t @o@c t @o@c i T w@c T q@r U v @m r @m @M@b @r p@ @c@Hlcd@r @oI Rw@r @b@f Qw@r @b@f By Firstech, LLC 2 U V V W Y g @s @f s @c r @c a @l@O@a@@u@O@d p @l@O@a a@t@r @s@f m@t@r @s@f@Hr @m I a
Introduction Thank you for purchasing a Firstech system for your vehicle. In order to truly enjoy the benefits of this system, we recommend that you thoroughly review the following manual. Please note that this manual applies to the 2 Way - 4 Button Liquid Crystal Display Remotes, regardless of whether you purchased the alarm only, starter only or alarm/starter combination. This manual also supports your 1 Way Fiancé remotes that may be included with your system.
Quick Reference r @m Mb @r The only regular maintenance this system requires is remote control battery replacement. No programming is required when replacing the battery. Two Way Remotes: First, release the battery cover lock located on the back of the remote. Once the lock is released, gently slide the battery cover off to expose the battery. With the exception of the 2WSSR-PRO (Uses 1 AA battery) all Firstech 2 Way remotes require one AAA battery.
Quick Reference Quick Reference R@w@r @b@f Button Duration AdditionalProgramming Required Function / Description 0.5 seconds yes 2.5 seconds Duration AdditionalProgramming Function / Description Required Drive lock. Activates ignition controlled door locks 0.5 seconds no Locks doors and / or arms alarm. no Option programming menu 2. For use during installation 3.5 seconds no Panic/vehicle locater (flashes vehicle’s parking lights and sounds siren and horn) 0.
Quick Reference Remote LCD(liquid crystal display) Diagram and icons Your remote pager will indicate the status of your vehicle while in range. The unique LCD design will visually display such icons as lock/unlock status, remote start confirmation and remaining run-time, impact/shock notification, battery voltage, temperature display and much more. Q@w@r @b@f Button Duration Additional Programming Function / Description Required 0.5 seconds yes Drive lock.
Remote LCD(liquid crystal display) Diagram and icons c@iM Remote LCD(liquid crystal display) Diagram and icons s @iM Engine Running This icon will be displayed while the vehicle is running after it has been remote started. Lock/Arm - Unlock/Disarm This icon indicates whether the system is locked/armed or unlocked/disarmed. While armed, the system will monitor the doors, trunk, hood, shock sensor, and aux inputs.
Impact This icon will be displayed if an impact to the vehicle is detected while the system is armed. The remote will beep rapidly while displaying this icon if the impact is hard; this means that the alarm was triggered. If it beeps slowly while displaying this icon, that means that the impact was soft and that the alarm simply gave four warning chirps. Door This icon will be displayed if the door is opened while the system is armed. The remote will beep rapidly while displaying this icon.
General System Functions The remote transmitter functions have been predetermined and programmed from the factory. The four button configuration allows for many functions to be performed through a series of tapping, holding and / or multiple presses of buttons. Sending Commands When in range, and a command has been sent, the remote pager backlight will illuminate, the remote will beep and the appropriate icon will be displayed.
General System Functions m@t@r @s@f@Hr @m I In order to remote start a manual transmission vehicle, the system must first be set in Reservation Mode. Reservation Mode must be set each and every time you want to remote start a manual transmission vehicle. The purpose of Reservation Mode is to leave the transmission in neutral before exiting the vehicle. IMPORANT The transmission must be left in the neutral position. The vehicles windows must be rolled up.
General System Functions a@o@O@w@rMd@O@s@d Your system is equipped with two additional outputs that can be configured to control windows, open power sliding doors, open a power sliding moon roof, or even turn on a rear defroster. These outputs can be configured for pulsed, timed or latched settings. Your authorized Firstech dealer can set these outputs up accordingly.
General System Functions s@s @oOo Hold buttons (I+III) simultaneously for 2.5 seconds to turn on and off the shock sensor. The remote will beep twice and the shock sensor icon will illuminate to confirm the shock sensor is off. The remote will beep once and the shock sensor icon will disappear to confirm the shock sensor is on. IMPORTANT: Turning off the shock sensor also turns off the optional sensor.
Advanced System Functions R c@m @Hm @v @cI Most 2 Way remotes have the ability to operate a 2nd vehicle. Hold buttons (III+IV) for 2.5 seconds to activate this feature. The remote will beep once and the 2nd car icon will illuminate to confirm that 2nd car mode is activated. The remote will beep twice and the icon will disappear to confirm 2nd car mode is off. IMPORTANT: 2nd car mode requires the remote to be programmed to a 2nd vehicle that is equipped with the same system.
Advanced System Functions s @v @s Advanced System Functions t @s@m IMPORTANT: The first two digits of the RPS unlock/disarm pass code will be the default pass code for the secure valet - you do not need to program them independently. If you are not using the RPS unlock, following the below procedures to program your secure valet pass code; Timer start mode is used to cool or warm the vehicle automatically without use of the key or the remote.
Advanced System Functions Advanced System Functions c@O@h@s@m a@j@m Cold/hot start mode works in conjunction with timer start mode (see above) and the temperature sensor. It allows you to configure your timer start feature to check the vehicle’s temperature prior to starting. All of these options require programming from your local dealer. Your system has a mode that requires you to keep your remote separate from your key chain. This feature also requires additional labor.
Remote Coding / Programming Routine (S) IMPORTANT: Every Firstech remote must be coded to the system prior to performing any operations. All remotes must be coded at the same time. Programming 2 Way 4 Button Remotes: p@Z@R@w@T@b@r Z STEP 1: Activate Valet/Programming mode by manually turning the ignition key on and off (between the Acc & On positions) five times within 7 seconds. The vehicle’s parking lights will flash once with the successful completion of this step.
Alarm Diagnostic Limited Lifetime Warranty While the alarm is armed, the LED will blink slowly. While the siren is going off, the LED will indicate the specific zone that was triggered.
By Firstech LLC Version 1.0 21911 68th Ave S Kent, WA 98032 8102REUSC000702 / CS-2WLCD-ES Toll Free : 888-820-3690 Toll Free : 888-820-3690 8102REUSC000702 / CS-2WLCD-ES By Firstech LLC Version 1.
