User Manual
Table Of Contents
- Appendix B: Command Generator Examples
- B.1 Device Discovery and Remote Name Request
- B.2 Establish Baseband Connection
- B.3 Baseband Disconnection
- B.4 Create Audio Connection
- B.5 L2CAP Connection
- B.6 L2CAP Channel Disconnect
- B.7 SDP Profile Service Search
- B.8 SDP Reset Database and Add Profile Service Record
- B.9 RFCOMM Client Channel Establishment
- B.10 RFCOMM Client Channel Disconnection
- B.11 RFCOMM Register Server Channel
- B.12 Establish TCS Connection
- B.13 OBEX Server Init
- B.14 OBEX Client Connection and Client Get & Put
- Appendix C: Merlin’s Wand Scripting Commands
- C.1 Bluetooth Addresses
- C.2 Basic Commands
- C.3 Pipe Commands
- C.4 HCI Commands
- HCIAcceptConnectionRequest()
- HCIAddSCOConnection()
- HCIAuthenticationRequested()
- HCICatcBerTest()
- HCICatcChangeHeadsetGain()
- HCICatcEnterTestMode()
- HCICatcReadHeadsetGain()
- HCICatcReadRevisionInformation()
- HCICatcSelfTest()
- HCICatcTestControl()
- HCICatcWriteCountryCode()
- HCIChangeConnectionLinkKey()
- HCIChangeConnectionPacketType()
- HCIChangeLocalName()
- HCIDeleteStoredLinkKey()
- HCIEnableDeviceUnderTestMode()
- HCIExitParkMode()
- HCIExitSniffMode()
- HCIHoldMode()
- HCIMasterLinkKey()
- HCIParkMode()
- HCIPINCodeRequestNegativeReply()
- HCIPINCodeRequestReply()
- HCIQoSSetup()
- HCIReadAuthenticationEnable()
- HCIReadBDADDR()
- HCIReadBufferSize()
- HCIReadClockOffset()
- HCIReadConnectionAcceptTimeout()
- HCIReadCountryCode()
- HCIReadCurrentIACLAP()
- HCIReadEncryptionMode()
- HCIReadLinkPolicySettings()
- HCIReadLinkSupervisionTimeout()
- HCIReadLocalName()
- HCIReadLocalSupportedFeatures()
- HCIReadLocalVersionInformation()
- HCIReadLoopbackMode()
- HCIReadNumberOfSupportedIAC()
- HCIReadPageScanMode()
- HCIReadPageScanPeriodMode()
- HCIReadPageTimeout()
- HCIReadPINType()
- HCIReadRemoteSupportedFeatures()
- HCIReadRemoteVersionInformation()
- HCIReadScanEnable()
- HCIReadSCOFlowControlEnable()
- HCIReadStoredLinkKey()
- HCIReadVoiceSetting()
- HCIRejectConnectionRequest()
- HCIRemoveSCOConnection()
- HCIReset()
- HCIRoleDiscovery()
- HCISetConnectionEncryption()
- HCISetEventFilter()
- HCISniffMode()
- HCISwitchRole()
- HCIWriteAuthenticationEnable()
- HCIWriteConnectionAcceptTimeout()
- HCIWriteCurrentIACLAP()
- HCIWriteEncryptionMode()
- HCIWriteLinkPolicySettings()
- HCIWriteLinkSupervisionTimeout()
- HCIWriteLoopbackMode()
- HCIWritePageTimeout()
- HCIWritePINType()
- HCIWriteScanEnable()
- HCIWriteStoredLinkKey()
- HCIWriteVoiceSettings()
- C.5 OBEX Commands
- C.6 RFCOMM Commands
- RFCloseClientChannel()
- RFOpenClientChannel()
- RFRegisterServerChannel()
- RFSendData()
- RFSendDataFromPipe()
- RFReceiveData()
- RFWaitForConnection()
- RFAcceptChannel()
- RFAcceptPortSettings()
- RFCreditFlowEnabled()
- RFRequestPortSettings()
- RFRequestPortStatus()
- RFSetLineStatus()
- RFSetModemStatus()
- RFSendTest()
- RFAdvanceCredit()
- C.7 TCS Commands
- C.8 L2CAP Commands
- C.9 SDP Commands
- C.10 Merlin Commands
- Appendix D: CATC Scripting Language
146
CATC MERLIN’S WAND 1.22 APPENDIX B
User’s Manual Command Generator Examples
B.8 SDP Reset Database and Add Profile Service
Record
Procedure
In this scenario, Merlin’s Wand resets the SDP database and then adds an
SDP Profile Service Record.
This procedure assumes that an ACL connection has been established
between Merlin’s Wand and the target device. “Establish Baseband
Connection” on page 139.
Note A connection is not necessary to perform a Reset_Database or
AddProfileServiceRecord.
Step 1 From the SDP tab select ResetDatabase.
Step 2 Click Execute.
The Event Log should indicate that the database was reset.
Step 3 Select AddProfileServiceRecord from the menu.
Step 4 Select a profile from the Profile menu.
Step 5 Select a server channel from the Channel menu.
Step 6 Click Execute.
Success will be indicated in the Event Log with
“AddProfileServiceRecord_Complete” and the type of profile added.