User's Manual

ManualsBrandsComputime ManualsElectronicsTouch Screen Transmitter

MHSC Touch Screen Full Function Signature Command Operating Instructions

Touch Screen Full Function Signature Command Operating Instructions

Page: 1

Touch Screen Full Function Signature Command (TSFSC)

OPERATING INSTRUCTIONS

This remote control transmitter provides a multifunctional, reliable and user-friendly remote control for the

signature command system. The transmitter can be manually or thermostatically turned the system on and off.

Always check the appliance home owner’s manual for additional information, or warnings regarding accessory

installation before using this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact

the dealer from whom you purchased the kit or Ambient Technologies Technical Support at 1 800 398 6195.

Do not attempt to install any part of the kit unless all parts are in good condition. Please keep this booklet for

future reference.

CONTENTS OF KIT

Description Qty

Transmitter 1

Mounting Base 1

Battery Alkaline AAA 4

Instructions 1

#6 ¾” Screws, Zinc 2

FEATURES

• Large LCD display

•

Touch Screen Panel

•

Thermostatic Control Mode with Smart Mode Option

• Timer Mode

•

Sleep Mode to Save Battery

• Slide Function for Fast Operation

•

Three Flame Height Settings

•

Three Brightness Settings for Lights

• Three Speed Control for Blower

•

Auxiliary Control

• Low battery Indication

•

Child Proof Lock-out

•

Programmable Timer to turn blower on and off

• LCD Backlight

•

On-screen Security Codes Setup

Summary of content (9 pages)

PAGE 1
MHSC Touch Screen Full Function Signature Command Operating Instructions Touch Screen Full Function Signature Command (TSFSC) OPERATING INSTRUCTIONS This remote control transmitter provides a multifunctional, reliable and user-friendly remote control for the signature command system. The transmitter can be manually or thermostatically turned the system on and off.
PAGE 2
MHSC Touch Screen Full Function Signature Command Operating Instructions Function Areas of the LCD Display The figure on the right shows a typical display of the TSFSC LCD. Information Bar The information bar shows the room temperature, the “sending signal” radio icon, the low battery indication icon, the child-proof icon, and the flame icon. This area doesn’t have touch buttons. - - The room temperature will always be shown after power-up. It displays the room temperature from 40 °F to 99 °F.
PAGE 3
MHSC NOTE Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the transmitter to stabilize to room temperature before accurate room temperatures are displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for accurate temperature readings to appear on the LCD display.
PAGE 4
MHSC Touch Screen Full Function Signature Command Operating Instructions The Signature Command control board then needs to re-learn the new setting. 1. The RF receiver button on the control board must be in the on position before the learn function can begin. Use paper clip to depress the recessed button, one beep for RF receiver ON or two beeps for RF receiver OFF. 2. Holding the OFF button on the Command Center while turning on the master switch will activate the learn function for the transmitter. 3.
PAGE 5
MHSC Touch Screen Full Function Signature Command Operating Instructions The transmitter will operate the remote receiver from 1foot to a maximum of 30 feet. The distance is reduced when batteries are low. Manual Mode In this mode, the TIMER button and the THERMO button will only display “TIMER” and “THERMO”, respectively, without showing the time and the Set temperature.
PAGE 6
MHSC Touch Screen Full Function Signature Command Operating Instructions 3. Press the THERMO button again to confirm the Set Temperature. The transmitter will send out an On signal or an Off signal depending on the relationship between the Set temperature and the Room temperature. The flashing stops and the ON/up and OFF/down buttons become flame height controller again. The flame height will then stay as set up by the ON/up and OFF/down buttons.
PAGE 7
MHSC Touch Screen Full Function Signature Command Operating Instructions Light Brightness Control The light brightness control function is used to adjust the brightness of the light bulbs connected to the AC module on the Signature Command System. There are four light brightness levels defined: Off, Low, Medium and High. 1. Press the LIGHT button to enter the light brightness control mode. The LIGHT icon will start flashing. 2.
PAGE 8
MHSC Touch Screen Full Function Signature Command Operating Instructions Safety Features 1. Low Battery Detection When low battery condition occurs, the transmitter will turn off the fireplace. A) Battery voltage is checked every one minute. When the battery voltage is low, the LCD displays a low battery icon which will exist in all modes. B) The transmitter will not operate with low battery voltage. Change the batteries before the batteries become too weak for normal operations. 2.
PAGE 9
MHSC 6. Blower is not on after the fireplace is turned on Touch Screen Full Function Signature Command Operating Instructions 4. Distance between the transmitter and receiver is more than 30 feet 1. Blower setting is off 2. Blower delay setting is set too high 1. Make sure the operating distance is less than 30 feet 1. Press FAN key to select Fan speed you desire. 2. Press and hold FAN key to set desired ON/OFF delays. This is done in minutes.