display the following screen. STEP 2: Adjust the VPI/VCI settings for the connection you wish to establish. You may also Enable Quality of Service (QoS) with its checkbox ;. STEP 3: On this screen, you can choose the connection type and select the appropriate encapsulation mode. The available options are shown.
Click Next to continue… NOTE: The subsections that follow continue the ATM PVC setup procedure. Enter the appropriate settings for your service. Choosing different connection types will lead to a different sequence of setup screens.
4.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) STEP 4: Enter the PPP settings as provided by your ISP. PPP Settings The PPP Username, PPP password and the PPPoE Service Name entries are dependent on the particular requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. For Authentication Method, choose from AUTO, PAP, CHAP, and MSCHAP.
• • The device extends the IP subnet at the remote service provider to the LAN PC. i.e. the PC becomes a host belonging to the same IP subnet. The device bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the device’s LAN IP address. Use Static IP Address Unless your service provider specially requires this setup, do not select it. If selected, enter your static IP address in the IP Address field.
This screen allows for the configuration of the CT-5072S LAN interface IP address, subnet mask and DHCP server. To auto-assign IP addresses, DNS server and default gateway to other LAN devices, select the Enable DHCP server radio box. You must also enter the start and end IP address and DHCP leased time. To configure a secondary IP address for the LAN port, click the checkbox ; shown.
STEP 7: Click Next to display the configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. After clicking Save/Reboot, the router will save the configuration to the flash memory and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info screen automatically. The CT-5072S is ready for operation when the front panel LED indicators display as described in section 2.
4.2.2 MAC Encapsulation Routing (MER) STEP 4: Enter the WAN IP settings as provided by your ISP. DHCP can be enabled if the Obtain an IP address automatically checkbox ; is checked. Configuring the default gateway or the DNS with static values will disable the automatic assignment from DHCP or other WAN connection. STEP 5: Click Next to display the following screen. Enable NAT If the LAN is configured with a private IP address, the user should select this checkbox ;.
Enable Firewall If this checkbox ; is selected, the Security submenu will be displayed on the Advanced Setup menu after reboot. If firewall is not necessary, this checkbox ; should be de-selected to free up system resources for better performance. Enable IGMP Multicast Tick the checkbox ; to enable IGMP multicast (proxy). IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to report their multicast group memberships to any immediately neighboring multicast routers.
To configure a secondary IP address for the LAN port, click the checkbox ; shown. STEP 7: Click Next to display the configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. After clicking Save/Reboot, the router will save the configuration to the flash memory and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info screen automatically.
4.2.3 IP Over ATM STEP 4: Enter the WAN IP settings as provided by your ISP. Since DHCP is not supported over IPoA, the default gateway settings and DNS server addresses must be entered here. These should be provided by your ISP. STEP 5: Click Next to display the following screen. Enable NAT If the LAN is configured with a private IP address, the user should select this checkbox ;. The NAT submenu will appear in the Advanced Setup menu after reboot.
Enable IGMP Multicast Tick the checkbox ; to enable IGMP multicast (proxy). IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to report their multicast group memberships to any immediately neighboring multicast routers. Enable WAN Service Tick the checkbox ; to enable the WAN service. Service Name is user-defined. STEP 6: Upon completion, click Next. The following screen appears.
STEP 7: Click Next to display the configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. After clicking Save/Reboot, the router will save the configuration to the flash memory and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info screen automatically. The CT-5072S is ready for operation when the front panel LED indicators display as described in section 2.
STEP 5: Click Next to display the following screen. Enter the IP address and subnet mask for the LAN interface. These settings are used to manage the CT-5072S. In bridge mode, there is no WAN IP address and therefore no remote access to the router for technical support or other purposes. STEP 6: Click Next to display the configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
Chapter 5 Device Information The web user interface is divided into two windowpanes, the main menu (at left) and the display screen (on the right). The main menu has the several options and selecting each of these options opens a submenu with more selections. NOTE: The menu items shown are based upon the configured connection and user account privileges. For example, in the Advanced Setup menu, if NAT and Firewall are enabled, the main menu will display the NAT and Security submenus.
5.1 WAN Select WAN from the Device Info submenu to display the configured PVC(s). Heading VPI/VCI Con.
Heading Interface Received/Transmitted: 5.2.2 - Bytes Pkts Errs Drops Description LAN interface(s) Number of Bytes Number of Packets Number of packets with errors Number of dropped packets WAN Statistics Heading Service VPI/VCI Protocol Interface Received/Transmitted - Bytes - Pkts - Errs - Drops Description WAN service label ATM Virtual Path/Channel Identifiers Connection type (e.g.
5.2.3 ATM statistics The following figure shows the ATM statistics screen. ATM Interface Statistics Heading In Octets Out Octets Description Number of received octets over the interface Number of transmitted octets over the interface In Errors In Unknown Number of cells dropped due to uncorrectable HEC errors Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with invalid cell header patterns.
In Errors Out Errors In Discards Out Discards Number of received AAL5/AAL0 CPCS PDUs received that contain an error. These errors include CRC-32 errors. Number of received AAL5/AAL0 CPCS PDUs that could not be transmitted due to errors. Number of received AAL5/AAL0 CPCS PDUs discarded due to an input buffer overflow condition.
5.2.4 ADSL Statistics The following figure shows the ADSL Statistics screen in G.Dmt mode. Click the Reset Statistics button to refresh this screen.
Field Mode Type Line Coding Status Link Power State Description G.Dmt, G.lite, T1.413, ADSL2, ADSL2+ Channel type Interleave or Fast Trellis On/Off Lists the status of the DSL link Link output power state. SNR Margin (dB) Attenuation (dB) Signal to Noise Ratio (SNR) margin Estimate of average loop attenuation in the downstream direction. Total upstream output power The sync rate you would obtain. Current sync rate. Output Power (dBm) Attainable Rate (Kbps) Rate (Kbps) In G.
Within the ADSL Statistics window, a Bit Error Rate (BER) test can be started using the ADSL BER Test button. A small window will open when the button is pressed; it will appear as shown below. Click Start to start the test or Close. If the test is successful, the pop-up window will display as follows.
5.3 Route Choose Route to display the routes that the CT-5072S has found. Field Destination Gateway Subnet Mask Flag Metric Service Interface Description Destination network or destination host Next hub IP address Subnet Mask of Destination U: route is up !: reject route G: use gateway H: target is a host R: reinstate route for dynamic routing D: dynamically installed by daemon or redirect M: modified from routing daemon or redirect The 'distance' to the target (usually counted in hops).
5.4 ARP Click ARP to display the ARP information. Field IP address Flags HW Address Device Description Shows IP address of host pc Complete, Incomplete, Permanent, or Publish Shows the MAC address of host pc Shows the connection interface 5.5 DHCP Click DHCP to display all DHCP Leases.
Chapter 6 Advanced Setup This chapter explains the following screens: 6.1 WAN 6.6 Routing 6.2 LAN 6.7 DNS 6.3 NAT 6.8 DSL 6.4 Security 6.9 Certificate 6.5 Quality of Service 6.1 WAN This screen allows for the configuration of WAN interfaces. To Add a new WAN connection, click the Add button. To edit an existing connection, click the Edit button next to the connection. To complete the Add or Edit go to STEP 2 in section 4.2 Manual Quick Setup.
6.2 LAN From this screen, LAN interface settings can be configured. NOTE: NAT is enabled so UPnP is shown above (see underlined notes below). Consult the field descriptions below for more details. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable UPnP: Tick the box to enable Universal Plug and Play. This option is hidden when NAT disabled or if no PVC exists Enable IGMP Snooping: This function does not apply to this model.
IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port. NOTE: The Save button simply saves changes, while the Save/Reboot button both saves and reboots the device to make any changes effective. 6.3 NAT To display this option, NAT must be enabled in at least one PVC shown on the Advanced Setup - WAN screen. (NAT is not an available option in Bridge mode) 6.3.
Consult the table below for field and header descriptions. Field/Header Select a Service Or Custom Server Server IP Address External Port Start External Port End Protocol Internal Port Start Internal Port End Description User should select the service from the list. Or User can enter the name of their choice. Enter the IP address for the server. Enter the starting external port number (when you select Custom Server). When a service is selected, the port ranges are automatically configured.
6.3.2 Port Triggering Some applications require that specific ports in the firewall be opened for access by the remote parties. Port Triggers dynamically 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured.
Custom Application Trigger Port Start Trigger Port End Trigger Protocol Open Port Start Open Port End Open Protocol 6.3.3 User can enter the name of their choice. Enter the starting trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Enter the ending trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured. TCP, TCP/UDP, or UDP.
NOTE: This ALG is only valid for SIP protocol running on UDP port 5060. 6.4 Security To display this function, you must enable the firewall feature in WAN Setup. For detailed descriptions, with examples, please consult Appendix A – Firewall. 6.4.1 IP Filtering This screen sets filter rules that limit IP traffic (Outgoing/Incoming). Multiple filter rules can be set and each applies at least one limiting condition. For individual IP packets to pass the filter all conditions must be fulfilled.
To add a filter (to block some outgoing IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Save/Apply. Consult the table below for field descriptions. Field Filter Name Protocol Source IP address Source Subnet Mask Source Port (port or port:port) Destination IP address Destination Subnet Mask Destination Port (port or port:port) Description The filter rule label TCP, TCP/UDP, UDP, or ICMP. Enter source IP address. Enter source subnet mask.
For detailed field descriptions, please reference the previous table. Under WAN Interfaces, select the PVCs (All routing modes with firewall ON) where the filter rule will apply. You may select all PVCs or just a subset. Filter rules are arranged by PVC as shown under the VPI/VCI heading on the previous screen. 6.4.2 MAC Filtering NOTE: This option is only available in bridge mode. Other modes (i.e. PPPoE/A, IPoA, MER) use IP Filtering (pg. 42) to perform a similar function.
Choose Add or Remove to configure MAC filtering rules. The following screen will appear when you click Add. Create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them must be met. Click Save/Apply to save and activate the filter rule. Consult the table below for detailed field descriptions.
6.4.3 Parental Control This feature restricts access from a LAN device to an outside network through the device on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section 8.5 Internet Time, so that the scheduled times match your local time. Click Add to display the following screen. See below for field descriptions. Click Save/Apply to add a time restriction. User Name: A user-defined label for this restriction.
6.5 Quality of Service NOTE: QoS must be enabled in at least one PVC to display this option. (see Advanced Setup - WAN for further instructions). Choose Add to configure network traffic classes. The following screen will display. Field Traffic Class Name Assign ATM Transmit Priority Mark IP Precedence Description Enter name for traffic class. Select Low, Medium or High. Select between 0-7. The lower the digit shows the higher the priority.
Mark IP Type Of Service Mark 802.1p if 802.1q is enabled on WAN SET-1 Protocol Source IP Address Source Subnet Mask UDP/TCP Source Port (port or port:port) Destination IP address Destination Subnet Mask UDP/TCP Destination port (port or port:port) SET-2 802.1p Priority Normal Service, Minimize Cost, Maximize Reliability, Maximize Throughput, Minimize Delay Select between 0-7. The higher the digit shows the higher the priority. TCP, TCP/UDP, UDP, or ICMP. Enter the source IP address.
Assign Differentiated Services Code Point (DSCP) Mark Source MAC Address Source MAC Mask Destination MAC Address Destination MAC Mask The selected Code Point gives the corresponding priority to the packets that satisfies the rules set below. A packet belongs to SET-1, if a binary-AND of its source MAC address with the Source MAC Mask is equal to the binary-AND of the Source MAC Mask and this field. This is the mask used to decide how many bits are checked in Source MAC Address.
6.6.2 Static Route This option allows for the configuration of static routes. Click Add to create a new static route. Click Remove to delete the selected static route. Click the Add button to display the following screen. Enter Destination Network Address, Subnet Mask, Gateway IP Address, and/or WAN Interface. Then click Save/Apply to add the entry to the routing table. 6.6.3 RIP To activate RIP, select the Enabled radio button for Global RIP Mode.
6.7 DNS 6.7.1 DNS Server If the Enable Automatic Assigned DNS checkbox ; is selected, this router will accept the first received DNS assignment from one of the DHCP enabled PVC(s). If the checkbox ; is not selected, enter the primary and optional secondary DNS server IP addresses. Click Save to save the new configuration. NOTE: You must reboot the router to make the new configuration effective. 6.7.
To add a dynamic DNS service, click Add. The following screen will display. Consult the table below for field descriptions.
6.8 DSL The DSL Settings screen allows for the selection of DSL modulation modes. For optimum performance, the modes selected should match those of your ISP. DSL Mode G.Dmt G.lite T1.413 ADSL2 AnnexL ADSL2+ AnnexM Options Inner/Outer Pair Bitswap Enable SRA Enable Data Transmission Rate - Mbit/s (Megabits per second) Downstream: 12 Mbit/s Upstream: 1.3 Mbit/s Downstream: 4 Mbit/s Upstream: 0.5 Mbit/s Downstream: 8 Mbit/s Upstream: 1.0 Mbit/s Downstream: 12 Mbit/s Upstream: 1.
6.9 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached to the certificate, indicating that these entities have verified that this certificate is valid. 6.9.1 Local CREATE CERTIFICATE REQUEST Click Create Certificate Request to generate a certificate-signing request.
Field Certificate Name Common Name Organization Name State/Province Name Country/Region Name Description A user-defined name for the certificate. Usually, the fully qualified domain name for the machine. The exact legal name of your organization. Do not abbreviate. The state or province where your organization is located. It cannot be abbreviated. The two-letter ISO abbreviation for your country.
6.9.2 Trusted CA CA is an abbreviation for Certificate Authority, which is a part of the X.509 system. It is itself a certificate, attached with the owner information of this certificate authority; but its purpose is not encryption/decryption. Its purpose is to sign and issue certificates, in order to prove that these certificates are valid. Click Import Certificate to paste the certificate content of your trusted CA.
Chapter 7 Diagnostics Diagnostics screens for PPPoE and Bridge connection types are shown below. PPPoE Connection Bridge Connection General Information The Diagnostics menu provides feedback on the connection status of the device. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of the screen to retest and confirm the error. If the test continues to fail, click Help and follow the troubleshooting procedures.
Test ENET Connection ADSL Synchronization Description Pass: Indicates that the CT-5072S has interface on your computer. Fail: Indicates that the CT-5072S does interface on your computer. Pass: Indicates that the CT-5072S has from the telephone company. Fail: Indicates that the CT-5072S does from the telephone company.
Chapter 8 Management The Management menu has the following maintenance functions and processes: 8.1 Settings 8.5 Internet Time 8.2 System Log 8.6 Access Control 8.3 SNMP Agent 8.7 Update Software 8.4 TR-069 Client 8.8 Save and Reboot 8.1 Settings This includes Backup Settings, Update Settings, and Restore Default screens. 8.1.1 Backup Settings To save the current configuration to a file on your PC, click Backup Settings. You will be prompted for a location of the backup file.
8.1.3 Restore Default Click Restore Default Settings to restore the CT-5072S to factory default settings. After Restore Default Settings is clicked, the following screen appears. Close the browser and wait for 2 minutes before reopening it. It may also be necessary, to reconfigure your PC IP configuration to match your new settings. NOTE: This entry has the same effect as the Reset button. The CT-5072S board hardware and the boot loader support the reset to default.
8.2 System Log This function allows a system log to be kept and viewed upon request. Follow the steps below to configure, enable, and view the system log. Step 1: Click Configure System Log as shown below. Step 2: Select desired options and click Save/Apply. Consult the table below for detailed descriptions of each system log option. Option Description Log Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled.
By default, the log level is “Debugging”, which is the lowest critical level.
8.4 TR-069 Client WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Option Inform Inform Interval ACS URL ACS User Name Description Disable/Enable TR-069 client on the CPE. The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method. URL for the CPE to connect to the ACS using the CPE WAN Management Protocol.
ACS Password Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE. Connection Request User Name Username used to authenticate an ACS making a Connection Request to the CPE. Password Password used to authenticate an ACS making a Connection Request to the CPE. The Get RPC Methods button forces the CPE to establish an immediate connection to the ACS.
NOTES - 1. The WAN column only appears if a WAN connection is configured. 2. Appendix D contains a quick introduction to one SSH client. 8.6.2 IP Addresses This option limits access to the router by IP address. When Access Control Mode is enabled, only the IP addresses listed here can access the router. Before enabling Access Control Mode, configure the IP addresses by clicking the Add button.
8.6.3 Passwords This screen is used to configure the user account access passwords for the device. Access to the CT-5072S is controlled through the following three user accounts: • • • root - this has unrestricted access to change and view the configuration. support - used for remote maintenance and diagnostics of the router user - this has limited access. This account can view configuration settings and statistics, as well as, update the router firmware.
8.7 Update Software This option allows for firmware upgrades from a locally stored file. Step 1: Obtain an updated software image file from your ISP. Step 2: Enter the path and filename of the firmware image file in the Software File Name field or click the Browse button to locate the image file. Step 3: Click the Update Software button once to upload and install the file. NOTE: The update process will take about 2 minutes to complete.
Appendix A – Firewall STATEFUL PACKET INSPECTION Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. DENIAL OF SERVICE ATTACK Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
irrespective of the destination. All other packets will be Accepted. Example 2: Filter Name Protocol Source Address Source Subnet Mask Source Port Dest. Address Dest. Subnet Mask Dest. Port : : : : : : : : Out_Filter2 UDP 192.168.1.45 255.255.255.0 5060:6060 172.16.13.4 255.255.255.0 6060:7070 This filter will drop all UDP packets coming from the LAN with IP Address / Subnet Mask of 192.168.1.45/24 and a source port range of 5060 to 6060, destined to 172.16.13.
on this interface are DROPPED. Example 2: Filter Name Protocol Source Address Source Subnet Mask Source Port Dest. Address Dest. Sub. Mask Dest. Port : : : : : : : : In_Filter2 UDP 210.168.219.45 255.255.0.0 5060:6060 192.168.1.45 255.255.255.0 6060:7070 This rule will ACCEPT all UDP packets coming from WAN interface mer_0_35/nas_0_35 with IP Address/Subnet Mask 210.168.219.45/16 and a source port in the range of 5060 to 6060, destined to 192.168.1.
Example 2: Global Policy : Protocol Type : Dest. MAC Address : Source MAC Address : Frame Direction : WAN Interface Selected : Blocked PPPoE 00:12:34:56:78:90 00:34:12:78:90:56 WAN => LAN br_0_34/nas_0_34 Addition of this rule forwards all PPPoE frames going from WAN to LAN with a Destination MAC Address of 00:12:34:56:78 and Source MAC Address of 00:34:12:78:90:56 on the br_0_34 WAN interface. All other frames on this interface are dropped.
Appendix B – Pin Assignments LINE PORT (RJ11) Pin 1 2 3 Definition ADSL_RING Pin 4 5 6 Definition ADSL_TIP - LAN Port (RJ45) Pin 1 2 3 4 Definition Transmit data+ Transmit dataReceive data+ NC Pin 5 6 7 8 72 Definition NC Receive dataNC NC
Appendix C – Specifications Hardware Interface RJ-11 X1 for ADSL2+, RJ-45 X 1 for LAN, Power Switch X 1, Power Jack X 1, Reset Button X 1 WAN Interface ITU-T G.994.1/G.992.5/G.992.3/G.992.2/G.992.1, ANSI T1.413 Issue 2 G.992.5 (ADSL2+) ........Downstream : 24 Mbps Upstream : 1.3 Mbps G.992.3 (ADSL2)...........Downstream : 12 Mbps Upstream : 1.3 Mbps Auto-negotiation rate adaptation G.DMT / G.lite Annex M LAN Interface Standard......................IEEE 802.3, IEEE 802.3u 10/100 BaseT ...............
Application Passthrough PPTP, L2TP, IPSec, VoIP, Yahoo messenger, ICQ, RealPlayer, NetMeeting, MSN, X-box Power Supply ................................................Input: 100 - 240 Vac Output: 18 Vdc / 300 mA Environment Condition Operating temperature ...........................0 ~ 50 degrees Celsius Relative humidity ...................................5 ~ 95% (non-condensing) Dimensions .......................................
Appendix D – SSH Client Unlike Microsoft Windows, Linux OS has a ssh client included. For Windows users, there is a public domain one called “putty” that can be downloaded from here: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the ssh client you must first enable SSH access for the LAN or WAN from the Management Æ Access Control Æ Services menu in the web user interface. To access the router using the Linux ssh client For LAN access, type: ssh -l root 192.168.1.
