User guide

vi Vipersat CDM-570/570L User Guide
Figure 3-62 DPC Configuration screen (SCPC
mode). . . . . . . . . . . . . . . . . . . . . . . . . . 3-49
Figure 3-63 Maximum Power Level prompt (CDM-
570L) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50
Figure 3-64 Minimum Power Level prompt (CDM-
570L) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50
Figure 3-65 Target EbNo prompt . . . . . . . . . . 3-51
Figure 3-66 Target Range prompt . . . . . . . . . 3-51
Figure 3-67 Speed Up EbNo prompt . . . . . . . 3-52
Figure 3-68 Target DPC Address prompt. . . . 3-52
Figure 3-69 Home State Configuration screen3-54
Figure 3-70 Force Modem to Home State warning
3-55
Figure 3-71 Transmit Frequency prompt . . . . 3-55
Figure 3-72 Transmit Data Rate prompt. . . . . 3-56
Figure 3-73 Transmit FEC Type prompt. . . . . 3-56
Figure 3-74 Transmit Coding Rate prompt . . . 3-56
Figure 3-75 Transmit Modulation Type prompt3-57
Figure 3-76 Transmit Power Level prompt . . . 3-57
Figure 3-77 Receive Frequency prompt . . . . . 3-58
Figure 3-78 Receive Data Rate prompt . . . . . 3-58
Figure 3-79 Receive FEC Type prompt . . . . . 3-58
Figure 3-80 Receive Coding Rate prompt . . . 3-59
Figure 3-81 Receive Modulation Type prompt3-59
Figure 3-82 Vipersat Summary screen (Hub). 3-60
Figure 3-83 Vipersat Migration prompt . . . . . . 3-61
Figure 3-84 UDP Port Base Address prompt . 3-61
Appendix A Figures
Figure A-1 The Seven OSI Protocol Layers . . .A-2
Figure A-2 Bits and Bytes. . . . . . . . . . . . . . . . .A-4
Figure A-3 Binary to Decimal Conversion . . . .A-4
Figure A-4 IP Address Classes A, B, C . . . . . .A-7
Figure A-5 NAT Router Example . . . . . . . . . . .A-8
Figure A-6 Default Subnet Masks for IP Classes .
A-9
Figure A-7 ANDing an IP address and a subnet
mask . . . . . . . . . . . . . . . . . . . . . . . . . .A-10
Figure A-8 Network Segments . . . . . . . . . . . .A-10
Figure A-9 Router as Default Gateway. . . . . .A-11
Figure A-10 Network Node MAC Addresses .A-12
Appendix B Figures
Figure B-1 Auto Switching menu (Hub) . . . . . .B-5
Figure B-2 Auto Switching menu (Remote) . . B-7
Figure B-3 Load Switching diagram . . . . . . . . B-9
Figure B-4 Application Switching diagram . . B-11
Figure B-5 ECM Switch Recovery: < 3 minutes . .
B-15
Figure B-6 ECM Switch Recovery: > 3 minutes . .
B-16
Appendix C Figures
Figure C-1 DPC Scaling Function. . . . . . . . . . C-6
Appendix D Figures
Figure D-1 Firmware Migration Stages—CDM-570
D-4
Figure D-2 Main Menu, Telnet . . . . . . . . . . . . D-5
Figure D-3 Operations and Maintenance MenuD-5
Figure D-4 Initial Vload screen . . . . . . . . . . . . D-6
Figure D-5 Add All dialog . . . . . . . . . . . . . . . . D-6
Figure D-6 Get Information for IP Address . . . D-7
Figure D-7 Put Application screen (Consecutive
Load) . . . . . . . . . . . . . . . . . . . . . . . . . . D-8
Figure D-8 Progress Status, Put Application . D-9
Figure D-9 Hard Reset screen . . . . . . . . . . . D-10
Figure D-10 Progress Status, Put CompletionD-10
Figure D-11 Unit Information screen (Router) D-11
Figure D-12 Select Configuration screen . . . D-11
Figure D-13 Configuration File Text . . . . . . . D-12
Figure D-14 Browse for Firmware File . . . . . D-12
Figure D-15 Download v1.4.5 and Hard Reset
screen . . . . . . . . . . . . . . . . . . . . . . . . D-13
Figure D-16 Unit Information screen (Base Modem
Image 1). . . . . . . . . . . . . . . . . . . . . . . D-13
Figure D-17 Download v1.5.1 and Hard Reset
screen . . . . . . . . . . . . . . . . . . . . . . . . D-14
Figure D-18 Unit Information screen (Base Modem
Image 2). . . . . . . . . . . . . . . . . . . . . . . D-14
Figure D-19 Unit Information screen (Base Modem
v1.5.1) . . . . . . . . . . . . . . . . . . . . . . . . D-15
Figure D-20 Unit Information screen (final status)
D-15
Figure D-21 Main Menu screen, CLI. . . . . . . D-16
Figure D-22 Vipersat Configuration screen . D-17
Figure D-23 Vipersat Migration prompt. . . . . D-17