Datasheet

Page 8 of 28
Spectrum Master™ MS2712E and MS2713E Specifications
LTE Signal Analyzers (Options 0541, 0542, 0546, 0551, 0552, 0556)
Measurements
RF
(Option 0541 FDD)
(Option 0551 TDD)
Modulation
(Option 0542 FDD)
(Option 0552 TDD)
Over-the-Air (OTA)
(Option 0546 FDD)
(Option 0556 TDD)
Pass/Fail
(User Editable)
Channel Spectrum
Channel Power
Occupied Bandwidth
Power vs. Time (TDD only)
Frame View
Sub-Frame View
Total Frame Power
DwPTS Power
Transmit Off Power
Cell ID
Timing Error
ACPR
Spectral Emission Mask
Category A or B (Opt 1)
RF Summary
Power vs. Resource Block (RB)
RB Power (PDSCH)
Active RBs, Utilization %
Channel Power, Cell ID
OSTP, EVM (FDD only)
Constellation
QPSK, 16 QAM, 64 QAM
Modulation Results
Ref Signal Power (RS)
Sync Signal Power (SS)
EVM – rms, peak, max hold
Frequency Error – Hz, ppm
Carrier Frequency
Cell ID
Control Channel Power
Bar Graph or Table View
RS, P-SS, S-SS
PBCH, PCFICH
Total Power (Table View)
Modulation Results
Modulation Summary
Includes EVM by modulation
(FDD only)
Antenna Icons
Detects active antennas (1/2)
Scanner
Cell ID (Group, Sector)
S-SS Power, RSRP, RSRQ, SINR
Dominance
Modulation Results – On/Off
Tx Test
Scanner
RS Power of MIMO antennas
Cell ID, Average Power
Delta Power (Max-Min)
Graph of Antenna Power
Modulation Results – On/Off
Mapping
On-screen
S-SS Power, RSRP, RSRQ,
or SINR
Scanner
Modulation Results – Off
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
ACLR
Frequency Error
Carrier Frequency
Dominance
EVM peak, rms
RS Power
SS, P-SS, S-SS Power
PBCH Power
PCFICH Power
Cell, Group, Sector ID
Frame Power (TDD only)
DWPTS Power (TDD only)
Transmit Off Power (TDD only)
Timing Error (TDD only)
Setup Parameters
Frequency E-UTRA FDD bands 1 - 5, 7 - 14, 17 - 21, 23 - 25 (tunable 10 MHz to 4.0 GHz)
E-UTRA TDD bands 33 - 43 (tunable 10 MHz to 4.0 GHz)
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Bandwidth 1.4, 3, 5, 10, 15, 20 MHz
Span Auto, 1.4, 3, 5, 10, 15, 20, 30 MHz
Amplitude Scale/Division, Power Offset, Auto Range, Adjust Range
Sweep Single/Continuous, Trigger Sweep
EVM Mode Auto, PBCH only
Save/Recall Setup, Measurement, Screen Shot (save only), to Internal/External Memory
Measurement Summary Screens Overall Measurements, RF Measurements, Signal Quality Measurements
RF Measurements (Options 0541, 0551)
RF Channel Power Accuracy ± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +10 dBm) (Option 0541)
± 1.5 dB, ± 1.0 dB typical, (RF input –30 dBm to +10 dBm) (Option 0551)
Modulation Measurements (Options 0542, 0552)
Frequency Error ± 10 Hz + time base error, 99% condence level
Residual EVM (rms)
(FDD only)
2.0% typical (E-UTRA Test Model 3.1, RF Input -50 dBm to +10 dBm) for BW ≤ 10 MHz
2.5% typical (E-UTRA Test Model 3.1, RF Input -50 dBm to +10 dBm) for BW > 10 MHz
Residual EVM (rms)
(TDD only)
2.0% typical (E-UTRA Test Model 3.1, RF Input -30 dBm to +10 dBm) for BW ≤ 10 MHz
2.5% typical (E-UTRA Test Model 3.1, RF Input -30 dBm to +10 dBm) for BW > 10 MHz
Over-the-Air (OTA) Measurements (Options 0546, 0556)
Scanner Six strongest signals if present
Auto Save – Sync Signal Power and Modulation Results with GPS tagging
Auto Save Scanner – three strongest signals if present
RS Power – strongest signal
Mapping Map On-screen S-SS Power, RSRP, RSRQ, or SINR of Cell ID with strongest signal
Scanner – three strongest signals if present
Save and Export Scanner data: *.kml, *.mtd (tab delimited)