User Manual
Table Of Contents
- Appendix B: Command Generator Examples
- B.1 Device Discovery and Remote Name Request
- B.2 Establish Baseband Connection
- B.3 Baseband Disconnection
- B.4 Create Audio Connection
- B.5 L2CAP Connection
- B.6 L2CAP Channel Disconnect
- B.7 SDP Profile Service Search
- B.8 SDP Reset Database and Add Profile Service Record
- B.9 RFCOMM Client Channel Establishment
- B.10 RFCOMM Client Channel Disconnection
- B.11 RFCOMM Register Server Channel
- B.12 Establish TCS Connection
- B.13 OBEX Server Init
- B.14 OBEX Client Connection and Client Get & Put
- Appendix C: Merlin’s Wand Scripting Commands
- C.1 Bluetooth Addresses
- C.2 Basic Commands
- C.3 Pipe Commands
- C.4 HCI Commands
- HCIAcceptConnectionRequest()
- HCIAddSCOConnection()
- HCIAuthenticationRequested()
- HCICatcBerTest()
- HCICatcChangeHeadsetGain()
- HCICatcEnterTestMode()
- HCICatcReadHeadsetGain()
- HCICatcReadRevisionInformation()
- HCICatcSelfTest()
- HCICatcTestControl()
- HCICatcWriteCountryCode()
- HCIChangeConnectionLinkKey()
- HCIChangeConnectionPacketType()
- HCIChangeLocalName()
- HCIDeleteStoredLinkKey()
- HCIEnableDeviceUnderTestMode()
- HCIExitParkMode()
- HCIExitSniffMode()
- HCIHoldMode()
- HCIMasterLinkKey()
- HCIParkMode()
- HCIPINCodeRequestNegativeReply()
- HCIPINCodeRequestReply()
- HCIQoSSetup()
- HCIReadAuthenticationEnable()
- HCIReadBDADDR()
- HCIReadBufferSize()
- HCIReadClockOffset()
- HCIReadConnectionAcceptTimeout()
- HCIReadCountryCode()
- HCIReadCurrentIACLAP()
- HCIReadEncryptionMode()
- HCIReadLinkPolicySettings()
- HCIReadLinkSupervisionTimeout()
- HCIReadLocalName()
- HCIReadLocalSupportedFeatures()
- HCIReadLocalVersionInformation()
- HCIReadLoopbackMode()
- HCIReadNumberOfSupportedIAC()
- HCIReadPageScanMode()
- HCIReadPageScanPeriodMode()
- HCIReadPageTimeout()
- HCIReadPINType()
- HCIReadRemoteSupportedFeatures()
- HCIReadRemoteVersionInformation()
- HCIReadScanEnable()
- HCIReadSCOFlowControlEnable()
- HCIReadStoredLinkKey()
- HCIReadVoiceSetting()
- HCIRejectConnectionRequest()
- HCIRemoveSCOConnection()
- HCIReset()
- HCIRoleDiscovery()
- HCISetConnectionEncryption()
- HCISetEventFilter()
- HCISniffMode()
- HCISwitchRole()
- HCIWriteAuthenticationEnable()
- HCIWriteConnectionAcceptTimeout()
- HCIWriteCurrentIACLAP()
- HCIWriteEncryptionMode()
- HCIWriteLinkPolicySettings()
- HCIWriteLinkSupervisionTimeout()
- HCIWriteLoopbackMode()
- HCIWritePageTimeout()
- HCIWritePINType()
- HCIWriteScanEnable()
- HCIWriteStoredLinkKey()
- HCIWriteVoiceSettings()
- C.5 OBEX Commands
- C.6 RFCOMM Commands
- RFCloseClientChannel()
- RFOpenClientChannel()
- RFRegisterServerChannel()
- RFSendData()
- RFSendDataFromPipe()
- RFReceiveData()
- RFWaitForConnection()
- RFAcceptChannel()
- RFAcceptPortSettings()
- RFCreditFlowEnabled()
- RFRequestPortSettings()
- RFRequestPortStatus()
- RFSetLineStatus()
- RFSetModemStatus()
- RFSendTest()
- RFAdvanceCredit()
- C.7 TCS Commands
- C.8 L2CAP Commands
- C.9 SDP Commands
- C.10 Merlin Commands
- Appendix D: CATC Scripting Language
149
CATC MERLIN’S WAND 1.22 APPENDIX B
User’s Manual Command Generator Examples
B.11 RFCOMM Register Server Channel
Procedure
In this scenario, Merlin’s Wand registers a Server Channel.
This procedure assumes that an ACL connection has been established. See
“Establish Baseband Connection” on page 139.
Note A connection is not necessary to call a RegisterServerChannel command.
Step 1 From the RFCOMM menu select RegisterServerChannel.
Step 2 Click Execute.
The Event Log should indicate successful completion of the command
with the response “RegisterServerChannel_Complete.” On completion
of these steps, the application is ready to accept incoming RFCOMM
connections.