User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
field alert 71
group and channel 54, 55
listen to live data 69
load into analyzer 41
load using MRL 42
move to another memory location 29
multiple inputs 68, 69
overview 53
plot data 75
print report 78, 79
redo measurement 70
restore default values 65
sensors 65, 77
skip equipment or a point 71
view equipment and points 59
view saved 57
Route Data Collection screen 54, 55
Route Management 56
RPM
enter new value 65
runout
collect data 211
enable or disable 202
overview 210
view or remove from measurement 212
S
safe use 2, 3
screen captures 50
sensor
connectors 7, 31, 32
does not match route setup 65
inputs 95, 149, 168
set up 96, 150, 169, 199
sensor locations for Balance 198
serial number 14–16
shoulder strap 8
single-plane balance job 187, 192
ski-slope effect 109
slow roll 202, 211
slow speed equipment 109
specifications
hardware 257
input 259
measurement 258
spectrum
averaging 101
cascade 126
collect in Analyze 122
cursors 18, 19
data units in Analyze 97
data units in ODS/Modal 169
display Analyze data 94
display in ODS/Modal 172
display in route report 78, 79
display route data 60, 62
lines of resolution 100
overlap 62, 94
plot in Route 75
route 68, 69
smeared 115
switch plot type 82
units in Advanced Transient 154
view peaks 84
windows 100
splash screen
add/change 50
delete 51
displayed 14–16
Split Angle 232
stand 7
Standalone Data Transfer 35, 36
standard equipment 5
standby 14, 21
Static/Couple Analysis 234
status beeper 20
Status LED 6
status messages 72
storage temperature 257
Sum Weights 233
summary report
create 78, 79, 228
print 78, 79, 228
Synchronous Analysis 116
Synchronous Averaging 116
Synchronous Time averaging 101
T
tachometer setup
delete 68, 99, 153, 172, 196
open 67, 98, 152, 171, 196
rename 68, 99, 152, 171, 196
save 67, 98, 152, 171, 196
tachometers
set location 197
set rotation 197
technical support 3, 4
temperature limits 257
temperature measurement 131
time and date 14–16, 23
timer
backlight 21
Index
273
DRAFT