Specifications

Page 8 of 28
Spectrum Master™ MS2712E and MS2713E Specifications
LTE Signal Analyzers (Options 0541, 0542, 0546, 0551, 0552, 0556)
Measurements
RF
(Option 0541 FDD)
(Option 0551 TDD)
Modulation
(Option 0542 FDD)
(Option 0552 TDD)
Over-the-Air (OTA)
(Option 0546 FDD)
(Option 0556 TDD)
Pass/Fail
(User Editable)
Channel Spectrum
Channel Power
Occupied Bandwidth
Power vs. Time (TDD only)
Frame View
Sub-Frame View
Total Frame Power
DwPTS Power
Transmit Off Power
Cell ID
Timing Error
ACPR
Spectral Emission Mask
Category A or B (Opt 1)
RF Summary
Power vs. Resource Block (RB)
RB Power (PDSCH)
Active RBs, Utilization %
Channel Power, Cell ID
OSTP, Frame EVM by
modulation (FDD only)
Constellation
QPSK, 16 QAM, 64 QAM
Modulation Results
Ref Signal Power (RS)
Sync Signal Power (SS)
EVM – rms, peak, max hold
Frequency Error – Hz, ppm
Carrier Frequency
Cell ID
Control Channel Power
Bar Graph or Table View
RS, P-SS, S-SS
PBCH, PCFICH, PHICH, PDCCH
Total Power (Table View)
EVM
Modulation Results
Tx Time Alignment
Modulation Summary
Includes EVM by modulation
(FDD only)
Antenna Icons
Detects active antennas (1/2)
Scanner
Cell ID (Group, Sector)
S-SS Power, RSRP, RSRQ, SINR
Dominance
Modulation Results – On/Off
Tx Test
Scanner
RS Power of MIMO antennas
Cell ID, Average Power
Delta Power (Max-Min)
Graph of Antenna Power
Modulation Results – On/Off
Mapping
On-screen
S-SS Power, RSRP, RSRQ,
or SINR
Scanner
Modulation Results – Off
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
ACLR
Frequency Error
Carrier Frequency
Dominance
EVM peak, rms
RS Power
RS EVM (FDD only)
SS, P-SS, S-SS Power
SS, P-SS, S-SS EVM (FDD only)
PBCH Power
PBCH EVM (FDD only)
PCFICH Power
PCFICH EVM (FDD only)
PHICH Power, EVM (FDD only)
PDCCH Power, EVM (FDD only)
Cell, Group, Sector ID
OSTP (FDD only)
Tx Time Alignment (FDD only)
Frame Power (TDD only)
DWPTS Power (TDD only)
Transmit Off Power (TDD only)
Timing Error (TDD only)
Setup Parameters
Frequency E-UTRA FDD bands 1 - 5, 7 - 14, 17 - 21, 23 - 25 (tunable 10 MHz to 4.0 GHz)
E-UTRA TDD bands 33 - 43 (tunable 10 MHz to 4.0 GHz)
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Bandwidth 1.4, 3, 5, 10, 15, 20 MHz
Span Auto, 1.4, 3, 5, 10, 15, 20, 30 MHz
Amplitude Scale/Division, Power Offset, Auto Range, Adjust Range
Sweep Single/Continuous, Trigger Sweep
EVM Mode Auto, PBCH only
Save/Recall Setup, Measurement, Screen Shot (save only), to Internal/External Memory
Measurement Summary Screens Overall Measurements, RF Measurements, Signal Quality Measurements
RF Measurements (Options 0541, 0551)
RF Channel Power Accuracy ± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +10 dBm) (Option 0541)
± 1.5 dB, ± 1.0 dB typical, (RF input –30 dBm to +10 dBm) (Option 0551)
Modulation Measurements (Options 0542, 0552)
Frequency Error ± 10 Hz + time base error, 99% condence level
Residual EVM (rms)
(FDD only)
2.0% typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm) for BW ≤ 10 MHz
2.5% typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm) for BW > 10 MHz
Residual EVM (rms)
(TDD only)
2.0% typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm) for BW ≤ 10 MHz
2.5% typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm) for BW > 10 MHz
Over-the-Air (OTA) Measurements (Options 0546, 0556)
Scanner Six strongest signals if present
Auto Save – Sync Signal Power and Modulation Results with GPS tagging
Auto Save Scanner – three strongest signals if present
RS Power – strongest signal
Mapping Map On-screen S-SS Power, RSRP, RSRQ, or SINR of Cell ID with strongest signal
Scanner – three strongest signals if present
Save and Export Scanner data: *.kml, *.mtd (tab delimited)
ООО "Техэнком" Контрольно-измерительные приборы и оборудование www.tehencom.com