User's Manual

ManualsBrandsComputime ManualsElectronicsRemote Control

50D0098 RCSITE Installation & Operating Manual

Rel 0 Dec 2005

Page 1 of 10

Ambient Technologies

A Division Of Monessen Hearth Systems

RCSIT

Thermostatic On/Off, Flame Height Adjustment

Remote Control for S.I.T 820 Valve (with Stepper Motor)

INSTALLATION AND OPERATING INSTRUCTIONS

This remote control system provides a safe, reliable and user-friendly remote control for millivolt valve gas

appliances, and flame height adjustment. The system can be manually or thermostatically turned on and off with the

transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding

accessory installation before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the

dealer from whom you purchased the kit or Ambient Technologies Technical Support at 1 800 398 6195. Do not

attempt to install any part of the kit unless all parts are in good condition. Please keep this booklet for future

reference.

CONTENTS OF KIT

Description Qty

Transmitter 1

Battery Alkaline AAA (for Transmitter) 3

Receiver (Assembly) consists of : 1

Receiver Box

Battery Alkaline AA 4

Slide Button-Black (On/RS/Off) 1

Plug-In Wiring Assembly for SIT mV Valve– 22” Inches 1

Plug-In Wiring Assembly for SIT Hi/Lo Regulator – 10” Inches 1

Velcro (Loop and Hook) 1

Installation Instructions 1

#6 ¾” Screws, Zinc 2

FEATURES/SPECIFICATIONS

• Thermostatic Control

• Battery Powered Transmitter & Receiver

• Easy Battery Access

• Low battery Indication for Transmitter and receiver

• Battery Powered Receiver

• Three Flame Height Setting

• Child Proof Lock-out

• 16 Security Codes

• 6 hour Shut Down (Optional) on receiver

• Quick Disconnect Wiring Assembly

• Reset Button for transmitter

Summary of content (9 pages)

PAGE 1
RCSIT Thermostatic On/Off, Flame Height Adjustment Remote Control for S.I.T 820 Valve (with Stepper Motor) INSTALLATION AND OPERATING INSTRUCTIONS This remote control system provides a safe, reliable and user-friendly remote control for millivolt valve gas appliances, and flame height adjustment. The system can be manually or thermostatically turned on and off with the transmitter.
PAGE 2
WARNING Important Safety Information • • • • • NOTE Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the transmitter to stabilize to room temperature before accurate room temperatures are displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for accurate temperature readings to appear on the LCD display. WARNING Turn appliance OFF and allow to cool before installing or servicing.
PAGE 3
INSTALLATIONS Remote Receiver: The remote receiver may be installed in the appliance per the appliance homeowner’s manual. Refer to the Homeowner’s Manual for special installation instructions. Failure to follow the installation instructions found in the appropriate Homeowner’s Manual will void the warranty and may cause a fire hazard. This system comes with an 22 inch two-wire assembly labled “FOR MILLVOLT VALVE ONLY, TP/TH”and an 10 inch four-wire assembly labeled “SIT VALVE ONLY”.
PAGE 4
Remote Transmitter : Battery Door Tab Installing Batteries: The remote transmitter uses three (3) “AAA”batteries. To install batteries, 1. 2. 3. 4. 5. Press down the battery door tab and pull out to remove the battery door. Install the batteries as indicated on transmitter. Close the battery door by snapping in place. When three batteries are installed, the transmitter will initialize for 10 seconds and then is ready for use.
PAGE 5
WARNING Do not use two (2) or more remote control systems in the same area with the same dip switch settings, as they will communicate with each other. This may cause the appliances to malfunction. Reset Button: The reset button can be used to reset the transmitter if transmitter is not working properly. The reset button is located behind the battery door cover in the lower left corner of battery comparment.
PAGE 6
Manual Mode: 1. Press the ON button once to turn on the appliance with max flame height. 2. Press the OFF button to decrease flame height. The first two pressing will decrease flame height to lower level. The third pressing will turn fireplace off. 3. If holding on OFF button for more than 3 second, fireplace will be shut off. Thermostatic Mode: 1. 2. 3. 4. 5. Press the AUTO button to enter the thermostatic mode.
PAGE 7
Child-Proof Protection: 1. Press and hold the ON and OFF buttons simultaneously for 3 seconds to enter childproof mode as shown in this picture. 2. The transmitter will not send a signal again until childproof mode is deactivated by pressing the ON and OFF buttons simultaneously for 3 seconds to exit childproof mode and the Childproof indicator disappears from LCD. Transmitter Thermal Shutdown: 1.
PAGE 8
TESTING YOUR NEW REMOTE CONTROL SYSTEM 1. 2. 3. 4. 5. Light your gas appliance following the appliance lighting instructions that came with the appliance. Confirm that the pilot light is on; it must be in operation for the remote control to operate the main gas valve. Appliance control knob must be in the ON position, and appliance ON/OFF switch must be in OFF position. Slide the 3 position button on the remote receiver to the ON position and the main gas flame should ignite.
PAGE 9
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.